Lantech IES-2008 Bedienungsanleitung

8 10/100TX with X-Ring Management

Industrial Switch

IES-2008

User Manual

Notice:

This manual contents are based on the below table listing software

kernel version, hardware version, and firmware version. If the switch

functions have any different from the manual contents description,

please contact the local sale dealer for more information.

Firmware Version V1.06

Kernel Version V1.00

Hardware Version A5.00

FCC Warning

This Equipment has been tested and found to comply with the limits for a

Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Content

Introduction................................................................1

Features ...................................................................1

Package Contents....................................................2

Hardware Description................................................3

Physical Dimension..................................................3

Front Panel...............................................................3

Reset Button......................................................................4

Bottom View .............................................................4

DIP-switch ................................................................4

LED Indicators..........................................................6

Ports.........................................................................7

Cabling .....................................................................9

Wiring the Power Inputs .........................................10

Wiring the Fault Alarm Contact ..............................10

Wiring the Fault Alarm Contact ..............................11

Mounting Installation...............................................12

DIN-Rail Mounting..................................................12

Wall Mount Plate Mounting ....................................14

Hardware Installation...............................................15

Network Application ................................................16

Redundant ring Application....................................16

Coupling Ring Application......................................17

Dual Homing Application........................................18

Web-Based Management ........................................19

About Web-based Management.............................19

Preparing for Web Management............................19

System Login..........................................................20

Port status ..............................................................21

Port Statistics .........................................................22

Port Control ............................................................23

Switch Settings.......................................................23

Port Mirroring..........................................................24

VLAN configuration ................................................25

Alert........................................................................32

Email Alert Configuration .................................................32

Event Configuration .........................................................33

Power Alarm Configuration..............................................35

IP Configuration......................................................35

SNTP Configuration ...............................................36

IP Security..............................................................39

RSTP Configuration ...............................................40

Redundant ring.......................................................44

QoS Configuration..................................................46

IGMP ......................................................................48

SNMP Configuration...............................................49

Security Manager ...................................................51

Configuration Backup.............................................52

TFTP Update Firmware..........................................53

Factory Default.......................................................54

System Reboot.......................................................55

Save Configuration.................................................54

Rate Control ...........................................................55

System Log ............................................................56

Troubles shooting....................................................59

Technical Specification...........................................60

Introduction

The 8 10/100TX with redundant ring Web management industrial switch is a

cost- effective solution and meets the high reliability requirements demanded

by industrial applications. The 8 10/100TX with redundant ring Web

management industrial switch can be easily managed through the Web GUI. It

also provides the redundant ring function that can prevent the network

connection failure.

Features

Conform to IEEE 802.3 10Base-T, 802.3u 100Base-TX

8-port 10/100TX industrial switch

RJ-45 port support auto MDI/MDI-X function

Wide-range redundant power design

DIN rail and wall mount design

Easy configuration design

Store-and-Forward switching architecture

Support IEEE 802.1p class of service and provide port base, Tag base and

Type of service priority method

Per port supports 4 priority queues

Support Port based VLAN / 802.1 Q Tag VLAN

Support IGMP with Query mode for multi media application

Support DHCP client

Supports ingress packet filter and egress rate limit

Support Relay alarm output for system events

Support Power polarity reverse protect

Support Port mirror for TX only, TX and RX packet

IEEE 802.3x flow control support

¾Flow control on full-duplex

¾Back pressure on half-duplex

Support Redundant ring function

Simple Network Time protocol supported

Management IP security

TFTP firmware update and system configuration restore and backup

1Mbits Embedded memory

2K MAC address table

SNMP, Web management, RMON supported

Package Contents

Please refer to the package content list below to verify them against the

checklist.

8 10/100TX with redundant ring Web management industrial switch

One DIN-Rail (attached on the switch)

One wall mount plate and six screws

User manual

8 10/100TX with redundant ring Web management User Manual

industrial switch

WallMountPlate Screws DIN-Rail

Compare the contents of your industrial switch with the standard checklist

above. If any item is damaged or missing, please contact the local dealer for

exchanging.

Hardware Description

In this paragraph, we will introduce the Industrial switch’s hardware spec, port,

cabling information, and wiring installation.

Physical Dimension

8 10/100TX with redundant ring Web management industrial switch dimension

(W x H x D) is 54mm x 135mm x 105mm

Front Panel

The Front Panel of the 8 10/100TX with redundant ring Web management

industrial switch is showed as following figure.

Front Panel of the industrial switch

Reset Button

The reset button provides user a quick and easy way to restart and set the

configuration back to default value.

Restart: press the button for 2 seconds and release.

Set to factory default value: press the button for 5 seconds and release.

The switch will set all configurations back to default setting.

Bottom View

The bottom panel of the 8 10/100TX with redundant ring Web management

industrial switch consists one terminal block connector within two DC power

inputs and one DC IN power jack.

Bottom Panel of the industrial switch

DIP-switch

The switch provides the 9 DIP-switch for configuring the relay alarm operation

mode and the ring master operation mode. The default value of Dipswitch is

OFF.

Inhaltsverzeichnis

Andere Lantech Schalten Handbücher

Lantech

Lantech IPGS-0005T-4 Bedienungsanleitung

Lantech

Lantech IPGS-5 Series Bedienungsanleitung

Lantech

Lantech Treo 500 Bedienungsanleitung

Lantech

Lantech IPES/IES-5416T Series Bedienungsanleitung

Lantech

Lantech IPES-0008A Series Bedienungsanleitung

Lantech

Lantech IES-0008-M12 Bedienungsanleitung

Lantech

Lantech IPES-0208CA-12V Bedienungsanleitung

Lantech

Lantech IPES/IES-0008B Series Bedienungsanleitung

Lantech

Lantech IES-0008B Series Bedienungsanleitung

Lantech

Lantech IGS-3208MGSFP Bedienungsanleitung

Lantech

Lantech IES-5216DF Bedienungsanleitung

Lantech

Lantech LGS-2404 Bedienungsanleitung

Lantech

Lantech IES-2208CA Bedienungsanleitung

Lantech

Lantech IES-0005B Series Bedienungsanleitung

Lantech

Lantech IPGS-5424 Bedienungsanleitung

Lantech

Lantech IES-5416DF Series Bedienungsanleitung

Lantech

Lantech IGS-2206C Bedienungsanleitung

Lantech

Lantech IPES-5408T-43 Bedienungsanleitung

Lantech

Lantech IES-3208C Bedienungsanleitung

Lantech

Lantech LGS-1104 Bedienungsanleitung

Lantech

Lantech IGS-0008A Bedienungsanleitung

Lantech

Lantech IES-2208C Bedienungsanleitung

Lantech

Lantech IPGS-5008T Series Bedienungsanleitung

Lantech

Lantech IPES-2208CA Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung