Lantech IPES-5408T Bedienungsanleitung

IPES/IES-5408T Series

8 10/100TX + 4 1000T L2+(w/8 PoE at/af) Industrial Managed

Switch w/ITU G.8032 Ring

User Manual

IP-67

IP-43

Apr. 2014

Recommendation for Shielded network cables

STP cables have additional shielding material that is used to reduce external interference. The

shield also reduces the emission at any point in the path of the cable. Our recommendation is

to deploy an STP network cable in demanding electrical environments. Examples of

demanding indoor environments are where the network cable is located in parallel with

electrical mains supply cables or where large inductive loads such as motors or contactors are

in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the

power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

Important Notice

Lantech Communications Global, Inc. reserves the right to modify the

equipment, its specification or this manual without prior notice, in the interest

of improving performance, reliability, or servicing. At the time of publication

all data is correct for the operation of the equipment at the voltage and/or

temperature referred to. Performance data indicates typical values related to

the particular product.

No part of this documentation or information supplied may be divulged to any

third party without the express written consent of Lantech Communications

Global Inc. Products offered may contain software which is proprietary to

Lantech Communications Global Inc. The offer or supply of these products

and services does not include or infer any transfer of ownership.

Interference Issues

This Equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

commercial or industrial installation. This equipment generates, uses, and

can radiate radio frequency energy. It may cause harmful interference to

radio communications if the equipment is not installed and used in

accordance with the instructions.

FCC Warning

This Equipment has been tested and found to comply with the limits for a

Class-A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy. It may cause harmful interference to radio

communications if the equipment is not installed and used in accordance

with the instructions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

Content

Chapter 1 Introduction ............................................. 7

Specification........................................................... 7

Chapter 2 Hardware Description............................ 12

2.1 Physical Dimension......................................12

2.2 Package Content: ........................................14

2.3 IP Protection................................................15

2.4 LED Indicators .............................................18

Chapter 3 Hardware Installation............................. 20

Chapter 4 Network Application............................... 25

4.1 ITU G.8032 Scheme......................................25

4.2 Ring Coupling ...............................................25

4.3 Multiple Rings ...............................................26

4.4 Dual Homing.................................................27

4.5 Chain ............................................................27

Chapter 5 Console Management ........................... 29

5.1 Connecting to the Console Port....................29

5.2 Login in the Console Interface......................29

Chapter 6 Web-Based Management...................... 31

6.1 About Web-based Management...................31

6.2 Preparing for Web Management ..................31

6.3 System Login...............................................32

6.4 System.........................................................33

6.4.1 System Identification Configuration...................... 33

6.4.2 System Information............................................... 34

6.4.3 IP configuration..................................................... 35

6.4.4 DHCP server......................................................... 36

6.4.5System Time......................................................... 38

6.4.6User Accounts –Access account management... 41

6.4.7 SNMP Configuration ........................................... 42

6.4.8 Fault Relay Configuration..................................... 43

6.4.9Digital Input /Output.............................................. 44

6.4.10Environmental Monitoring................................... 46

6.5 Event & Log................................................47

6.5.1 View Logs ............................................................. 47

6.5.2 Events................................................................... 48

6.5.3 DDM event............................................................ 49

6.5.4 Actions.................................................................. 50

6.5.5 Event Action Map ................................................. 53

6.6 Ports................................................................55

6.6.1 Configuration ........................................................ 55

6.6.2 Status................................................................. 56

6.6.3 Statistics ............................................................... 56

6.6.4 IEC Packet Statistics ............................................ 57

6.6.5 Mirroring................................................................ 57

6.6.6 Rate Limiting......................................................... 58

6.6.7 Loop Protection..................................................... 59

6.7 Power over Ethernet ......................................60

6.7.1 Configuration ........................................................ 60

6.7.2 Status.................................................................... 61

6.7.3 Detection............................................................... 63

6.7.4 Scheduling............................................................ 64

6.8 Topology..........................................................65

6.9 QoS.................................................................68

6.9.1 QoS Policy............................................................ 68

6.10 Security .........................................................70

6.10.1 MAC Address Tables.......................................... 70

6.10.2 Access Control List............................................. 71

6.10.3 IEEE 802.1X Radius Server............................... 72

6.10.4 IP Security .......................................................... 73

6.11 VLAN.............................................................74

6.11.1 802.1Q VLAN Config.......................................... 74

6.11.2 Status.................................................................. 76

6.12 MVR..............................................................76

6.12 LLDP .............................................................77

6.12.1 LLDP Configuration ............................................ 77

6.12.2 LLDP Neighbor................................................... 78

6.12.3 LLDP Statistics ................................................... 80

6.13 CDP...............................................................82

6.13.1 CDP Configuration Device Settings ................... 82

6.13.2 CDP Port Configuration...................................... 83

6.13.3. CDP Status........................................................ 83

6.14 IGMP Snooping .............................................85

6.14.1 IGMP Snooping Configuration............................ 86

6.14.2 IGMP Snooping Status....................................... 87

6.15 MSTP ............................................................89

6.15.1. MSTP Global Configuration............................... 89

6.15.2 How to enable MSTP.......................................... 90

6.15.3 CIST Settings...................................................... 92

6.15.3.1 Bridge configuration.......................... 92

6.15.3.2 Port.................................................... 92

6.15.4. MSTP MSTI Settings......................................... 93

6.15.5. MSTP Bridges Status........................................ 94

6.15.6. Bridge status of all ports.................................... 95

6.16 Aggregation................................................96

6.16.1. Aggregation Configuration................................. 96

6.16.2 LACP Port Status ............................................... 97

6.17 PTP IEEE 1588 v2.......................................98

6.18 G.8032 ERPS..............................................100

6.18.1. G.8032 Ethernet Ring Protection Configuration100

6.18.2 How to set ERPS G.8032................................. 103

6.19 Dual Homing..............................................106

6.20 Maintenance................................................108

6.20.1 Save Configuration........................................... 108

6.20.2 Config backup/restore................................... 108

6.20.3 Restart device................................................... 109

6.20.4 Firmware Upgrade............................................ 110

6.20.5 Diagnostics....................................................... 110

Appendix —SNMP OID......................................... 113

Chapter 1 Introduction

Lantech IES-5408T & IPES-5408T (IP67/IP43) series is a high performance L2+

IP67/IP43 industrial Gigabit uplink switch with 8x10/100TX + 4 GigaT (w/8 PoE at/af

injectors-IPES model)by M12 connectors which provides L2 wire speed and advanced

security function for connecting PD network. It delivers ITU G.8032 ring recovery less

than 20ms, comprehensive QoS, , IGMPv1/v2/v3 & router port, QinQ*(double tag

VLAN) , MVR (multicast VLAN registration) , LACP link aggregation and advanced

security including ACL, TACAS+*, SSH/SSL, DHCP Option 82*which are important

features required in large network. It also supports Cisco Discovery Protocol (CDP) and

LLDP for Ciscoworks to detect the switch info to be shown on L2 map topology. The

user friendly UI, innovative auto topology drawing and topology demo makes IES-5408T

& IPES-5408T (IP67/IP43) series much easier to get hands-on. The complete CLI allows

professional engineer to configure by command line.

Specification

IES-5408T series

Hardware Specification

Standards

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX

IEEE 802.3ab 1000Base T

IEEE802.3x Flow Control and Back Pressure

IEEE802.3ad Port trunk with LACP

IEEE802.1d Spanning Tree

IEEE802.1w Rapid Spanning Tree

IEEE802.1s Multiple Spanning Tree

IEEE 802.3ad Link Aggregation Control Protocol (LACP)

IEEE 802.1AB Link Layer Discovery Protocol (LLDP)

IEEE 802.1X User Authentication (Radius)

IEEE802.1p Class of Service

IEEE802.1Q VLAN Tag

Switch Architecture

Back-plane (Switching Fabric): 9.6Gbps

Packet throughput ability (Full-Duplex): 23.8Mpps @64bytes

Transfer Rate

14,880pps for Ethernet port

148,800pps for Fast Ethernet port

1,488,000pps for Gigabit port

Mac Address

16K MAC address table

Jumbo frame

10KB for 10/100TX ports

Connector

10/100TX: 8 x M12 4-pole D-coded with auto MDI/MDI-X function

10/100/1000T: 4 x M12 8-pole A-coded with auto

MDI/MDI-X function

RS-232 connector: 1 x M12 5-pole A-coded

Power Input connector : 1 x M12 5-pole A-coded

Relay contact : 1 x M12 5-pole A-coded

Network Cable

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable

EIA/TIA-568 100-ohm (100m)

100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable

EIA/TIA-568 100-ohm (100m)

1000BaseT : 4-pair UTP/STP Cat. 5E/ 6 cable

EIA/TIA-568 100-ohm (100m)

Protocol

CSMA/CD

LED

Per unit: Power 1 (Green), Power 2 (Green), P-Fail (Red)

Ethernet port: Link/Activity (Green), Speed (Green); GigaT: Link/Activity (Green)

DI / DO

1 Digital Input (DI) :

Level 0: -30~2V / Level 1: 10~30V

Max. input current:8mA

1 Digital Output(DO): Open collector to 40 VDC, 200mA

Operating Humidity

5% ~ 95% (Non-condensing)

Operating Temperature

-40°C~75°C / -40°F~167°F

Storage Temperature

-40°C~85°C / -40°F~185°F

Redundant Power Supply

Standard model:

12~72VDC

-48VDC is available for single power input

Power Consumption

Max 10W

Case Dimension

IP67 model: Aluminum case

215mm(W)x201.4mm(H)x77.6mm(D)

IP43 model: Aluminum case

203mm(W)x188.4mm(H)x77.6mm(D)

Weight

1.3kgs(IP67). 1.1(IP43)

Installation

DIN Rail** and Wall Mount Design

EMI & EMS

FCC Class A,

CE EN61000-6-2, CE EN61000-6-4, CE EN61000-4-2, CE EN61000-4-3, CE EN61000-4-4, CE EN61000-4-5, CE EN61000-4-6,

CE N61000-4-8, EN61000-4-11

Stability Testing

IEC60068-2-32 (Free fall), IEC61373 (Shock),

IEC61373 (Vibration)

MTBF

n/a

Warranty

5 years

Software Specification

Management

SNMP v1 v2c, v3/ Web/Telnet/CLI

SNMP MIB

RFC 1215 Traps MIB,

RFC 1213 MIBII

RFC 1158 MIBII

RFC 1157 SNMP MIB,

RFC 1493 Bridge MIB,

RFC 1573 IF MIB

RFC 2674 VLAN MIB,

RFC 1643 EtherLike,

RFC 1757 RMON,

RFC 2674 Q-Bridge MIB

RFC 2790 Host Resource MIB

RSTP MIB*

LLDP MIB*

Private MIB

ITU G.8032

Support ITU G.8032 v2 for Ring protection in less than 20ms for self-heal recovery < 256 switches

Support various ring/chain topologies

Ring covers data & multicast* packets

Co-exist with RSTP on different ports

User friendly UI

Auto topology drawing

Topology demo

Auto configuration for G.8032 single ring

Port Trunk with LACP

LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk members

Link aggregation to increase bandwidth

LLDP

Supports LLDP to allow switch to advise its identification and capability on the LAN

CDP

Cisco Discovery Protocol for topology mapping

VLAN

Port Based VLAN

IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096.)

GVRP (256 Groups)*,GMRP*, QinQ*

IPv6/IPv4

Present

Spanning Tree

Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree

Quality of Service

The quality of service determined by port, Tag and IPv4 Type of service, IPv4 Different Service

Class of Service

Support IEEE802.1p class of service, per port provides 8 priority queues

IP Security

Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.

Supports IEEE802.1X Authentication/RADIUS

Port Mirror

Support 3 mirroring types: “RX, TX and Both packet”

Network Security

Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.

802.1X access control for port based and MAC based authentication/MAC-IP-Port binding

Management access control with priority

256 Policy based Access Control List

SSL/ SSH for Management

TACACS+ for Authentication*

IGMP

Support IGMP snooping v1,v2,v3; Supports IGMP static route; 256 multicast groups; IGMP router port ; IGMP query

Multicast VLAN Registration

MVR enables multicast packets go through VLAN for VOD application

Bandwidth Control

Support ingress packet filter and egress packet limit.

The egress rate control supports all of packet type.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lantech Schalten Handbücher

Lantech

Lantech LPGS-2424C Series Bedienungsanleitung

Lantech

Lantech 5 10/100TX w/ 4 PoE Injector Industrial... Bedienungsanleitung

Lantech

Lantech LGS-2404 Bedienungsanleitung

Lantech

Lantech IPES-3424DSFP-2P-PT Bedienungsanleitung

Lantech

Lantech IPGS-5 Series Bedienungsanleitung

Lantech

Lantech IPES-0008B Series Bedienungsanleitung

Lantech

Lantech IPES-0104FA Bedienungsanleitung

Lantech

Lantech LGS-1104 Bedienungsanleitung

Lantech

Lantech LES-2400-RPS Bedienungsanleitung

Lantech

Lantech LES-2400-RPS Bedienungsanleitung

Lantech

Lantech IPGS-0204DSFP Bedienungsanleitung

Lantech

Lantech IES-5408T Bedienungsanleitung

Lantech

Lantech IPES/IES-0008B Series Bedienungsanleitung

Lantech

Lantech mini Switch 800 Bedienungsanleitung

Lantech

Lantech IPES-5222T Series Bedienungsanleitung

Lantech

Lantech IGS-3208MGSFP Bedienungsanleitung

Lantech

Lantech IES-2008B-DNV Bedienungsanleitung

Lantech

Lantech IPES-3408 Series Bedienungsanleitung

Lantech

Lantech IGS-0008A Bedienungsanleitung

Lantech

Lantech IPGS-0005T-4-12V Bedienungsanleitung

Lantech

Lantech IGS-0016 Bedienungsanleitung

Lantech

Lantech TPGS-L6216XT Bedienungsanleitung

Lantech

Lantech IGS-0208GSFP Bedienungsanleitung

Lantech

Lantech IES-5416T Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung