Larin METS-1 Bedienungsanleitung

LARIN



Owner’s Manual

Model METS-1

Mobile Engine Testing Station

WARNING

Read all instructions and safety warnings before operating this

equipment. Failure to follow the instructions and safety warnings

may result in personal injury or property damage.

For Customer Service Call Toll Free: 1-800-87-LARIN (1-800-875-2746)

Hours of Operation: 8:00am to 4:30pm PST

Thank you for purchasing the Larin Mobile Engine Testing Station. This product is

the result of years of research and development. It is designed to be rugged yet

lightweight and simple to use. It is a universal product, for use with most engines.

IMPORTANT: Please keep your receipt in a safe, easy to find location, as you will

need it for any warranty/repair issues that may arise.

TABLE OF CONTENTS

Important Warning/Safety Information........................................................... 1

Parts List ................................................................................................................ 2

Parts Diagram...................................................................................................... 3

Assembly .............................................................................................................. 4-7

Directions for Use ................................................................................................ 7-10

Maintenance ...................................................................................................... 11

Warranty/Replacement Parts........................................................................... 12

WARNING!

SAFETY WARNINGS AND PRECAUTIONS

1. Study, understand, and follow all instructions before operating this device.

2. Use only on hard, level surface.

3. Do NOT exceed the rated capacity of 1,000lbs for this product.

4. Any Engine Station that appears to be damaged in any way, is found to be

worn, or operates abnormally shall be removed from service immediately

until repaired. It is recommended that a manufacturer or supplier’s

authorized repair facility make necessary repairs if the manufacturer or

supplier permits repairs.

5. If it is believed that the Engine has been subjected to abnormal load, or

shock, it shall be removed from service immediately until fully inspected.

6. Assure load is centered and secured to mounting attachments before

moving or testing. Off-center loads may make the load unstable.

7. Because of potential hazards associated with this type of product, NO

alterations shall be made to the product.

8. Only attachments and/or adapters supplied by the manufacturer shall be

used.

9. Use caution when making all of the connections.

10. Follow engine testing procedures and precautions as specified by the

manufacturer’s owner’s/repair manual.

11. Failure to heed these markings/warnings may result in personal injury and/or

property damage.

Page 1 of 12

PARTS LIST Please make sure all parts are included before assembling,

Part #

Description

Qty

Part #

Description

Qty

Left Side Frame Tube

Vertical Post

Right Side Frame Tube

Dash Panel

Rear End Frame Tube

Vertical Post

Cross Member Frame Tube

Vertical Post

Cross Member Frame Tube

Horizontal Bar

Front End Frame Tube

Engine Support

Swivel Caster

Engine Support

Swivel Caster

Engine Support

Rigid Caster

Engine Support

Rigid Caster

Gas Tank Holder

Black Sleeve

Gas Tank Holder

Black Sleeve

Large Bolt

Black Sleeve with Post

Medium Bolt

Black Sleeve with Post

Long Bolt

Black Sleeve with Post

Medium Bolt

Black Sleeve with Post

Small Bolt

Threaded Rod

Small Bolt

Threaded Rod

Support Strap

Tray Support

Support Strap

Tray

Gas Tank

Vertical Post

Page 2 of 12

PARTS DIAGRAM 1

PARTS DIAGRAM 2

Bolts included. Please refer

to this diagram during

assembly.

Page 3 of 12

ASSEMBLY

Tools Needed for Assembly:

Crescent Wrench

Phillips Screwdriver

13mm Wrench

14mm Wrench

17mm Wrench

19mm Wrench

For all of the following steps, please refer to Parts Diagram, Parts List and Illustrations.

STEP 1 Unpack Testing Station and verify that you have received all of the

parts as indicated on the parts list.

STEP 2 Place Left Side Frame Tube and Right Side Frame Tube (#1 and #2)

on the floor with the 6 holes on the top and matching. Make sure

that the holes are closer to the outer edge of the metal parts and

that the two holes on the sides are closer to the top than to the

bottom. See Illustration A.

STEP 3 Attach Swivel Casters (#7 and #8) to Front End Frame Tube (#6)

using four of the small bolts (#38), two for each caster.

STEP 4 Attach Rigid Casters (#9 and #10) to Rear End Frame Tube (#3)

using four of the small bolts (#38), two for each caster.

STEP 5 Place Cross Member Frame Tube (#5) on the floor. Slide the Black

Sleeve with Post (#14) onto the Cross Member Frame Tube (#5).

Next slide another Black Sleeve with Post (#13) onto the Cross

Member Frame Tube (#5). Next insert the Black Sleeve (#12) into

the end of Cross Member Frame Tube (#5) as shown in Illustration B.

Illustration A

Page 4 of 12

ASSEMBLY CONTINUED

STEP 6 Place the other Cross Member Frame Tube (#4) on the floor. Slide the

Black Sleeve with Post (#15) onto the Cross Member Frame Tube

(#4). Next slide another Black Sleeve with Post (#16) onto the Cross

Member Frame Tube (#4). Next insert the Black Sleeve (#11) into the

end of Cross Member Frame Tube (#4) as shown in Illustration B.

STEP 7 Slide Cross Member Frame Tube (#4) onto Left and Right Side

Frame Tubes (#1 and #2). Next slide the other Cross Member Frame

Tube (#5) onto the Left and Right Side Frame Tubes (#1 and #2) as

shown in Illustration C.

STEP 8 Insert both large bolts (#33) into holes of Front End Frame Tube (#6).

Next screw them into the ends of the Threaded Rods (#17 and

#18). See Illustration C.

STEP 9 Slide the Threaded Rods (#17 and #18) into the ends of Left and

Right Side Frame Tubes (#1 and #2). Make sure it is the side that has

three holes. See Illustration C.

STEP 10 Place Rear End Frame Tube (#3) onto the ends of the Threaded

Rods (#17 and #18) at the opposite end of Left and Right Side

Frame Tubes (#1 and #2). Fasten with nuts and washers.

Illustration B

Page 5 of 12

ASSEMBLY CONTINUED

STEP 11 Using long bolt (#35), attach Swivel Casters (#7 and #8) to Left and

Right Side Frame Tubes (#1 and #2). Fasten with nuts and washers.

Next, also using the long bolt (#35), attach Rigid Casters (#9 and

#10) to Left and Right Side Frame Tubes (#1 and #2) on opposite

end. Fasten with nuts and washers.

STEP 12 Place the Vertical Posts (#21 and #22) onto the vertical posts on

the Front End Frame Tube (#6). Attach the Support Straps (#39 and

#40) to the Left and Right Side Frame Tubes (#1 and #2) using the

long bolts (#35).

STEP 13 Place the remaining Vertical Posts (#24 and #25) over the vertical

posts of the attached Black Sleeves with Posts (#15 and #16).

Attach with small bolt (#37).

STEP 14 Place two of the Engine Support (#29 and #30) onto vertical posts

of the attached Black Sleeves with Posts (#13 and #14). Attach

with small bolt (#37).

Page 6 of 12

ASSEMBLY CONTINUED

STEP 15 Place Horizontal Bar (#26) on top of Vertical Posts (#24 and #25).

Attach with medium bolt (#36).

STEP 16 Place Engine Supports (#27 and #28) onto Horizontal Bar (#26).

Attach with medium bolt (#34).

STEP 17 Place Dash Panel (#23) on top of Vertical Posts (#21 and #22).

Attach with medium bolts (#36).

STEP 18 Attach Tray Support (#19) to Left and Right Side Frame Tube (#1

and #2) using long bolts (#35). Place Tray (#20) on top of Tray

Support (#19) and Front End Frame Tube (#6).

STEP 19 Attach Gas Tank Holders (#31 and #32) using long bolts (#35).

STEP 20 Slide Gas Tank (#41) into Gas Tank Holders (#31 and #32).

DIRECTIONS FOR USE

1. The owner and/or operator shall read, study, understand and follow all

product warnings/cautions and instructions prior to use. If the operator

is not fluent in English, the product warnings/cautions and instructions

shall be read to and discussed with the operator in operator’s native

language by purchaser/owner or his designee, insuring that the

operator comprehends their content.

2. Use caution when loading and unloading.

3. WARNING: Center load.

4. Surfaces must be dry, clean and free from oil or grease.

5. Secure the motor to the Testing Station as instructed.

6. WARNING: Because of potential hazardous associated with this type of

equipment, NO ALTERATIONS SHALL BE MADE to this product for use.

7. WARNING: Only attachments and/or adapters supplied by the

manufacturer shall be used.

8. Follow diagrams of Figure 1, Figure 2, Figure 3, Figure 4 and Figure 5.

Page 7 of 12

WIRING SYSTEM A-33

FIGURE 1

Attach home sized garden

hoses to water adapters.

Thermostat is NOT used, and

the water pump remains

stationary (not spinning). It is

important to run the water

in the correct direction,

otherwise hot spots may

occur inside the engine and

possible damage. Start with

a small amount of water.

Watch the temperature

gauge, regulate to 160, 170,

180, as necessary.

Turn water off IMMEDIATELY

upon turning the engine off.

Thus, eliminating the risk of

cracking the hot block or

heads with cold water

entering the engine. Let

engine cool down by itself.

Intake Manifold

Flow

Radiator Hose

and Clamps

Water Pump

Flow

Radiator Hose

and Clamps

Water

Outlet

Water

Inlet

INLET ADAPTER

(Not Included)

OUTLET ADAPTER

(Not Included)

Page 8 of 12

FIGURE 2

Fuel

Tank

Battery

To Engine

Fuel System

Fuel

Pump

Fuel Filter

Ford &

Chrysler

Starter &

Solenoid

Distributor

Ballast

Resister

Coil

On/Off

Power

Switch

Starter

Button

BLK RED

BLK GRN

TEMP

GAUGE

TACHOMETER

OIL PRESSURE

GAUGE

RED

NOTE

Ballast resister cuts battery

voltage down to about 7 volts

for long point life. If you need

12 volts either eliminate or

bypass resister.

NOTE

Most parts houses have in line

universal type fuel pumps that

are about the size of an in line

fuel filter and make for a nice

installation.

NOTE

Use radiator hose clamps to clamp

fuel pump, coils and ballast resister

to the legs of the bow under the

panel with weather stripping in

between the two.

Page 9 of 12

Andere Handbücher für METS-1

Inhaltsverzeichnis

Andere Larin Prüfgeräte Handbücher

Larin

Larin METS-1 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung