LauraStar Magic Evolution Bedienungsanleitung

IMPORTANT SAFEGUARDS

When using your flatiron, basic safety precautions should always be followed, including the

following: READ ALL INSTRUCTIONS BEFORE USING

1. Use iron only for its intended use. 2. To protect against a risk of electric shock, do not

immerse the iron in water or other liquids. 3. The iron should always be turned to off before

plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp

plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let iron cool completely

before putting away. Loop cord loosely around iron when storing. 5. Always disconnect iron

from electrical outlet when filling with water or emptying and when not in use. 6. Do not

operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk

of electric shock, do not disassemble the iron, take it to a qualified service person for

examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron

is used. 7. Close supervision is necessary for any appliance being used by or near children. Do

not leave iron unattended while connected or on an ironing board. 8. Burns can occur from

touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside

down. 9. If you notice any malfunction, disconnect the power supply and don’t attempt to repair

the appliance, but contact the Customer Service Center 10. WARNING! Risk of burns! After

unplugging the iron, allow it to cool for at least 2 hours before unscrewing the DRAIN cap for

rinsing.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high wattage appliance on the same

circuit. 2. If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords

rated for less amperage may overheat. Care should be taken to arrange the cord so that it

cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

Operating

Instructions

English

10/2002 (USA) Art. N° 504.0600.723

Español

Français

Magic Evolution Anglais USA 27.11.2003 14:24 Page 1

• Important Safety Precautions 1

• Installation 2

• Preparing to use your appliance 3

• Starting to use your appliance 4

• Ironing 5

• Hints for use 5

• Refilling 7

• Maintenance 8

• Storage 9

• Technical data 9

• Problems/Solutions 10

• Customer services 11

• International Guarantee 12

• Warranty card 12

Contents

Dear customer

Thank you and congratulations

Thank you for showing confidence in our company and congratu-

lations for choosing LauraStar TM Magic Evolution. Properly used

and maintained, this system will give you years of dependable

service.

However, it is important that you read this manual completely

before using your LauraStarTM Magic Evolution system. This gar-

ment care system is for home use only.

This system uses steam and heat, so many parts of the system

can cause burns when in use. These hot parts will be labelled in

this manual with the following symbol:

Additional warnings

Please pay particular attention to the important safety tips.

Additional warnings for your safety and cautions to prevent dam-

age to the system are included throughout this manual. These are

indicated by:

Description

Table

iron

operating instructions

wheels (optional)

cord-holder

silicone mat

Softpressing soleplate

bottle

drain receptacle

boiler

iron switch

boiler switch

green pilot light

drain cap

filling cap

plug

cable

iron basket

iron rest

motor

motor cable

thermostat

steam button

monotube

WARNING CAUTION

English

LauraStar ™ Magic Evolution

cover

Magic Evolution Anglais USA 27.11.2003 14:24 Page 2

IMPORTANT SAFEGUARDS

When using your flatiron, basic safety precautions should always be followed, including the

following: READ ALL INSTRUCTIONS BEFORE USING

1. Use iron only for its intended use. 2. To protect against a risk of electric shock, do not

immerse the iron in water or other liquids. 3. The iron should always be turned to off before

plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp

plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let iron cool completely

before putting away. Loop cord loosely around iron when storing. 5. Always disconnect iron

from electrical outlet when filling with water or emptying and when not in use. 6. Do not

operate iron with a damaged cord or if the iron has been dropped or damaged. Toavoid the risk

of electric shock, do not disassemble the iron, take it to a qualified service person for

examination and repair.Incorrect reassembly can cause a risk of electric shock when the iron

is used. 7. Close supervision is necessary for any appliance being used by or near children. Do

not leave iron unattended while connected or on an ironing board. 8. Burns can occur from

touching hot metal parts, hot water,or steam. Use caution when you turn a steam iron upside

down. 9. If you notice any malfunction, disconnect the power supply and don’tattempt to repair

the appliance, but contact the Customer Service Center 10. WARNING! Risk of burns! After

unplugging the iron, allow it to cool for at least 2 hours before unscrewing the DRAIN cap for

rinsing.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not operate another high wattage appliance on the same

circuit. 2. If an extension cord is absolutely necessary,a 15-ampere cord should be used. Cords

rated for less amperage may overheat. Care should be taken to arrange the cord so that it

cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

Operating

Instructions

lish

10/2002 (USA) Art. N° 504.0600.723

añol

Fran

ais

English

Magic Evolution Anglais USA 27.11.2003 14:24 Page 3

1. Use ONLY for Ironing Following These Operating Instructions.

The Iron Uses HOT SURFACES. Contact with Hot Surfaces Can

Cause Severe Bruns or Damage to Nearby Objects.

3. The Iron Uses PRESSURIZED STEAM. DO NOT OPEN the Filling Cap

Except as Instructed on Page 3 of This Manual. Contact with the

Pressurized Steam Can Cause Severe Scalding.

4. Never iron clothes while you are wearing them.

5. Keep Out of Reach of CHILDREN During Use and Storage. DO NOT Leave

Iron Unattended During Use.

6. TURN OFF and Then Unplug When Not in Use or When Filling/Emptying

Boiler.

7. INSPECT Electrical Cord and Steam Tube Weekly for any Fraying or

Damage; DO NOT USE with Damaged Cord or Monotube.

8. DO NOT Attempt to Repair or Service Components.

DO NOT USE Near Water or Other Liquids to Avoid the Possibility of

Electrical Shock.

10. To Unplug, Grip the Plug Firmly and Remove it from the Wall Socket;

DO NOT Pull on Cord.

11. Do not introduce objects into the ventilator cage. The protective grid of the ven-

tilator is built to withstand only normal use and does not protect against the voluntary

introduction of objects. Mind the children!

12. The Main Electrical Cable and Monotube Must Not be Allowed to

Come into Contact with Hot Surfaces.

13. To avoid the accumulation of water in the board, never iron when the

motor cable is unplugged.

14. ONLY Use in Well Lighted Area.

15. ALWAYS Use in Well Grounded Electrical Outlet.

16. DO NOT Use Boiler Without Water.

Please read the following safety measures carefully and keep them along with the

operating instructions of your other appliances. Please repeat the safety measures to

all new users of your appliance.

Important Safety Precautions

10.

11.

12.

13.

HOT

English

Magic Evolution Anglais USA 27.11.2003 14:24 Page 4

• Cord-holder: 6

Slide on to the table like indicated in the drawing (p.II).

• Silicone mat: 7

This mat is built to withstand a hot iron. Do not place the iron on any

other surface.

• Iron rest: 20

Clip the iron rest on the iron basket as indicated in the drawing. It

is built to withstand a hot iron.

• Wheels: 4

Optional.

The cover

Slide the cover from back to

front. Turn it down under the tip

of the board. The system is sup-

plied with a special cover. It has

a special lining which allows

vacuum and blowing to be uni-

form over the whole table. To

obtain a new cover, contact your

customer service agent. The

cover may be washed at 30°, no

spinning.





The accessories

The table

1. Place the board vertically on the ground. 2. Lift the table top and hold it in one hand. 3. With the other

hand slide the adjustment device (under the board) up to whichever of the three stop bars corresponds

to your height.

Pull the iron basket from beneath the table by sliding it outwards.

Installation

ALWAYS Place Hot Iron on Silicone Mat or on Iron Rest When Not

in Use. DO NOT Place Hot Iron on Any Other Surface.

CAUTION

Do not use any other cover as it

would seriously reduce the

effectiveness of the vacuum and

blowing functions.

CAUTION

English

Magic Evolution Anglais USA 27.11.2003 14:24 Page 5

Première utilisation

Appliance unplugged Rinsing the boiler

Fix the board in the highest

position. Put the rinsing recep-

tacle beneath the boiler.

Unscrew the drain cap.

Unscrew the filling cap. Pass

the contents of a bottle of tap

water through the boiler to rinse

it. Screw the filling and the drain

cap back on again.

Filling the boiler

1.Unscrew the filling cap.

2. Fill the boiler with water using the bottle provided: it has an anti-overfill device which stops the flow

when the boiler is full (the capacity of the bottle is greater than that of the boiler).

Squeeze the bottle briefly to start the filling of the boiler. Once full, screw the filling cap back on again as

far as it will go.

Preparing to use your appliance

CAUTION

Always remove the mains

plug from the socket before

filling the boiler.

ALWAYS Unplug Electrical Cord Before Filling the Boiler

For refilling while ironing,

please follow the instructions

on page 7!

WARNING

English

For further rinsing, follow instructions on page 8!

Fill up the boiler before every use.

What sort of water?

If your tap water is soft or medium (equal or less than 18°f/11°d/1.8mmol/l), you may use your tap water.

If it's not the case, we advise you to mix it with industrial standard demineralised water: 1/3 tap water -

2/3 demineralised water.

To find out the exact hardness of your tap water, contact your local authorities or water company.

Never use additives (ex. perfumed water) deionizised water or water softened with salt, neither distilled

water, nor recovery water from the linen-drier, as these products are detrimental to the good quality of the

steam.

Magic Evolution Anglais USA 27.11.2003 14:24 Page 6

Switches

1. Push the plug into the socket. 2. Switch on Boiler and Iron

switches and wait for the green

steam light (about 8 to 10 min-

utes).

Starting to use your appliance

Always refill the boiler before ironing. If the boiler heats up without water, you

could damage it. Using the appliance with no water in the boiler invalidates your

warranty.

The green steam indicator light illuminates when the

appliance is ready for use.

CAUTION

English

Setting of the iron temperature

This dial only regulates the temperature of the iron soleplate. We recom-

mend that you iron all materials at the same temperature (zone •••). Test

your iron on a rag before commencing ironing. If the iron spurts water,

slightly increase the temperature. If no steam is seen coming out of the iron

reduce the temperature slightly.

After a change of setting it takes about 2 min

for the new temperature to stabilize.

Steam button

Before starting to iron, give 3

bursts of steam to eject water

condensed in the tube, then test

your iron on a piece of material.

If it still spits water increase the

temperature slightly.

CAUTION

Magic Evolution Anglais USA 27.11.2003 14:24 Page 7

Blowing – vacuum & choice of 2 speeds

A single steam button situated on the iron allows you to both start the emission of steam and switch from

“blowing” mode to “vacuum” mode (or vice versa).

Changing from one mode to the other can be done only when the motor is off. The chosen mode stops

automatically at the end of a cycle (lasts 4 seconds). At that moment you may select the desired mode.

In addition to the vacuum and blowing functions, the steam button 24 enables the strength of the airflow

from the ventilator to be regulated. When the iron is switched on, the ventilator is pre-set to maximum

capacity (100%). Changing from one mode to the other can be done only when the motor is off. To change

to reduced airflow (50%), press the steam button twice very quickly. To go back to maximum airflow, press

the steam button twice again.

Blowing

A very short press (less than half a second) on the steam button starts the “blowing” mode. When blow-

ing mode is chosen, each press of the button to give steam restarts the cycle (lasts 4 seconds).

Vacuum

A long press (more than one second) on the steam button starts the “vacuum” mode. Vacuum is engaged

at every emission of steam and stops 4 seconds after the end of the jet of steam to guarantee optimum

drying of the fabric.

When vacuum is being used each press on the button to give steam restarts the cycle (lasts 4 seconds).

Ironing

Hints for use

Why have blowing and vacuum?

To improve the quality of ironing and increase the autonomy of your appliance, steam iron the material first

and then re-iron it without steam, in order to dry the material.

Perfect ironing requires steam to be injected into the fabric. This is a requirement for the complete removal

of creases. For this, the Laurastar™Magic Evolution system uses the same methods as for professional dry

cleaning: vacuum and blowing.

Angora/Wool

• Steam iron about 4 in. from the surface of the material to avoid damage.

• Shake the garment by hand so that it regains its normal shape.

English

• • • • ••• • •

blowing

vacuum

Velvet

Back Buttons Welt Legs Inside Sleeves Buttons Top Pleats

and collar and creases and lining and collar

Magic Evolution Anglais USA 27.11.2003 14:24 Page 8

Using the Softpressing soleplate

The Softpressing soleplate must be used for dark materials that are likely to become shiny and synthetic

materials that might stick to the soleplate.

To use the Softpressing soleplate:

1. Place the iron in the soleplate.

2. Pull the spring towards the end of the iron as shown in the drawing. Wait for about 2 minutes for the

soleplate to reach the same temperature as the iron. This avoids droplets of condensation falling onto the

material. ALWAYS remove the Softpressing soleplate after use.

Silk

Vertical removal of creases

Hang the garment on a coat

hanger or hold it up.

With a sweeping movement from

top to bottom, lightly touch the

material while giving short bursts

of steam.

Note: It is easy to remove creas-

es from most materials, except

for cotton, linen and some silks.

If it is difficult to remove the

creases from a material, iron it as

normal on the ironing board.

Special materials

•Velvet

•Corduroy

•Jersey

If you are not using the

Softpressing soleplate, steam

iron 1-2 in. from the surface of

the material, then finish by hand.

Steam iron silk in the normal

way.

In the case of dark silk you are

advised to use the Softpressing

soleplate.

HOT

Make sure the Softpressing soleplate does not touch mohair, cashmere, velvet and

angora! Iron these materials at a distance.

•Contact with the Softpressing soleplate can cause severe burns and damage nearby

objects.

•Misusing a hot iron with steam under pressure can cause severe burns.

WARNING

CAUTION

English



Magic Evolution Anglais USA 27.11.2003 14:24 Page 9

Refilling while ironing

6. Now unscrew the filling cap

completely and refill as shown

on page 3.

5. Unscrew the filling cap slowly

until you hear or see the steam

escaping -about 2 turns- and

wait until residual steam has

totally escaped. Use a cloth to

avoid direct contact with the

steam.

4.And unplug the device.

3. Turn off the iron switch (12).

2. Press the steam button and

hold it down until no more steam

is emitted. Direct iron away from

your body or others.

1.Turn off the boiler switch (13).

Low water indicator

A buzzer goes off when the water in the boiler drops to the minimum

level.

Please refer to the chapter below for refilling while ironing.

Refilling

•The Iron Uses PRESSURIZED STEAM. DO NOT OPEN the Filling Cap Except as

Instructed below. Contact with the Pressurized Steam Can Cause Severe Scalding.

•TURN OFF and Then Unplug When Not in Use or When Filling / Emptying Steam

Generator.

WARNING

English

Magic Evolution Anglais USA 27.11.2003 14:24 Page 10

Andere Handbücher für Magic Evolution

Inhaltsverzeichnis

Sprachen:

Andere LauraStar Eisen Handbücher

LauraStar

LauraStar Magic I-S5 Bedienungsanleitung

LauraStar

LauraStar SMART Bedienungsanleitung

LauraStar

LauraStar Magic Evolution Bedienungsanleitung

LauraStar

LauraStar BORK i810 Bedienungsanleitung

LauraStar

LauraStar MAGIC i-S6 Bedienungsanleitung

LauraStar

LauraStar Magic Evolution 723 Bedienungsanleitung

LauraStar

LauraStar Compact Bedienungsanleitung

LauraStar

LauraStar Magic I-S5 Bedienungsanleitung

LauraStar

LauraStar S4a Bedienungsanleitung

LauraStar

LauraStar STEAMUPi-G5 740 Bedienungsanleitung

LauraStar

LauraStar LIFT Bedienungsanleitung

LauraStar

LauraStar X1 766 Bedienungsanleitung

LauraStar

LauraStar First G1731 Bedienungsanleitung

LauraStar

LauraStar LIFT Bedienungsanleitung

LauraStar

LauraStar MAGIC i-S5 750 Bedienungsanleitung

LauraStar

LauraStar GO Bedienungsanleitung

LauraStar

LauraStar S6a 765 Bedienungsanleitung

LauraStar

LauraStar EVOLUTION G4 Bedienungsanleitung

LauraStar

LauraStar STEAMAX G2 735 Bedienungsanleitung

LauraStar

LauraStar SMART Bedienungsanleitung

LauraStar

LauraStar S7 775 Bedienungsanleitung

LauraStar

LauraStar S4e Bedienungsanleitung

LauraStar

LauraStar S7 Bedienungsanleitung

LauraStar

LauraStar PRO Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung