Lampo IP66 Bedienungsanleitung

USER’ S MANUAL release 2.0

This manual must be considered an integral part of the projector.

BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE

INSTRUCTIONS IN THIS MANUAL.

QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE

INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.

BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE

VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.

FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:

[email protected]

LED RADIATION, DO NOT STARE INTO BEAM, CLASS 2 LED PER IEC 60825-1.

For additional information on these led devices with regard to the IEC 60825-1 standard, contact SEOUL Semiconductors.

SOLID: Dust-tight

WATER: Protected against heavy seas

Suitable for direct mounting on normally flammable surfaces

Minimum distance from lighted objects (0.3 meters)

Rated maximum ambient temperature (indoor without high-temperature control)

Connection must be made to a power supply system fitted with efficient

earthing (EN60598-1 – Class I fixture)

Replace any cracked protective shield, dichroic filter or lens

Index

Dimensions and weight -------------------------------------------------------------------------------- page 2

Technical data ------------------------------------------------------------------------------------------- page 2

Storage ---------------------------------------------------------------------------------------------------- page 2

Admissible environmental conditions --------------------------------------------------------------- page 2

Installation ----------------------------------------------------------------------------------------------- page 3

Example of installation --------------------------------------------------------------------------------- page 3

Signal cable selection ----------------------------------------------------------------------------------- page 4

EIA485 specifications ----------------------------------------------------------------------------------- page 4

Power supply connection ------------------------------------------------------------------------------ page 5

DMX signal connection -------------------------------------------------------------------------------- page 5

Schematic menu ----------------------------------------------------------------------------------------- page 6

User’s interface ------------------------------------------------------------------------------------------ page 7

Functions menu ------------------------------------------------------------------------------------------ page 7

DMX control mode -------------------------------------------------------------------------------------- page 9

Spare parts ------------------------------------------------------------------------------------------------ page 16

Dimensions & weight

Weight: 5,2 Kg

Technical data

- Aluminium body with cooling fins

- IP66 protection rate

- Thermal-shock resistant glass, IK08

- The projector can be installed in any position

- Input voltage range: from 85 to 265 Vac

- Frequency: 50-60 Hz

- 0,95 PFC electronically controlled

- Current controlled led

- Max power consumption: 44W (When all led are on at max power)

- 12 LEDs full colour 3.6W P5 by SEOUL Semiconductors (each LED’s case contain 77Lumen of RGB dices)

- High quality 35mm PMMA lenses by FRAEN

- Works via signal DMX

- Works in stand alone mode (Master/Slave)

- Can works in stand alone mode via infra-red remote control

- LED remote control code AS148

Storage

The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.

Attention, the projector will be damaged during the unpacking.

Admissible environmental conditions

The projector was engineered and produced to function in outdoor areas with an air temperature ranging between -20°C and

+50°C (thanks to inside high-temperature control) and with a humidity level between 30 and 90%.

When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area.

Installation

The projector can be installed in any position, use diameter 10mm holes of the steel bracket to fix the projector.

Unscrew the side screws to adjust the projector body angle.

We suggest to install a supplementary safety steel chain or cable

The area exposed to the wind is 0.08 square meters.

Unscrew two upper screws to open the lid and have access to the display.

Example of installation

If only one projector is on stand alone mode the signal cable is not necessary.

If the projectors are driven by a DMX controller or projector Master drive other projectors Slave, they need to be connected

together, with DMX signal cable, following the instructions of this manual.

The DMX signal is generated by a DMX controller, the signal cable goes in and out from each projector up to the last one.

The projectors will execute the same scenes if the DMX addresses are the same (factory set is 1) or they can be driven one by

one if the DMX addresses are different from each other.

Default mode 7C d: each projector uses 8 DMX channels

Projector 1: DMX address 1 Projector 2: DMX address 9 Projector 3: DMX address 17………….

If the DMX controller is not switched on, the projectors can be in black-out mode, generate light at 15% (default setting) or

generate light at 100%. Change this parameter at – DM.DE of menu.

It is possible to use MASTER/SLAVE function: One projector (Master) functioning in stand alone mode with resident

programs and a group of projector (Slave) execute, thanks to dmx signal and signal cables, the same sequences of colours.

The projectors can be fed from different power sources, it is not necessary to switch on the projectors at the same time.

Signal cable selection

Use only shielded and twisted cables with EIA485 (RS485) standards. The cable must be low capacity and with an impedance

between 82 and 120 ohm. It is preferable not to use audio cables.

The wire size we recommend is 26 AWG or higher.

If the projector have cable clamps, the external diameter of cable must be compatible with cable clamps.

We suggest to use our selection signal cable.

CAV99/040: Flexible signal cable for in-door.

One pair of cable plus shield and inside safety wire.

Impedance 120 Ohm.

CAV99/037: Polyurethane flexible signal cable for out-door.

One pair of cable plus shield drain wire and inside safety Kevlar wire.

Impedance 120 Ohm.

EIA485 specifications

It is preferable:

- Not to insert more than 32 projectors for each DMX chain.

- Not to use more than 150m of signal cable (low quality cable) or 300m of signal cable (good quality cable).

- Not to duplicate “T” way the signal cable, use a DMX Splitter.

Standard DMX controllers have only one signal out-put. If more than 32 projectors are used it is necessary to have a signal

SPLITTER, that will duplicate the signal in 2 or more lines.

If the signal cable is very long, it is necessary to install a signal AMPLIFIER on the DMX line (at least every 300m of good

quality cable), so that it will repeat the signal to the following projectors.

It is preferable, on the last projector of the dmx signal chain, to insert a resistor (from 82 to 120 ohm) between positive and

negative terminal (+ and -).

Always, use Male XLR 3 or 5 pin connector to connect the projectors to the DMX controller.

Solder on PIN 1 of the XLR connector the shield of the signal cable, on PIN 2 solder the negative (example: black wire of

cable) and on PIN 3 solder the positive (example: red or white wire of the cable). The sequences and the colours has to be the

same on the terminal connection blocks, do not change the sequences.

Power supply connection

It is advised to check the electric system before installation. From 85Vac to 265Vac (50 o 60 Hz).

Disconnect mains power supply before any operations.

Connect the fixture to the mains. See the table and the drawing for the colours of the connection cable.

Do not power the projector with a dimmer circuit

Protect the electric system with highly sensitive differential circuit breaker, 30mA.

When in doubt, consult a qualified electrician.

The cable’s diameter must be compatible with the cable clamp of the projector (PG 13.5), diameter from 6 to 12mm.

Projector is complete grounded, it is necessary to connect the middle terminal connection block at grounding system.

DMX signal cable connection

The IN and OUT signal cables must be connected directly to the terminal block inside the projector. Use the PG9 cable clamps

on the projector).

The external diameter of cable must be included between 4 and 7mm (PG9 cable clamps).

Schematic menu

Following the list of menu and submenu.

User’s interface

Use display interface to modify: functions, DMX starting address and to set

stand alone mode.

Use the buttons + and -to surf the menu’s function.

To enter into the menu, you have to push the Mode button and after that you

can search for the desiderate function and push the Enter button to enter in

it.

Push the Enter button to change DMX starting address and press the Enter

button to confirm.

In the address view mode, for example A.001, if the point after the letter A is blinking the board is receiving DMX signal, if

the point is static there’s no DMX signal.

Functions menu

- A.001: (dmx address) DMX starting address (first channel).

Default value 001

Go into pushing Enter , choose the value with + and - and push Enter to confirm.

- DM.PA: (dmx patch) Patch of the board, from 1 to 14 dmx channel.

Default value 7C d

Go to this submenu pushing Mode , choose DM.PA with + and - and push Enter to enter in. Use + and - to select the

desiderate patch and push Enter to confirm

On the table below you can see the summary of the channels, go to page 10 to see the detailed functions.

Ch. dmx 7C d 1C 3C 3C d 4C 4C d 13C d

1 Green Dimmer Green Green Green Green Green

2 Red Red Red Red Red Green fine

3 Blue Blue Blue Blue Blue Red

4 Amber Dimmer Amber Red fine

5 Strobe sync Dimmer Blue

6 Strobe Blue fine

7 Strobe delay Amber

8 Dimmer Amber fine

9 Strobe

10 Dimmer

11 CTCwhite

12 Fadespeed

13 Frequency

14 Frequency fine

- DM.DE: (dmx delay). When DMX signal is missing, the board keeps the last DMX value received for a set period

according to this functions. After the programmed seconds, the board will execute the function according to DM.ST function,

so you can have: black-out, leds on at 15% or led on at 100%.

Default value 003 seconds

Go to this submenu pushing Mode , choose DM.DE with + and - and push Enter . Use + and - to select the desiderate

value and push Enter to confirm. Time is setted in seconds, the value start from UNL (unlimited) to 999.

- DM.ST: (leds state when DMX signal isn’t received). When the board is switched on and DMX signal is missing, the

board can do this functions: black-out, leds on at 15% or led on at 100%.

Default value 15.ON

Go to this submenu pushing Mode , choose DM.ST with + and - and push Enter . Use + and - to select the desiderate

value and push Enter to confirm

Admissible mode:

15.ON, (15% ON) r,g,b,a channels ON at 15%

A.ON, (ALL ON) r,g,b,a channels ON at 100%

A.OFF, (ALL OFF) r,g,b,a channels OFF

- MA.IR: (master infrared) Whit I.R. sensor cabled, the board can run one of the stored Chase or do a fixed colour, that can

be controlled by the LED REMOTE.

LED REMOTE has 10m (free air) capacity.

Default value ON

Go to this submenu pushing Mode , choose MA.IR with + and - and push Enter . Use + and - to select the ON or OFF

and push Enter to confirm.

With red button of the LED REMOTE, you can switch ON or OFF the leds (ATTENTION: when you switched OFF the led,

the board is still running!!! ), with P+ e P- you can choose the program or change the colour. This function allows to use the

MASTER/SLAVE function.

ATTENTION: Disable MA.IR function on Slave boards. Two boards in Master mode can do several errors on DMX

transmission.

- ST.AL:(stand alone) The board can run in StandAlone mode with Master/Slave function.

Default value MS00

Go to this submenu pushing Mode , choose ST.AL with + and - and push Enter . Use + and - to select the macro

needed and push Enter to run it.

The board run in loop mode the Macro selected from M01 to M26 and output the DMX signal (master mode) for the other

board (slave).

To use Master/Slave function, all the boards need to be patched with the dmx patch 7C d !

StandAlone mode remains also if power supply is interrupted.

Macro Mode Colour changing

time (seconds)

Colour holding

time (seconds)

MA01 SLOW rainbow without amber 20 5

MA02 MEDIUM rainbow without amber 10 5

MA03 FAST rainbow without amber 5 5

MA04 SLOW rainbow without amber 20 2

MA05 MEDIUM rainbow without amber 10 2

MA06 FAST rainbow without amber 5 2

MA07 Very SLOW rainbow without amber 40 NO

MA08 SLOW rainbow without amber 20 NO

MA09 MEDIUM rainbow without amber 10 NO

MA10 FAST rainbow without amber 5 NO

MA11 SLOW Random colours without amber 10 NO

MA12 MEDIUM Random colours without amber 5 NO

MA13 FAST Random colours without amber 2 NO

MA14 SLOW rainbow + amber 20 5

MA15 MEDIUM rainbow + amber 10 5

MA16 FAST rainbow + amber 5 5

MA17 SLOW rainbow + amber 20 2

MA18 MEDIUM rainbow + amber 10 2

MA19 FAST rainbow + amber 5 2

MA20 Very SLOW rainbow + amber 40 NO

MA21 SLOW rainbow + amber 20 NO

MA22 MEDIUM rainbow + amber 10 NO

MA23 FAST rainbow + amber 5 NO

MA24 SLOW Random colours + amber 10 NO

MA25 MEDIUM Random colours + amber 5 NO

MA26 FAST Random colours + amber 2 NO

- TEMP:(temperature) When NTC is connected, you can see heater’s temperature in Celsius degrees. The board has an

automatic control over the led’s power, so the leds are always under the safety temperature.

Go to this submenu pushing Mode , choose TEMP with + and - and push Enter to enter in. Push Mode to get out of this

function.

- MAN: (manual mode) Function to control manually all the channels.

Go to this submenu pushing Mode , choose MAN with + and - and push Enter .

In this submenu you can choose the channel that you want to control and assign values from 0 to 255. The board run

immediately the chosen values. Dmx patch used is 13C d with 14 dmx channels and 16bit colours control, with value from 0 to

255 for each channel.

Use COMM function to put all the channel values to zero (reset).

When the board is disconnected from Main, the manual mode is reset!!

- DEF.r: (default reset) With this function you can restore all the default values.

Go to this submenu pushing Mode , choose DEF.r with + and - and push Enter and when the display shows “go?” push

another time Enter to confirm, push Mode if you don’t want to reset.

All the values will be restored to default, except the DMX address!

DMX control mode

Default mode: 7C d

CHANNEL 1: GREEN, to control the light output of the green leds, from OFF to the Max Power.

DMX value function

0 Led OFF

From 1 to 254 Proportional Light output increase

255 Led at max power

CHANNEL 2: RED, to control the light output of the red leds, from OFF to the Max Power.

DMX value function

0 Led OFF

From 1 to 254 Proportional Light output increase

255 Led at max power

CHANNEL 3: BLUE, to control the light output of the blue leds, from OFF to the Max Power.

DMX value function

0 Led OFF

From 1 to 254 Proportional Light output increase

255 Led at max power

CHANNEL 4: AMBER, to control the light output of the amber leds, from OFF to the Max Power.

DMX value function

0 Led OFF

From 1 to 254 Proportional Light output increase

255 Led at max power

CHANNEL 5: STROBE SYNC

This channel is similar to a reset, it is used to synchronized the strobe effect of more projectors.

If during strobe mode the projectors aren’t flashing at the same time they have lost synchronism, use this channel to

synchronized them again.

To activate this function just modify the dmx value of this channel, then electronic board will generate one single synchronized

pulse.

Example: During the execution of one program with Sync value 0, give a different value to the channel (example 10. The next

pulse will be given when the channel will use any values different from 10 etc…)

Andere Handbücher für IP66

Inhaltsverzeichnis

Andere Lampo Beleuchtungsausrüstung Handbücher

Lampo

Lampo SENSCRP15A Bedienungsanleitung

Lampo

Lampo SYDNEY Series Bedienungsanleitung

Lampo

Lampo SPF1LED/BN Bedienungsanleitung

Lampo

Lampo DIKLED4WBTBC Bedienungsanleitung

Lampo

Lampo SHOP 150 Bedienungsanleitung

Lampo

Lampo SYUGR28W Bedienungsanleitung

Lampo

Lampo TB Series Bedienungsanleitung

Lampo

Lampo CARR7WS Bedienungsanleitung

Lampo

Lampo REEL230V10BC Handbuch

Lampo

Lampo Fari Solar LED Series Bedienungsanleitung

Lampo

Lampo SPLED503MC Bedienungsanleitung

Lampo

Lampo HYPERCOLOR 575 Bedienungsanleitung

Lampo

Lampo IP66 Bedienungsanleitung

Lampo

Lampo Vogue 575 W Bedienungsanleitung

Lampo

Lampo LED300IP20RGBW24 Bedienungsanleitung

Lampo

Lampo SQLED Series Bedienungsanleitung

Lampo

Lampo CARR/3W Bedienungsanleitung

Lampo

Lampo FAFLAT30WRGB Bedienungsanleitung

Lampo

Lampo WLTOUCHSQ Bedienungsanleitung

Lampo

Lampo Fari Solar LED Series Bedienungsanleitung

Lampo

Lampo IP66 Bedienungsanleitung

Lampo

Lampo KITRGBWR4 Bedienungsanleitung

Lampo

Lampo IP67 LED Colour changer Bedienungsanleitung

Lampo

Lampo SYUGR20W Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung