Lefflerpost ATEM2LENS Bedienungsanleitung

ATEM2LENS Users guide Page 1

ATEM2LENS

USERS GUIDE

v2.2

(this users guide is a ‘work in progress’ and will be updated on a regular basis. Please refer to the version number)

***** WARNING *****

Remember to disconnect the 12 volt power when connecting anything to the Fu iCanon

controller. While in most cases it will work there is the possibility it may permanently

disable the controller electronics. There is no problem connecting the extended tally light.

Connections

INTERFACE END

RESET - Resets the controller to startup state

SETUP – Single press enters individual setup modes

ZOOM/IRIS DEMAND - for the Z M/IRIS control

FINE ZOOM NULL – for adjusting any zoom creep

FOCUS DEMAND – for the F CUS control

FOCUS SERVO – for the F CUS SERV UNIT. Note the

range marker to indicate the orientation of the plug.

LENS POWER & IRIS – Connection from the lens

LENS ZOOM – Connection to the lens

INPUT/OUTPUT END

EXTENDED TALLY LIGHT – Allows connection of a tri-

coloured LED to extend PR GRAM/PREVIEW tally.

(this is a 4 pin 3.5mm jack – tip = common,

ring 1 = GREEN, ring 2 = RED, s eeve = BLUE)

RETURN SDI IN – SDI IN from the ATEM

RETURN SDI OUT - SDI UT to the camera

12v POWER IN – Powers the controller and the lens

USB CONFIG/UPDATE PORT – Use this to configure the

lens controller and to provide software updates. It also

is used for status information including Serial Number,

Software Version and override status.

ATEM2LENS Users guide Page 2

Quick Start

There are some things that need to be considered before using any part of the ATEM2LENS controller and

accessories. These include the Fuji anon Basic and Full controller, Thumb zoom demand unit, Joystick demand

unit and the Focus demand unit. These will be discussed briefly here.

Please note that the Fuji anon Basic and Full controllers need to have 12 volts 2 amps supplied to them using

the power in connector. This power is used to feed the controller electronics including powering the lens.

If the 12 volts varies in any way it could affect the lens’s servo system causing slight drifting, especially in the

zoom. When using the Fuji anon Full controller there is a setup procedure discussed later in this document

and the setup also includes a trimpot to null out any residual drift. Once this setup is done it should not need

doing again unless the 12 volt power goes out of adjustment or you change the lens. The usual operation is to

derive the 12 volts either from the same power that is feeding the camera, using the same power source each

time for the controller or always using the controller with a good 12 volt battery. Most camera power supplies

are very good at maintaining very accurate 12 volts but there are many times the camera rig has to run off

batteries.

When using the battery to power both the camera AND the controller everything should run correctly until the

battery starts to go flat. Then you may notice the zoom may start to creep, but by then the camera will

probably shut down.

1. FujiCanon Basic and Full controller

The Fuji anon Basic controller is used for ATEM IRIS only control and the Fuji anon Full controller is

used for ATEM IRIS, ZOOM and FO US with the ability to plug in local FO US, IRIS and ZOOM demand

(control) units.

Both include a Program/Preview tally that is sent to the controller box using the return SDI feed

decoded by the BMD Arduino Shield which is included in the controller package.

The controller unit needs to be set accordingly to what TALLY they will respond to and accordingly

what camera number they will command the lens to.

TOP

FUJI/CANON SETECT – Internally selects Z M control

between a Fujinon lens and a Canon lens. The LEFT

selects a Fujinon lens and the RIGHT selects a Canon

lens.

TALLY/SETUP LED – Displays RED if the selected tally

state is selected on the program buss of the ATEM,

displays GREEN if the selected tally state is selected on

of the ATEM preview buss and displays YELLOW if the

selected tally state is selected on the program buss

AND preview buss of the ATEM. BLUE indicates setup

mode.

ATEM2LENS Users guide Page 3

The SETUP is used in conjunction with the STATUS LIGHT (aka tally). Each setup mode is indicated by

the colour of the Status Light. BLUE indicates CA ERA ALLOCATION mode (tally), AGENTA indicates

STATUS LIGHT BRIGHTNESS, YELLOW indicates FOCUS mode and other colours will indicate future

function setups. Quick presses of the SETUP button steps to the next setup item and LONG pushes will

select the setup item for configuration.

HOW TO SET THE TALLY/CA ERA NU BER

(also see - https://youtu.be/cYx9 1OqzYQ )

a. Using the SETUP BUTTON

There are 2 ways to set the TALLY/ AMERA NUMBER using the SETUP button. The first is by

pressing the SETUP button the number required (GREEN MODE) and the second is by selecting the

number required on the PREVIEW ROW of the ATEM (RED MODE).

GREEN ODE

i. SHORT press the setup button. The STATUS LED turns BLUE

ii. LONG press and HOLD the SETUP button until the STATUS LED turns GREEN

iii. SHORT press once for input 1, twice for input 2 etc (max of 20)

iv. When the required number is reached PRESS and HOLD until the LED turns WHITE

v. Release the button and the STATUS LED will turn AGENTA (meaning it has set the

TALLY/ AMERA NUMBER from the button count and moved on to the next setup mode.

vi. SHORT press the setup button to bypass each other setup mode until the LED indicates leaving

setup by flashing RED, GREEN, BLUE 3 times.

RED ODE

i. SHORT press the setup button. The STATUS LED turns BLUE

ii. Select the camera number you want to allocate on the PREVIEW ROW of the ATE

iii. LONG press the SETUP button until the STATUS LED turns RED

iv. Release the SETUP button and the STATUS LED will turn AGENTA (meaning it has completed

the allocation from the PREVIEW ROW and moved on to the next setup mode.

v. SHORT press the setup button to bypass each other setup mode until the LED indicates leaving

setup by flashing RED, GREEN, BLUE 3 times.

vi. When the setup mode has finished the STATUS LED will display GREEN as it now detects it is

selected on the PREVIEW ROW. If it is also selected on the PROGRAM row it will display

YELLOW.

b. Using the TER INAL USB port

i. Type t1[ENTER] to set the camera allocation to input 1

ii. Type t2[ENTER] to set the camera allocation to input 2

iii. Type t14[ENTER] to set the camera allocation to input 14 etc

HOW TO VIEW THE TALLY/CA ERA NU BER

a. LONG press the setup button. The STATUS LED turns WHITE for about a second and then blinks RED

for the camera number allocated.

b. After it has counted the camera number it will turn WHITE for about a second and exit the setup

mode.

ATEM2LENS Users guide Page 4

HOW TO SET THE TALLY/CA ERA LED BRIGHTNESS

(also see - https://youtu.be/cYx9 1OqzYQ )

a. Using the SETUP BUTTON

i. Short press the SETUP button on and off until the STATUS LED turns AGENTA.

ii. Press and HOLD the SETUP button. The STATUS LED will slowly increase in brightness until it

reaches maximum. It will then step back to the minimum and start increasing in brightness

again.

iii. Release the SETUP button when the desired brightness is achieved.

iv. SHORT press the setup button to bypass each other setup mode until the LED indicates leaving

setup by flashing RED, GREEN, BLUE 3 times.

b. Using the TER INAL USB port

i. Type b[ENTER] to start the STATUS LED slowly increase in brightness until it reaches

maximum. It will then step back to the minimum and start increasing in brightness again.

ii. Type [ENTER] when the desired brightness is achieved.

HOW TO VIEW THE AUTO ATICALLY SET THE ZOO CREEP

a. Using the SETUP BUTTON

Short press the SETUP button on and off until the STATUS LED turns CYAN.

Long press the setup button and the LED will turn RED. The Lens will zoom in full and then slowly

zoom out while fast flashing between GREEN and AGENTA as it searches for the zoom NULL.

The adjust mode will exit once it sees no movement for 10 seconds or pressing the set up button.

b. Using the TER INAL USB port

Type z[ENTER]. The Lens will zoom in fully and then slowly zoom out (move lens manually if it

does not start zooming). The screen will display 'adjusting' including the current zoom position

and null value. While it automatically adjusts the zoom speed it looks for non movement. This will

be the non crawl value. The adjust mode will exit once it sees NO movement for 10 seconds or

pressing any key.

You may need to manually adjust the TRIMPOT to null out residual zoom creep.

HOW TO TOGGLE THE FOCUS DIRECTION (only for Focus Controller usage)

a. Using the SETUP BUTTON

i. Short press the SETUP button on and off until the STATUS LED turns YELLOW.

ii. Long press the SETUP button.

iii. The FO US has now reversed its direction.

b. Using the TER INAL USB port

i. Type f[ENTER].

ii. The FO US has now reversed its direction.

ATEM2LENS Users guide Page 5

HOW TO NULL THE ZOO CREEP USING THE FOCUS KNOB

a. Using the SETUP BUTTON

i. SHORT press the setup button. The STATUS LED turns BLUE

ii. PRESS and HOLD IN the FO US KNOB

iii. ROTATE the FO US KNOB until the creeping stops

(You may need to use the lens zoom rocker to zoom back if the creeping has gone to either

zoom end)

iv. SHORT press the setup button to bypass each other setup mode until the LED indicates leaving

setup by flashing RED, GREEN, BLUE 3 times.

v. Manually adjust the TRIMPOT to null out residual zoom creep

Note: While watching slow movement in one direction, when it stops moving your eyes start

perceiving that the movement has falsely started in the opposite direction. Do not be deceived by this.

I recommend using the actual picture from the camera the lens is attached to, to detect any residual

zoom creep.

ATEM2LENS Users guide Page 6

Installing the Drivers

Windows –

1. go to http://www.lefflerpost.com.au/LENS ONTROL/utilities/ and download the drivers folder

2. Plug the ATEM2LENS controller into the P using the supplied USB cable

This will power the unit and provide a communications link to the P

3. lick on the Start Menu and open up the ontrol Panel

4. Open the Device Manager

5. Go to ‘Other devices'

Look for ‘USB-SERIAL H340’ or ‘Arduino Uno’

If it does not appear in ‘other devices’ then go to ‘Ports ( OM & LPT)’

If it listed here it will already have a driver installed and a com port allocated

6. Right click on the ‘USB-SERIAL H340’ or ‘Arduino Uno’ and choose "Update Driver Software"

7. Select the "Browse my computer for Driver software”

8. Navigate to (Browse...) and select the ‘driver’ folder that you downloaded in step 1

9. press OK

10. press ‘Next’

11. If the 'Windows Security' warning appears select 'Install this driver software anyway'

12. The driver will install and then display Success

13. Press lose

In the Device manager the ATEM2LENS controller will show up in ‘Ports ( OM & LPT)’ as “USB-SERIAL H340

( OM[port])” or “Arduino Uno ( OM[port])”. The P automatically allocates the port number.

Every time you connect this ATEM2LENS controller to your P the com port allocated will be remembered.

ac –

No drivers are needed to be loaded for MA OSX. To confirm the ATEM2LENS controller is recognized

by the MA –

1. Select ‘System Preferences’

2. Select ‘Network’

3. The ‘USB-SERIAL H340’ or ‘Arduino Uno’ has been identified as a ‘Modem’

ATEM2LENS Users guide Page 7

Setting up the Terminal

Windows –

The recommended P terminal program is called ‘PuTTy’ and it is freeware .

1. go to http://www.lefflerpost.com.au/LENS ONTROL/utilities/ and download Putty.exe

This is a non intrusive stand alone program (does not do any registry modifications)

2. Run ‘PuTTY.exe’ by double clicking on it

3. After ‘PuTTY’ starts select ‘serial’

4. Enter the required ‘serial port’ (as seen above when installing the driver)

5. Enter the speed of 115200

6. Enter the name you wish to call the connection

7. Press ‘Save’

8. Press ‘Open’

9. This will open the terminal window and restart the ATEM2LENS controller

ac –

The recommended MA terminal program is called ‘terminal’ and it is part of the OS .

Please follow the instructions on this link-

http://www.dummies.com/computers/arduino/how-to-install-arduino-for-mac-os-x/

Inhaltsverzeichnis

Andere Lefflerpost Controller Handbücher

Lefflerpost

Lefflerpost RMC2ATEM Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung