Lafayette EZ-Charge V2 Installationshandbuch

EZ-Charge V2

Mul-Channel Remote

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions

[1] This device may not cause harmful interface, and

[2] This device must accept any interference received, including interference that may cause undesired op-

eraon.

Package Contents

1 x 15 channel remote

1 x magnec holder including wall xing screws

1 x 3V CR2450 baery

For Motorizaon Technical Support call 877-548-0612

EZ-Charge Programming Instructions

Installaon

Wall Mount Holder

Remove cover from base by prying with at

head screwdriver

Used supplied fasteners and anchors to

aach the base to the wall

Replace cover by pressing snap latches into

place.

Baery

Remove cover from remote press gently in

and down to disengage cover.

Install baery with posive (+) side facing

up.

For Motorizaon Technical Support call 877-548-0612

Programming

Pairing Motor to a Remote

Select channel on controller Hold P1 buon on the motor head

for 1 jog

Hold STOP on controller

Motor Response Motor Response

Check Motor Direcon

To check travel direcon of shade, press UP

or DOWN on controller.

To reverse shade direcon, hold both UP

and DOWN.

Motor Response

Seng Limits

Move shade to desired highest or lowest

posion by pressing the UP or DOWN

buons

Holding DOWN will make the shade travel.

Pressing DOWN buon moves the shade in

small movements. You must press the

STOP buon if the shade is traveling.

Holding UP will make the shade travel.

Pressing UP buon moves the shade in

small movements. You must press the

STOP buon if the shade is traveling.

Once you are at your upper limit, hold UP and

STOP.

Once you are at your lower limit, hold DOWN

and STOP.

DONE!

For Motorizaon Technical Support call 877-548-0612

Adjusng Upper Limit

You can do this at ANY posion. Shade does not need to be at the current upper limit.

Hold UP and STOP on the

controller.

Move shade to desired

posion

Hold UP and STOP on the

controller.

Adjusng Lower Limit

You can do this at ANY posion. Shade does not need to be at the current lower limit.

Hold DOWN and STOP on

the controller.

Move shade to desired

posion

Hold DOWN and STOP on

the controller.

Copy / Delete channels

Hold P1 buon on the motor

head for 1 jog.

Select channel you wish to

add or delete

Hold the STOP buon on the

controller

Delete All Sengs

Hold P1 on the motor head

for 4 connuous jogs

For Motorizaon Technical Support call 877-548-0612

Favorite Posion

You will need to put a motor to sleep if you are going to program mulple shades on the same channel or adjust a limit for a

specic shade on a group channel. To wake the shade up just press and release the P1 motor head buon.

Hold P1 on the motor head

for 2 connuous jogs

Pung motor to sleep

Move shade to the desired favorite posion

Remove baery door on remote.

Press and release P2 on the upper

le corner. The shade will jog once.

Press and release the STOP

buon on the controller

and the shade will jog

Press and release the STOP

buon on the controller

and the shade will jog

For Motorizaon Technical Support call 877-548-0612

Tilt Mode

Hold UP and DOWN on the

controller for 1 jog

Hold UP and DOWN on the

controller for 1 jog

In this mode if you just press and release a direcon the shade will only move in small increments. This is nice for the Transional

shades. If you want the shade to travel all the way up or all the way down , press and HOLD that direcon. To exit this mode and

revert back to Roller Mode, do the same steps.

Adjusng Motor Speed

Remove baery door on remote.

Press and release P2 on the upper

le corner. The shade will jog once.

Press UP shade will make 1

jog

Press UP shade will make 2

jogs

To Increase speed

Press DOWN shade will

make 1 jog

Press DOWN shade will

make 2 jogs

To decrease speed

For Motorizaon Technical Support call 877-548-0612

EZ-Charge V2

Surface Mounted Wireless Wall Switch

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions

[1] This device may not cause harmful interface, and

[2] This device must accept any interference received, including interference that may cause undesired op-

eraon.

Package Contents

1 x Switch

1 x Single gang Decora style wall plate (incl 2 mounng screws)

1 x 3V CR2430 baery

For Motorizaon Technical Support call 877-548-0612

Installaon

Wall Mount Holder

Open rear baery cover by gently separang

switch covers with screwdriver

Install CR2430 baery with posive side facing

up. Snap covers back together.

Baery

For Motorizaon Technical Support call 877-548-0612

Used supplied fasteners and anchors as

needed to aach base.

Programming

Pairing Motor to a Remote

Select channel on controller Hold P1 buon on the motor head

for 1 jog

Hold STOP on controller

Motor Response Motor Response

Check Motor Direcon

To check travel direcon of shade, press UP

or DOWN on controller.

To reverse shade direcon, hold both UP

and DOWN.

Motor Response

Seng Limits

Move shade to desired highest or lowest

posion by pressing the UP or DOWN

buons

Holding DOWN will make the shade travel.

Pressing DOWN buon moves the shade in

small movements. You must press the

STOP buon if the shade is traveling.

Holding UP will make the shade travel.

Pressing UP buon moves the shade in

small movements. You must press the

STOP buon if the shade is traveling.

Once you are at your upper limit, hold UP and

STOP.

Once you are at your lower limit, hold DOWN

and STOP.

DONE!

For Motorizaon Technical Support call 877-548-0612

Adjusng Upper Limit

You can do this at ANY posion. Shade does not need to be at the current upper limit.

Hold UP and STOP on the

controller.

Move shade to desired

posion

Hold UP and STOP on the

controller.

Adjusng Lower Limit

You can do this at ANY posion. Shade does not need to be at the current lower limit.

Hold DOWN and STOP on

the controller.

Move shade to desired

posion

Hold DOWN and STOP on

the controller.

Copy / Delete channels

Hold P1 buon on the motor

head for 1 jog.

Select channel you wish to

add or delete

Hold the STOP buon on the

controller

Delete All Sengs

Hold P1 on the motor head

for 4 connuous jogs

For Motorizaon Technical Support call 877-548-0612

Inhaltsverzeichnis

Andere Lafayette Fernbedienung Handbücher

Lafayette

Lafayette Auto-Lift Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung