Leadshine M860C Bedienungsanleitung

Read carefully before use & keep for future reference.

V20200069

Laser Autofocus Sensor Kit

Instruction Manual

Parts List

Stepper Driver

Gear Chain Connector Belt Connector

Connecting Cable

Stepper Motor

Autofocus Sensor

Installation Bolts

Safety Information

Warning

• This machine works with lasers which can lead to serious injuries or property damage if used improperly:

• DO NOT operate lasers around combustible or explosive materials.

• DO NOT place bodily parts in the path of the laser.

• ALWAYS wear appropriate personal protective equipment such as protective eyewear when

operating lasers. It is also recommended to secure the worksite or erect protective screens

around the laser path to prevent injury to passersby.

• DO NOT allow children or individuals with impaired physical or mental capacities to operate this machine without strict

supervision and training.

• The working area MUST be equipped with appropriate fire fighting equipment.

• Certain materials can emit gases or radiation when exposed to lasers. It is recommended to research your working

materials before exposing them to the laser so appropriate precautions and equipment can be used.

• DO NOT open the control cabinet or other components while the machine is in use.

• DO NOT leave the machine unattended when it is operational.

• DO NOT operate this machine in overly hot or humid environments.

• DO NOT assemble or disassemble this machine without proper training.

Installation

Operation

1. Install the autofocus sensor on the laser head, making sure the bottom of the sensor is 5–10 mm lower than the

bottom of the laser head.

2. Install and affix the motor in the hole near the Z-axis lifting transmission belt at the bottom of the engraving

machine. If the transmission belt uses a belt, use the belt connector. If the transmission belt uses a chain, use the

gear chain connector.

3. The motor is a two-phase 4-wire motor. Use a multimeter to confirm which wires are A+, A–, B+, and B– although

these are usually color coded red, green, yellow, and blue respectively.

Connect the wiring according to the circuit diagram below.

4. Connect the 4 wires of the motor to the A+, A–, B+, and B– ports of the driver.

5. Connect the power cord of the driver to the 24V DC port of the switching power supply.

6. Connect PUL+/– and DIR+/– of the driver to the corresponding ports of the Z axis on the motherboard.

7. Connect the autofocus sensor to the CN2/CN3 designated position on the motherboard.

8. Confirm that SW1–SW8 of the PA settings on the side of the driver are set to the following positions:

Connect the computer with your copy of RDWorks V8 to the engraving machine. Open the software interface and

enter the factory settings. Adjust the Z-axis and/or U-axis parameters. Set the step length to 0.40000. The home offset

should be the focus height after the autofocus is triggered. You can use the focal length ruler to help determine this

distance and fill in the value.

SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8

OFF ON OFF OFF OFF ON OFF OFF

After the settings are complete, select the autofocus function on the laser engraver control panel menu and test it.

Maintenance

• Periodically clean the field lens of the laser, especially if the engraving quality becomes noticeably poorer.

• Periodically clean the workbench with 75% isopropyl alcohol.

• Remove any dust that accumulates anywhere on the machine before and after each use.

• Periodically confirm that all screws and bolts are fastened properly and tighten any that has become loose.

Thank you for choosing our products! If you have any questions or comments, contact us at [email protected]

and we'll resolve your issue ASAP!

Inhaltsverzeichnis

Andere Leadshine Gleichstromantrieb Handbücher

Leadshine

Leadshine CS3E Series Bedienungsanleitung

Leadshine

Leadshine EM882S Bedienungsanleitung

Leadshine

Leadshine HBS86H Bedienungsanleitung

Leadshine

Leadshine DM2282T Bedienungsanleitung

Leadshine

Leadshine DM860 Bedienungsanleitung

Leadshine

Leadshine EM3E Series Bedienungsanleitung

Leadshine

Leadshine EM556-CAN Bedienungsanleitung

Leadshine

Leadshine DMA882S Bedienungsanleitung

Leadshine

Leadshine DM542E Bedienungsanleitung

Leadshine

Leadshine DM1182 Bedienungsanleitung

Leadshine

Leadshine EM415S Bedienungsanleitung

Leadshine

Leadshine CS-D403 Bedienungsanleitung

Leadshine

Leadshine EM870S Bedienungsanleitung

Leadshine

Leadshine EM3E Series Bedienungsanleitung

Leadshine

Leadshine MX3660 Montageanleitung

Leadshine

Leadshine 3DM883 Bedienungsanleitung

Leadshine

Leadshine DM Series Montageanleitung

Leadshine

Leadshine EM522-CAN Bedienungsanleitung

Leadshine

Leadshine ES2-3DA2306 Bedienungsanleitung

Leadshine

Leadshine CS3E Series Bedienungsanleitung

Leadshine

Leadshine DM542E Bedienungsanleitung

Leadshine

Leadshine CS3E-E Series Bedienungsanleitung

Leadshine

Leadshine DM556E Bedienungsanleitung

Leadshine

Leadshine DM556E Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung