LaCie 12big Rack Fibre 8 Bedienungsanleitung

12big rack ﬁbre 8

Quick Install Guide

LaCie 12big Rack Fibre 8 Table of Contents

Quick Install Guide page 1

Table of Contents

1. Introduction............................................................................................................. 2

1.1. Safe Handling ......................................................................................................................... 2

1.2. Safety...................................................................................................................................... 2

1.3. Rack System Precautions .......................................................................................................... 2

1.4. PCM Operation ....................................................................................................................... 3

1.5. ESD Precautions....................................................................................................................... 3

1.6. Battery Disposal....................................................................................................................... 3

2. Preparation ............................................................................................................. 4

2.1. Before you begin ..................................................................................................................... 4

2.2. Unpackaging the Storage System.............................................................................................. 4

2.3 Removing the PCMs and Disk Drives ......................................................................................... 4

3. Rack Installation ...................................................................................................... 5

3.1. Rack Installation Prerequisites ................................................................................................... 5

3.2. Rack Installation Procedures ..................................................................................................... 5

4. Setup and Cabling................................................................................................... 6

4.1. Installing the SFP Modules........................................................................................................ 6

4.2. Cabling the Enclosures............................................................................................................. 7

4.3. Cabling Multiple Enclosures ..................................................................................................... 8

4.4 Connecting the Power Cords and Powering On the System......................................................... 8

EN English

LaCie 12big Rack Fibre 8 Introduction

Quick Install Guide page 2

Introduction1.

Safe Handling1.1.

Safety1.2.

caution: If this equipment is used in a manner not

speciﬁed by LaCie, the protection provided by the equipment

may be impaired.

caution: The RJ45 socket on the RAID Controller is for

Ethernet connection only and must not be connected to a

telecommunications network.

iMPoRtant note: Class 1 Laser Product. The LaCie

12big Rack Fibre 8 RAID Controller is supplied with optical

SFP Transceiver modules. They contain a laser that

complies with Laser Class 1, US 21 CFR (J) & EN 60825-1,

UL (NRTL) and TUV.

iMPoRtant: The optical modules provided and installed by

the end user must be a UL (or other North America NRTL)

RECOGNIZED COMPONENT and must be approved by TUV

(or other European product safety test house), and the laser in

the module must comply with Laser Class 1, US 21 CFR (J)

and EN 60825-1).

Rack System Precautions1.3.

PCM Operation1.4.

WaRninG: Do not remove the covers from the PCM. Danger of

electric shock inside. Return the PCM to LaCie for replacement.

WaRninG: Do not remove a PCM unless a replacement can

be installed immediately. The enclosure must not be operated

without all modules in place.

ESD Precautions1.5.

Battery Disposal1.6.

WaRninG: There is a danger of explosion if the battery is

disposed of improperly. Dispose of used batteries in accordance

with LaCie’s instructions and national regulations.

caution: There is a danger of explosion if the RAID

Controller battery is disposed of improperly. Dispose of

used batteries in accordance with LaCie’s instructions and

national regulations.

LaCie 12big Rack Fibre 8 Introduction

Quick Install Guide page 3

LaCie 12big Rack Fibre 8 Preparation

Quick Install Guide page 4

Preparation2.

Before You Begin2.1.

Before you begin, make sure the site where you intend to set

up and use your storage system has the following:

• Standard AC supply power from an independent source or

a rack power distribution unit with a UPS.

• Host computer with a standard Fibre Channel HBA (host

bus adapter) with the latest BIOS and drivers. Follow the

instructions provided with your host bus adapter, and install

the HBA and its driver software, if necessary.

For Microsoft Windows Servers - Insert the Software and

Manuals Disc, click the Pseudo LUN Driver (INF) button and

following the on-screen installation instructions.

Unpacking the Storage System2.2.

The Accessory Box contains the AC power cord(s), the Software

and Manuals Disc, anti-tamper lock key, host interface cables,

expansion cables, RS232 cables, and the rails-hardware parts

for rack mounting.

Position the shipping packaging within close proximity 1.

of the site where you intend to install the storage system.

Inspect the packaging for crushes, cuts, water damage,2.

or any other evidence of mishandling during transit.

If any damage appears to be present, it is suggested to

take photographs before opening any boxes. You may

Figure 1: Unpacking the Storage System

wish to contact the shipping company if there is

apparent damage.

Open the carton top, and remove the accessory kit box.3.

Lift the top foam component of the packaging from4.

the enclosure.

Remove the protective plastic wrapping and inspect for5.

obvious damage.

Lift the enclosure from the carton and place it on a6.

stable work surface. It is advisable to minimize the

weight by removing the Power Cooling Modules

(PCM) and the top row of Disk Drives, before lifting

the enclosure from the carton.

iMPoRtant note: Refer to section 2.3 “Removing the

PCMs and Disk Drives” for the proper removal procedures.

Once you have the enclosure on a stable work surface,7.

remove the remaining Disk Drives, RAID Controllers or

Disk I/O Modules in preparation for rack installation.

Removing the PCMs2.3.

and Disk Drives

Remove the PCMs.1.

Grasp the latch and the side of the PCM handle

between your thumb and foreﬁnger, then squeeze

together and open the handle to eject the PCM.

Then grip the handle and withdraw the PCM from the

enclosure bay. Repeat for the remaining PCMs.

Remove the Disk Drives.2.

Insert the lock key provided into the cutout in the Drive

Carrier handle and into its socket. Rotate the key

counter-clockwise until the “red” indicator is not visible.

Release the Drive Carrier module handle by pressing

the latch in the handle with your ﬁnger and rotating

the handle outward and towards the right. Withdraw

the Drive Carrier from the drive slot. Repeat for the

remaining drives.

LaCie 12big Rack Fibre 8 Preparation/Rack Installation

Quick Install Guide page 5

• The fully populated enclosure weighs about 27 kg (59 lb).

It is not recommended to lift the enclosure by yourself.

• Minimum depth of 700 mm (27.6 inches) from rack post to

post (vertical members). This dimension includes cabling.

• A minimum gap of 25 mm (1 inch) clearance between the

rack door and front of the enclosure; and 50 mm (2 inches)

rear clearance between the rear of the enclosure and the

rear of the rack is recommended in order to maintain the

correct air ﬂow.

• The rack should present a maximum back pressure of 5

pascals (0.5 mm water gauge). A pascal count of 5 or greater

can restrict airﬂow and could cause cooling problems.

Rack Installation Procedures3.2.

With the enclosure on a stable work surface, attach the1.

left and right chassis slides to the enclosure sides using

a total of 10 M3 x 4 button head screws, ve on each

side. The front portion of the chassis slide has two tangs

which insert into holes on the forward edge of the side

panel. (See Figure 3.)

Assemble the left and right chassis latches using the 2.

chassis latch screws. Ensure that the latch is orientated

as shown in Figure 3, with the spring arm located

against its stop. On the right hand side this is at the top,

on the left hand side it is at the bottom.

Figure 3: Securing Chassis Slides to Enclosure

Figure 2: Removing PCMs and Disk Drives

Rack Installation3.

Rack Installation Prerequisites3.1.

The LaCie 12big Rack Fibre 8 and LaCie 12big Rack Fibre

8 enclosures are designed for installation into an industry

standard 19-inch cabinet.

LaCie 12big Rack Fibre 8 Rack Installation/Setup and Cabling

Quick Install Guide page 6

Front attach points only. Remove this nut

for tapped hole rack installations.

Figure 5: Mounting the Enclosure into a Rack

Figure 4: Securing Brackets to Rack - Left Hand Assembly Shown

Figure 6: Installing the SFP Module

Assemble the rack brackets to the rack posts as follows. 3.

The bracketsare universal and will ﬁt either side.

(See Figure 4.)

a. Locate the guide pin at the rear of each bracket

and insert that pin into a rear rack post hole. Attach

the bracket to the rear rack post using the washers and

screws supplied. The screws should be left loose.

b. Extend the rail to t between the rack posts.

c. Attach the bracket to the front rack post using the

washers and screws supplied. The screws should be

left loose.

d. Tighten the two clamping screws located along the

inside of the rear section of the rack bracket.

Mount the enclosure in the rack as follows:4. (See Figure 5)

a. Using an assistant, lift the enclosure aligning it with

the rack rails and carefully insert the chassis slides into

the rack rails.

b. Push the enclosure completely into the rack cabinet.

c. Tighten the rear rack bracket mounting screws,

that were previously left loose.

d. Withdraw the enclosure until it reaches the hard stops

(approximately 400 mm (15.75 inches)).

e. Tighten the front rack bracket mounting screws, that

were previously left loose.

f. Push the enclosure completely into the rack cabinet

and attach to the front of the rack using the captive

Setup and Cabling4.

Installing the SFP Modules4.1.

Insert the SFP transceiver module into the SFP cage and1.

push to seat it. Ensure the ejector is positioned to its

stored location.

Install the remaining SFP transceiver modules into the2.

remaining open SFP cages as desired.

Install the ﬁber channel cables as indicated in the3.

cabling diagrams listed in section 4.2.

fasteners on the front anges (located just outside

of the handles).

Re-install the plug-in modules removed in preparation5.

for the installation, then continue with section 4.1, 4.2,

4.3 and 4.4 to complete the installation.

LaCie 12big Rack Fibre 8 Setup and Cabling

Quick Install Guide page 7

Cabling the Enclosures4.2.

Figures 7 through 14 depict the supported cabling

conﬁgurations. Locate the ﬁgure that depicts your

conﬁguration and Cabling Multiple Enclosures.

Figure 12: Dual Hosts, Single HBAs, and Dual Controller Cabling with a Switch

Figure 7: Single Host, Single HBA, and Single Controller Cabling

Figure 8: Dual Hosts, Single HBAs, and Single Controller Cabling

Figure 9: Single Host, Dual HBAs, and Dual Controller Cabling

Figure 10: Dual Hosts, Single HBAs, and Dual Controller Cabling

Figure 11: Dual Hosts, Dual HBAs, and Dual Controller Cabling

iMPoRtant note: Refer to section 2.3 “Removing the

PCMs and Disk Drives” for the proper removal procedures.

LaCie 12big Rack Fibre 8 Setup and Cabling

Quick Install Guide page 8

Figure 14: LaCie 12big Rack Fibre 8 expansion enclosure: Dual Host,

Dual Controller Cabling with a Switch

Figure 15: Connecting the AC Power Cords

Figure 8: Simplex: Single Host (Single HBA)

Cabling Multiple Enclosures4.3.

Figures 13 and 14 depict the multiple enclosure supported

cabling conﬁgurations. Locate the ﬁgure that depicts your

conﬁguration and cable it accordingly.

Connecting the Power Cords4.4.

and Powering On the System

Connect the power cords to the PCMs. Move the bale1.

out of the way, insert the cord and place the bale over

and onto the cord. Repeat for the other PCMs.

Ensure the ON/OFF switch is in the OFF position.

Attach the power cords to the Power Distribution Units, 2.

ensure they use separate power sources.

Power on the storage system by placing each of the3.

PCM ON/OFF switches to the ON position.

For more details refer to the LaCie 12big Rack Fibre 8 User

Guide, as well as the StorView Storage Management Software

RAID Module User Guide and the VT-100 RAID Conguration

Utility User Guide.

Figure 13: LaCie 12big Rack Fibre 8 expansion enclosure: Dual Hosts,

Dual Controller Cabling

Andere Handbücher für 12big Rack Fibre 8

Inhaltsverzeichnis

Andere LaCie Lagerung Handbücher

LaCie

LaCie CloudBox Bedienungsanleitung

LaCie

LaCie Fuel Bedienungsanleitung

LaCie

LaCie 301534 Bedienungsanleitung

LaCie

LaCie 301371 - Rugged Hard Disk 500 GB External... Bedienungsanleitung

LaCie

LaCie MINI COMPANION HARD DRIVE U S B 2. Bedienungsanleitung

LaCie

LaCie LITTLE BIG DISK THUNDERBOLT 2 Bedienungsanleitung

LaCie

LaCie 12big Rack Fibre 8 Bedienungsanleitung

LaCie

LaCie Extreme Bedienungsanleitung

LaCie

LaCie LaCinema PlayHD Bedienungsanleitung

LaCie

LaCie d2 Quadra USB 3.0 Bedienungsanleitung

LaCie

LaCie USB 2.0 Bedienungsanleitung

LaCie

LaCie Big Disk USB 2.0 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

LaCie

LaCie Porsche Design P 9230 Bedienungsanleitung

LaCie

LaCie Little Disk Bedienungsanleitung

LaCie

LaCie Chrome Bedienungsanleitung

LaCie

LaCie 300718 Bedienungsanleitung

LaCie

LaCie 301527 Bedienungsanleitung

LaCie

LaCie Hard Drive Porsche Bedienungsanleitung

LaCie

LaCie CurrenKey Bedienungsanleitung

LaCie

LaCie D2 BLU-RAY XL Bedienungsanleitung

LaCie

LaCie Silverscreen Bedienungsanleitung

LaCie

LaCie Rugged RAID Shuttle Bedienungsanleitung

LaCie

LaCie USB Key MAX Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung

Quantum

Quantum PX506 Bedienungsanleitung