LEAP Electronics WICE-4MA Bedienungsanleitung
EPROM-POD
2
8Bit 16Bit
The standard connecting way of the device 8Bit and 16Bit.
EPROM-POD
WICE-4M-4096
1
AC
Connect the power
supply to the AC
conductor.
Connect to the Printer
Port.
2
WICE
Setup WICE software.
3
1
WICE
Setup WICE hardware and software.
, WICE PORT A / B
According to the following steps, connect PORT A/B
of WICE to the target board that you want to emulate.
4
WICE
Execute WICE software.
5
PORT A / B
Emulate output PORT A/B.
Output signal control.
Quick reference and simple problems solving
WICE-4MA/8MAWICE-4MA/8MA
&WICE-4MA :
The connecting wayof the device 512Kx8Bit ( 27C040).
&WICE-8MA :
1024Kx8Bit ( 27C080)
The connecting wayof the device1024Kx8Bit ( 27C040).
512 Kx8Bit (27C040 )
!WICE-4MA :
The connecting wayof the deviceup to 256Kx8Bit( 27C020 ).
!WICE-8MA :
512Kx8Bit ( 27C040)
The connecting wayof the deviceup to 512Kx8Bit( 27C040 ).
256Kx8Bit ( 27C020)
&WICE-4MA :
The connecting wayof the device256Kx16Bit ( 27C1024-2048).
&WICE-8MA :
512Kx16Bit ( 27C1024-4096)
The connecting wayof the device512Kx16Bit ( 27C1024-4096).
256Kx16Bit ( 27C1024-2048)
'EPROM-POD'
Pin1,Pin31 (7V-12V), Pin
(>7V), 'EPROM-
POD' 10 SMD ,
,
"EPROM-POD" (Protecting Board) : It only can
protect high voltage damage of Pin1 and Pin31 (7V-
12V). If the other pins had irregular high voltage
(>7V), it might cause the "EPROM-POD" 10 SMD
resistor damaged. You can replace it by yourselves
or send itback to usfor service.
LP-32DIP-WICE-3.3V LP-32DIP-WICE-3.3V x 2pcs
4
, , Address BUS ,
'LP-32DIP-WICE-3.3V' ,
If your circuit is faster or it's easily under effects of noise or the Address BUS driver is
not good enough, you can take the special modules"LP-32DIP-WICE-3.3V" to use to
connecting way of the following picture.
EPROM-POD
3
, , ,
, EPROM-POD
If your circuit is faster or it's easily under effects of noise, you can take out the parallel
lines. Use to connecting way of the following picture and connect EPROM-POD into
the target board.
One or two ports output is according
to the volume.
J1 ,
28 32
Attention to the J1 setup. The
choice of 28 or 32 is based on
the devices.pins of the
WICE-4M-4096
LP-32DIP-WICE-3.3V x 2pcs
&WICE-4MA :
The connecting wayof the deviceup to 256Kx8Bit( 27C020/27LV020 ).
&WICE-8MA :
512Kx8Bit ( 27C040/27LV040 )
The connecting wayof the deviceup to 512Kx8Bit( 27C040/27LV040 ).
256Kx8Bit ( 27C020/27LV020 )
&WICE-4MA :
The connecting wayof the device256Kx8Bit ( 27C040/27LV040 ).
&WICE-8MA :
512Kx8Bit ( 27C080/27LV080 )
The connecting wayof the device512Kx8Bit ( 27C080/27LV080 ).
512Kx8Bit ( 27C040/27LV040 )
&WICE-4MA :
1024-2048
The connecting wayof the deviceup to 256Kx16Bit( 27C1024-2048/27LV1024-2048 ).
&WICE-8MA :
512Kx16Bit ( 27C1024-4096/27LV1024-4096 )
The connecting wayof the deviceup to 512Kx16Bit( 27C1024-4096/27LV1024-4096 ).
256Kx16Bit ( 27C1024-2048/27LV )
: 'LP-32DIP-WICE-3.3V'
,
P.S.: "LP32DIP-WICE-3.3V" is an optional
accessory, please call LEAP ELECTRONIC
for details.
Dieses Handbuch passt für folgende Modelle
1
Andere LEAP Electronics Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
