LCN 9700 Series Bedienungsanleitung

740100-00(5)

121 West Railroad Avenue

Princeton, IL 61356-0100

1-800-526-2400

FAX: 800-248-1460

www.lcn.ingersollrand.com

LCN

Middle Swing Control Box

2900 Series, 9700 Series

Installation Instructions

Senior Swing Control Box

2800 Series, 9500 Series

740100-00

Page2of14 740100-00(5)

IMPORTANT

Theseinstructionsarepresentedinstep-by-stepsequence.Itisveryimportantthat

installation begins with “1. Pre-Installation Site and Product Check” (page 3) and

continues as directed after each section.

WARNINGS

Alwaysdisconnectmainpowerto the operator prior to replacing.

Controlboxcontainsnoserviceablepartsinside.

TheMiddleandSeniorSwingControlBoxesareforusewiththeMiddle and Senior Swing Power Operator

Systems, respectively. The systems can operate a single door (2810, 9530, 9540, 2910, 9730, and 9740

Series),asimultaneouspairofdoors(2850,9550,2950,and9750Series),oranindependent pair of doors

(2860,9560,2960,and9760 Series).

ANSI/BHMA A156.19 Compliance

TheMiddle and Senior Swing PowerOperator Systems are low energy productsand mustconform tothelatest

versionofANSI/BHMAA156.19(AmericanNational StandardforPowerAssistandLow EnergyPowerOperated

Doors).

InstallationInstructions

Allinstallationinstructionsarevaluablereferencesandshouldbegiventothebuilding owner or maintenance

supervisorafterinstallationiscomplete.

The Middle and Senior Swing Control Box installation instructions and the manufacturer’s instruction manual

accompanyinganysensormustbereferencedtoensureproperinstallation,setup,andoperation.

CONTENTS

GeneralInformation ..................................................................................................................................... 2

ElectricalSpecifications .............................................................................................................................. 3

Pre-InstallationSiteandProductCheck ...................................................................................................... 3

Installation................................................................................................................................................... 4

Wiring ......................................................................................................................................................... 4

KeypadSettings ......................................................................................................................................... 8

System Test...............................................................................................................................................12

Troubleshooting..........................................................................................................................................13

Releasefor Service ....................................................................................................................................14

GENERAL INFORMATION

740100-00(5) Page3of14

ELECTRICAL SPECIFICATIONS

ACinputvoltage .....................................................120VAC

ACfuse..................................................................120 VAC, 2.5Atime-delay fuse

Motorprotection .....................................................Solidstatefailuredetectionandshutdown

Activateinputs .......................................................dry NO contacts (close contacts to open door)

Safetyinputs..........................................................dry NO contacts (closed contacts indicate an obstruction)

Breakawayinput ....................................................dry NC contacts (open contacts indicate breakaway)

3-positionswitchinput............................................dry 3-position switch

PowerBoostdisableinput......................................dry NO contacts (close contacts to disable Power Boost

Lock output ............................................................Form C dry relay contacts rated 8A, 30 VDC maximum

Accessorypoweroutput.........................................24 VAC, 1.5A(protected by resettable thermal fuse)

Logicpoweroutput .................................................5 V, 50 mA(protected by resettable thermal fuse)

1. PRE-INSTALLATION SITE AND PRODUCT CHECK

1.1. All required installation steps listed before “8. Control Box Installation” in theAstro/Middle/Senior

Swinginstallationinstructions(partNo.740132-00)shouldbecompleted before installing the

Middle/SeniorSwingcontrolbox.

1.2. Check that the control box model (indicated on control box label; Figure 1-1) is correct for the application.

1.3. CheckthattheavailableACvoltagematches the controlboxvoltagerequirement(120VAC).

1.4. Checkthat all accessories required for the applicationare on hand.

IMPORTANT

Type WidthperLeaf MaximumWeightperLeaf

SingleDoor 36”to48” 200lb.

SimultaneousPair 30”to48” 200lb.

Factory Authorized Door Leaf Size and Weight

Figure 1-1

Labelindicatesmodel

CAUTION: 120VAC

2.5ATIME-DELAYFUSE

WARNING: FOR CONTINUED

PROTECTIONAGAINSTFIRE,

REPLACEONLYWITH SAME

TYPEAND RATINGOFFUSE.

COMPANION

MOTOR

COMPANION MASTER

SPEED

TCLOSE

SPEED

: OPENINGSPEED

:BACKCHECKSPEED

:BACKCHECKPOS.

: HOLD-OPEN DELAY

:LATCH POSITION

:AUTO-REV. CLOSING

:ELECTRIC LOCK

:POWERBOOST

:PUSH‘N’GO

:ALTERNATEACTION

:SAFETYSLOW/STOP

:SLOWDOWN DISABLE

:RESERVED

SETTING VALUE

DEFAULT

POWER

DOWN

WARNING: ALL SPEED

SETTINGS(OPENING,

CLOSING,ANDLATCHING)

ANDHOLD-OPENTIME-

DELAYMUSTBEFIELD

ADJUSTEDTO MEET

LATESTAPPLICABLEANSI/

BHMASTANDARDS.

DMSS

APPROACH

DMSS

SAFETY

ELECTRIC

LOCK

P10

RETROFIT

BODYGUARD

ACTIVATE

DMSS

APPROACH

DMSS

SAFETY

LCN®

XXXXSWING

XXXX-00

SN:XXXX

NoServiceable

Parts Inside

Page4of14 740100-00(5)

2. INSTALLATION

To installthe Middle orSeniorSwingControlBox, follow theAstro/Middle/SeniorSwing installationinstructions

(partNo.740132-00)beginningwith“8.ControlBoxInstallation”onpage12ofthoseinstructions.

CAUTION

Improper installation or set up may result in personal injury or property damage.

Followinstructionscarefully. Foranswerstoquestions,callLCN at: 1-800-526-2400

3. WIRING

• Review the separate wiring diagrams in the accessory instructions so that all wiring can be completed.

• SeeFigure3-1forsystemconfigurationterminology.

• SeeFigure3-2,Figure3-3,and Figure 3-4 for names and locations of control box connectors.

• See Figure 3-5 for control box plug and jack descriptions, wiring, and mating cables.

• SeeFigure 3-6 for electric strike locking device sample wiring.

• SeeFigure3-7forEL(electriclatchretraction) locking device sample wiring.

CAUTION

Whenjoiningorseparatingaplugandreceptacle,donotpushorpullon wires.This

maycause awireto bepulledloosefromaterminal,whichmay resultina malfunction.

Figure 3-1

Connectoperatorforseconddoortocontrol

box Companion Motor Power receptacle

(P5oncontrolboxpower board)

Connect master

operatortocontrol

box Master Motor

Powercable

Connectsingledoor

operator to Master

Motor Power cable

fromcontrolbox

Safety

side

Approach

side

Approach

side

Safety

side

740100-00(5) Page5of14

Figure 3-2. Controlboxpowerboard connectors.

3. WIRING (continued)

Figure 3-3. Controlboxlogicboardconnectors.

Figure 3-4. Closeup ofcontrolboxlogic board connectors.

P3 P2 P1 P6 P7

P4 P10 P8

DMSS (companion; safety side)

Activate

DMSS (master; safety side)

DMSS (master; approach side)

DMSS (companion; approach side)

LOGICBOARD

Companion

motor power

(P5)

POWER

BOARD

LOGICBOARD

AC fuse, 120 VAC

2.5 A time-delay

Master motor

power

Bodyguard (safety side)

Breakaway

3-position

switch

POWERBOARD

LOGICBOARD

See Figure 3-4 for

closeup of control

box logic board

connectors

Locking Interface and

Power Boost disable input

Retrofit

Accessories

Page6of14 740100-00(5)

3. WIRING (continued)

Figure 3-5

Black, 24 VAC

Red, 24 VAC

White, Activate

Green,Ground

Black, 24 VAC

Red, 24 VAC

White,Slowdown

Green,Ground

Black, 24 VAC

Red, 24 VAC

White, Activate

Green,Ground

Black, 24 VAC

White, 24 VAC

Yellow, Activate

Gray, Ground

Black, 24 VAC

White, 24 VAC

Yellow, Activate

Gray, Ground

Blue, Carpet Safety

Gray, Ground

Yellow, Activate

Violet,Slowdown

Orange

Black

Red

Green

Black

Bodyguard

JST-type

connector

ToDMSS

(master;

safety side)

ToDMSS

(master;

approach side)

ToDMSS

(companion;

safety side)

ToDMSS

(companion;

approach side)

To existing cable

710057 (old part

No. 81276)

To 3-position

switch (if used)

To motor cable of

companion operator

(use only for second

door of simultaneous

pair of doors)

To motor cable of

master operator

(always use for

single door)

Bodyguard cable

to Bodyguard

sensor

Cable

761468

Cable

761464

Cable

761464

Cable

761469

Cable

761465 To locking device

(see page 7 for

sample wiring)

Cable

761466

Cable

761463

Retrofit

only

If used

Activate: Initiates a door opening cycle

Bodyguard (master; safety side): Prevents

door from opening; holds open door in open

position (uses door state data from control box

to ignore door movement while opening/closing)

DMSS (master; safety side): Preventsdoorfrom

opening, and slows an opening door

Activate: Initiates a door opening cycle

(operates identically to P6 and is provided as

a convenience if 2 activations are used)

DMSS (master;approachside):Initiatesadoor

opening cycle if activated while door is closing

AC Input: 120 VAC

Companion Motor Power: Companion motor

power (use only for second door of simultaneous

pair or independent pair of doors)

Master Motor Power: Master motor

power (use for single door)

3-Position Switch: OFF, AUTO, HOLD

Locking Interface: Power output and relay

contacts for locking devices; Power Boost

disable input

Breakaway: Disables operator inputs when

Breakaway switch is active

DMSS (companion; safety side): Prevents door

from opening, and slows an opening door

DMSS (companion; approach side): Initiates a

dooropeningcycleifactivatedwhiledoorisclosing

Retrofit Accessories: Accesses older model

Activate, Slow/Stop, and Carpet Safety inputs

P10

LOGIC BOARDPOWER BOARD

To normally closed

Breakaway switch

or jumper 81269

White, 24 VAC

Black, Hot AC

White, Neutral AC

Green,Earth Ground To 120 VAC

Black, 24 VAC

Red, 24 VAC

White,Slowdown

Green,Ground

DMSS

harness

761467

Safety

Approach

Safety

Approach

SafetyApproach SafetyApproach

on-board

connector

on-board

connector

on-board

connector

on-board

connector

on-board

connector

on-board

connector

on-board

connector

on-board

connector

on-board

connector

on-board

connector

permanent

connections permanent

connections

permanent

connections

DMSS

harness

761467

Activate cable

To normallyopenActivatecontacts

Activate cable

To normallyopenActivatecontacts

Usedonly forpowered activationdevice

Blue, Power Boost disable

Black, Ground

Violet, Relay NO

Gray, Relay COM

Brown, Relay NC

Green, 5 V

To normally open

Power Boost

disable contacts

Ground

740100-00(5) Page7of14

The keypad EL (electric lock) setting is SA (fail safe). When the operator is on, the strike is locked when

the door is closed and unlocked when the door is opening. When the 3-position switch is set to OFF, the

strike is unlocked.

The keypad EL (electric lock) setting is SE (fail secure). The control box locking relay signals the PS873

x871-2.Whentheoperatorison,the EL device is locked when the door is closed and unlockedwhenthe

door is opening. When the 3-position switch is set to OFF, the EL device is locked.

Figure 3-7. Sample Wiring for a Fail Secure EL (Electric Latch Retraction) Locking Device

Figure 3-6. Sample Wiring for a Fail Safe Electric Strike Locking Device

Cable761465toMiddleor

Senior Swing control box locking

interfacereceptacle(P10)

Failsafe

electric

strike

Rectifier

(forDC

strikes)

MiddleorSeniorSwing

controlbox

ELdevice

VonDuprin

PS873x871-2

Gray(COM)

Violet(NO)

Cable761465toMiddleor

Senior Swing control box locking

interfacereceptacle(P10) SC I1 O1 GND

MiddleorSeniorSwingcontrolbox

3. WIRING (continued)

NOTE

Alwayswire thelockingdevicetotheNO(normallyopen)contactofthecontrolboxlockinginterface

and use the keypad to set the EL (electric lock) setting to either SA (fail safe) or SE (fail secure).

Control box lock supply rating: 24 VAC, 1.5A

White

Gray(COM)

Violet(NO)

White

Black

Red

Cutconnectoroffrectifier, then

connect using wire nuts

When using an EL device such as EL33A, EL99, etc:

Use 12AWG stranded wire for outputs 01 and 02

betweenPS873andELdevice (200’ run maximum).

Page8of14 740100-00(5)

Figure 4-1. ControlBoxPanelwithKeypad

4. KEYPAD SETTINGS

Settings(exceptforclose speed) for the MiddleandSeniorSwingPowerOperator System are changed using

keypadpushbuttons and an alphanumericdisplayontheAstroSwingcontrol box (Figure 4-1 and Figure 4-2).

Close speed is changed using dials on the control box (Figure 4-1).

Seepage9andpage10fordirectionsforchangingthe values of settings.

Figure 4-2. Closeup of Control Box Keypad

SETTING VALUE

DOWN DOWN

UP UP

DEFAULT

POWER

Setting display

Resettodefault

valuespushbutton

Value selection

pushbuttons

Setting selection

pushbuttons

: OPENINGSPEED

:BACKCHECKSPEED

:BACKCHECKPOS.

: HOLD-OPENDELAY

:LATCHPOSITION

:AUTO-REV.CLOSING

:ELECTRICLOCK

:POWERBOOST

:PUSH‘N’GO

:ALTERNATEACTION

:SAFETYSLOW/STOP

:SLOWDOWNDISABLE

:RESERVED

Value display

CAUTION

Adjust the operator for the slowest operation practical in accordance with the latest

revisionsofAmericanswithDisabilitiesAct,ANSI/BHMA A156.19(AmericanNational

StandardforPowerAssistandLowEnergyPowerOperatedDoors),andlocalcodes.

Keypad

Closespeeddials

CAUTION: 120VAC

2.5ATIME-DELAYFUSE

WARNING: FOR CONTINUED

PROTECTIONAGAINSTFIRE,

REPLACEONLYWITHSAME

TYPEANDRATING OF FUSE.

COMPANION MASTER

SPEED

TCLOSE

SPEED

: OPENINGSPEED

:BACKCHECKSPEED

:BACKCHECKPOS.

: HOLD-OPEN DELAY

:LATCH POSITION

:AUTO-REV. CLOSING

:ELECTRIC LOCK

:POWERBOOST

:PUSH‘N’GO

:ALTERNATEACTION

:SAFETYSLOW/STOP

:SLOWDOWN DISABLE

:RESERVED

SETTING VALUE

DEFAULT

POWER

DOWN

WARNING: ALL SPEED

SETTINGS(OPENING,

CLOSING,ANDLATCHING)

ANDHOLD-OPENTIME-

DELAYMUSTBEFIELD

ADJUSTED TO MEET

LATESTAPPLICABLEANSI/

BHMASTANDARDS.

DMSS

APPROACH

DMSS

SAFETY

ELECTRIC

LOCK

P10

RETROFIT

BODYGUARD

ACTIVATE

DMSS

APPROACH

DMSS

SAFETY

LCN®

COMPANION

MOTOR

XXXXSWING

XXXX-00

SN:XXXX

NoServiceable

Parts Inside

740100-00(5) Page9of14

4. KEYPAD SETTINGS (continued)

WARNING

KEEP HANDS, CLOTHING, WIRES, TOOLS, LADDERS, ETC. AWAY

FROM THE DOOR WHEN THE OPERATOR IS INITIALLY TURNED ON.

SeeFigure4-3 for definitions of the positions of the door throughout theopening and closing cycle.

See Table 4-1 for explanations of the keypad settings.

To change setting values:

1. Set the 3-position switch, if used, to OFF.

2. ApplyAC power. The POWER light will illuminate and the display will remain blank.

3. Press any two pushbuttons at the same time for 1 second to turn on the keypad. The display will illuminate.

4. Press the UP or DOWN setting selection pushbutton to select the desired setting. The setting is

shown in the SETTING display, and the current value for that setting is shown in the VALUE display.

5. Press the UP or DOWN value selection pushbutton to select the desired value for the displayed

setting. The value for the setting is indicated in the VALUE display.

6. The keypad will automatically turn off after 5 minutes of inactivity.

To reset all values to default (default values are listed in Table 4-1 under “Selectable Values”):

1. Set the 3-position switch, if used, to OFF.

2. ApplyAC power. The POWER light will illuminate, and the display will remain blank.

3. Press any two pushbuttons at the same time for 1 second to turn on the keypad. The display will illuminate.

4. PresstheDEFAULTpushbuttonfor4seconds.

5. Thevalues are set to default, and thedisplay will indictatethe opening speedsetting and value.

6. The keypad will automatically turn off after 5 minutes of inactivity.

Back check speed

Back check position

Opening

speed

Closing

speed

Latch position

Deceleration to fully

closed position

Figure 4-3. Door Position Definitions

Page10of14 740100-00(5)

Safety side Door Mounted Safety Sensor (DMSS) disable feature

4. KEYPAD SETTINGS (continued)

Frame

Wall

Active Sensor

(85 degrees or less)

Safety side

DMSS Sensor

Door

DMSS Sensor

Purpose:

Deactivate the Door Mounted Safety Sensor (DMSS) on safety side of door to eliminate

nuisance detection of a wall or guard rail.

1. Install control box, all door hardware and safety devices per their instructions.

2. Setup DMSS sensors in accordance with ANSI standard 156.10.

3. Use keypad to set SAFETY SLOW/STOP (SS) value to STOP (SP).

4. Use keypad to set SLOWDOWN DISABLE (SD) value to 85.

5. Activate door opening cycle. If door does not open fully, use keypad

to reduce SD value from 85 in 5 degree increments.

6. Repeat Step 5 until door opens fully.

7. Perform a complete system test as described in the section 5.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LCN Steuereinheit Handbücher

LCN

LCN ES7902 SEQ Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung