Larson Electronics IND-RL-HDB-BX9-120V Bedienungsanleitung

IND-RL-HDB-BX9-120V

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1of 3

9W Rechargeable UVC Handheld Surface Sanitizer

Aluminum - 8 Hour Runtime

Instruction Manual

Thankyou for your purchase of the Larson Electronics IND-RL-HDB-BX9-120V.

EPA Reg. No 98409-1

EPA Est. No. 98409-TX-1

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE IND-RL-HDB-BX9-120V MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

Never place spotlight face down when light is on. Doing so could burn/ignite surfaces such as seats, carpeting, etc. and

cause major property damage. Always turn spotlight off when not in use.

Avoid direct eye exposure the light source when light is on. DO NOT shine light into the face of someone else.

DO NOT touch lens of light when on or recently on. The lens/cooling fins will be hot after long periods.

DO NOT allow children to handle or operate this light.

DO NOT use this product for other than its intended use.

DO NOT operate in close proximity of combustible or flammable materials.

DO NOT attempt to operate this light if cord, plug, battery, lens or any part of the light is damaged or corroded.

WARNING:

USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OFTHIS DEVICE. THIS LINE

CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT

READILY AVAILABLE.

IMPROPER USE OFTHIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES ORDEATH TO

PERSONNEL.

PERIODIC INSPECTION OF THE CORD IS NECESSARY.

THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,

THE CORD MUST BEREPLACED BEFORE RESUMING USE.

UV Warning

WARNING: ULTRAVIOLET LIGHT IS HARMFUL TOEYES AND SKIN. DO NOT STARE DIRECTLY INTO THE ULTRAVIOLET

BEAM WITHOUT WEARING PROTECTIVE GEAR TOPROTECT EYES FROM LONG TERM DAMAGE. UNPLUG LAMP BEFORE

SERVICING.

IND-RL-HDB-BX9-120V

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2of 3

The Larson Electronics IND-RL-HDB-BX9-120V is a Portable UVC Handheld Surface Sanitizer which can disinfect 99% of

viruses, bacteria, mold and spores on surfaces, work stations, tables and desks, as well as devices, machines and

personal equipment. This battery-powered unit offers UV-C output at a range of 200nm - 280nm (253.7nm) and comes

equipped with a 9-watt UV fluorescent lamp. The aluminum UV system has a 10aH lithium-ion battery pack and a handle

for up close UV light treatment.

WIRING

Warning: Check product label for correct input voltage!

Standard Cord Cap

This unit comes pre-wired from factory with the selected cord cap. Take

precautionary steps for weatherproofing all connections if installed in a

location where water may come in contact with the unit. All outdoor

installations and indoor installations near a wet location require the use of a

GFCI device for safety, according to the National Electrical Code® (NEC).

Ensure the unit is properly grounded.

CHARGING

This unit is powered by a 10aH lithium-ion battery pack. Charging is facilitated by an included wall charger that operates on

120V AC. It takes approximately 2 hours to fully charge the battery. At full charge, the battery offers 8 hours of runtime.

MOUNTING

The IND-RL-HDB-BX9-120V has a handle at the back of the unit for portable use. This lightweight design allows the device

to be held directly over the target surface or object with ease.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The IND-RL-HDB-BX9-120V is designed to provide years of reliable performance. Should the need for replacement parts

arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

IND-RL-HDB-BX9-120V

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 3of 3

Ultraviolet Radiation Safety

WARNING: Do not attempt operation until you are familiar with all warnings,precautions,and procedures outlinedwithin

thisinstruction sheet.

OPERATION PRECAUTIONS

•UV LIGHT WARNING: UV-C light can cause temporary or permanent loss of vision, and temporary acute

redness or ulceration (mild to severe sunburn) to exposed skin. To prevent exposure, do not operate the device

in any application that allows UV-C light to be visible during operation.

•UV LIGHT CAUTION: UV light may degrade plastic and rubber components after longterm exposure.

•Currently, there are no work place related rules and regulations that are set by OSHA (Occupational Safety and

Health Association) in regard to UVC environmental health and safety.

•NEVER LOOK DIRECTLY AT THE BULB OR DISINFECTING TARGET ZONE

OPERATION SAFETY

•People and animals are forbidden from being exposed to the light output of this light for extended periods of

time. Long term exposure will case damage to the eyes and skin.

•This product produces UV radiation. Anything in front of the unit will be exposed to UV radiation. Operators

positioning the light while not illuminated will not be exposed. Radiation is only emitted while the light is turned

on. Radiation will not linger in the environment when the lamps have been powered off. Safety equipment is only

required when the device is in-use.

•Wear eye protective gear when operating the equipment. Polycarbonate safety glasses at minimum are required

during all operations. Full frontal polycarbonate or UV-preventative face masks are recommended.

•Wear long sleeves and gloves when operating the equipment. Personal protective gear is required for long term

exposure.

These safety precautions will help ensure service personnel are protected from accidental exposure while maintaining

the effectiveness of UV-C to eradicate biological contaminants.

In the event of UV exposure, the following actions are recommended.

OPERATION SAFETY STRATEGIES

•Instruct service personnel to never look directly at UV-C light without adequate eye protection.

•Make it a policy to never enter areas being disinfected with UV lighting systems without powering the system

down first. Methods of powering down depends on the options of the device purchased and may include

unplugging the light source, operating the power switch to power the lamps off, or turning the system off via a

wireless remote control or wireless application.

•Place warning labels near all openings/entrances to areas being disinfected with UV lighting systems. When

possible, lock access doors to prevent unexpected guests from entering the area.

•Close blinds/curtains of areas being disinfected with UV lighting systems if available. If not available, block off

direct access to windows/doorways to prevent access to the area. If you cannot fully block off all access

(hallways with visible windows, etc) place exterior warnings in areas prior to the exposed windows (hall

pedestals, banners, posters) explaining what areas are being disinfected and to not look into the room.

•Educate non service personnel about the intended operations for UV disinfecting and what signage will be

posted. Instruct non service personnel to never look directly at UV-C light.

•Instruct service personnel to always wear personal protective gear (as outlined above) when they must operate in

an area that has UV-C exposure, for short or long term work.

•See an ophthalmologist if eye damage is suspected.

•Treat skin lesions immediately.

•For severe skin lesions, seek local medical treatment and follow their recommendations for treatment.

•Follow your organization’s incident reporting procedure. These often require documentation of the date and

time of the incident, persons involved, equipment involved and type of injury.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics GL-2051-M Bedienungsanleitung

Larson Electronics

Larson Electronics LEDWL-5-M Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-QC-16C-2X150LED-RT-X24V-C1D1-12.3-100-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics VPLHL-7WLED-GR30 Bedienungsanleitung

Larson Electronics

Larson Electronics PTB-1-75FT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-QC-16C-1X150LED-RT-100-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-50LED-100 Bedienungsanleitung

Larson Electronics

Larson Electronics LED10W-1X4LT Bedienungsanleitung

Larson Electronics

Larson Electronics C1D2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-FL1524-50-1523 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLX-SL-PT-3X80W.RD2-TRC-20X-100C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-QP-2X50LED-RT-100 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-2051-F-M Bedienungsanleitung

Larson Electronics

Larson Electronics TPM-GL20004-12C-1227-10C Bedienungsanleitung

Larson Electronics

Larson Electronics LM-25-3S-EW-THM-12VDC Bedienungsanleitung

Larson Electronics

Larson Electronics SLEDB-110V-MS Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-LI-48-2X50LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-DLC Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-BS-70-100 Handbuch

Larson Electronics

Larson Electronics GL-9051-F-M Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-50LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-LED-150W-RT-SS-HC Bedienungsanleitung

Larson Electronics

Larson Electronics EPP-3P4W-30A-N7 Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung