Legacy Mist Bedienungsanleitung
2
Registration
3. Owners Record
4. The Cabinetry / Our Commitment
Setup
5. Unpacking Your Speakers
6. Speaker Placement / Installation
8. Hook up Cables
10. Amplification
13. Speaker Connections
Technology
14. Designer’s Note
16. Specifications
3
The model and serial numbers are located on the rear of the unit. Record
these numbers in the spaces provided below. Refer to them when calling
upon your dealer regarding this product.
Model No. _______________________________
Serial No. _______________________________
Date of purchase: _________________________
Thank you for selecting a Legacy Loudspeaker System. These hand-
crafted instruments will provide you with many years of listening
enjoyment. Please take a few moments to read this brief manual to insure
maximum benefit from your speaker system.
4
Handcrafted
Beneath the surface of MiST’s elegant exterior lies rigid MDF construction.
Interlocking joinery maximizes the strength of the cabinet parts. Polyester
fiberfill is selected for internal damping. A sharp rap on the enclosure will
leave you with little more than bruised knuckles.
Each cabinet is impeccably finished on all exposed surfaces with select
veneers. The exquisite finish is hand-rubbed several times to assure a
patina at home with the most elegant decor.
Our Commitment
A great deal of forethought, love and satisfaction is instilled in each piece
of Legacy workmanship. We take pride in getting to know many of our
customers on a first name basis.
Your purchase of this product is backed by the renowned “Legacy
Satisfaction Guarantee”.
5
Your new speaker system has been very carefully packaged to insure that
it travels to you safely. Each speaker is protected by a heavy outer carton
with V-board corner protectors. Molded foam end caps are used to protect
the elegant cabinetry, and a plastic liner is provided as waterproofing.
Please save this packing for future transportation. If cartons become
damaged or misplaced, new ones can be purchased from Legacy Audio.
6
A pair of MiST should be wall mounted approximately 6’ high and to the
sides of the listener. An optional third MiST may be used as a center rear
channel by mounting the unit behind the listener. Because MiST is actually
two independent, opposite facing, side-firing arrays in one cabinet, it
behaves as a bipolar system. When used behind the listener it may be
powered by both the left and right rear channel inputs.
Though the MiST requires only one channel of amplification per unit to
drive it when configured in the standard mode, separate input terminals for
each array allow for future steering versatility.
Instructions for attaching bracket to wall
1. Selecting a mounting site.
Note: Try to find a site with a solid wood backing.
2. Using one of the brackets as a pattern, mark four holes on the wall,
aligning the vertical holes with a stud location.
3. Drill four 1/8” (.32 cm) diameter holes as marked.
4. Fasten one bracket to the wall with four wood screws provided. (See
Figure 1)
7
5. Hang the speaker.
WARNING: Woodscrews provided may pull out of sheetrock or wall
paneling without a wood brace. They might also pull out of thin speaker
panels or perforated particle board. See Figure 2 & Figure 3 for alternate
mounting hardware.
8
The ideal conductor would have negligible resistance, inductance and
capacitance. The table below shows how a few actual speaker cables
measure up.
Cable Ωs/ft pF/ft µH/ft
12 ga. 0.0033 24 0.21
14 ga. 0.0048 17 0.13
16 ga. 0.0079 16 0.18
18 ga. 0.0128 28 0.21
Capacitance is considered insignificant in each cable because its effect is
well out of the audio bandwidth; inductance can be decreased (at the
expense of increased capacitance) by keeping the conductor pair closely
spaced.
How long would a cable have to be before inductance effects would
impinge on the audio spectrum? Approximately 300 feet of 12 gauge
would be required to establish a corner frequency of 20 kHz with an 8
Ohm loudspeaker. As you see, inductance is not a problem for most of us.
9
What about phase shift due to frequency dependent travel times down the
speaker cable? Measurements show that 100 Hz waves will be delayed
about 20 billionths of a second behind 10 kHz waves when traveling to the
end of a 10 foot speaker cable. Since the cilia of the ear requires 25,000
times longer than this just to transmit phase information, phase shifting is
obviously not the primary concern when considering speaker cables.
What about resistance? Finally we are getting somewhere.
Resistance is the controlling factor of the amplifier/loudspeaker interface.
Excessive resistance can cause major shifts of speaker crossover
frequencies. The lower the impedance of the loudspeaker, the greater the
effects of series resistance. A 20 foot run of 18 gauge cable can cause up
to 10% deviations of crossover center frequencies. That same 20 feet can
un-damp your damping factor and reduce your systems’ output by one-
half decibel.
In summary, there are no perfect cables. The best way to approximate the
ideal would be to keep loudspeaker leads as short as is practical.
10
Ideally the loudspeaker would be among the first components selected
when assembling a playback system. This would allow the user to choose
an amplifier capable of delivering adequate amounts of current into the
frequency dependent load presented by the loudspeaker. However, when
upgrading a system, audiophiles may find themselves matching their new
loudspeakers to their existing amplification. For this reason, extensive
measures have been taken to ensure that each Legacy speaker system
represents a smooth, non-reactive load to virtually any amplifier.
Often there is much confusion regarding amplification and loudness levels.
It should be understood that the role of the amplifier goes beyond that of
driving loudspeakers to a given sound pressure level. The amplifier should
be able to CONTROL the loudspeakers across the entire music spectrum.
This means that parameters such as damping factor (values greater than
60 are acceptable) and dynamic headroom should not be overlooked
when comparing amplifiers.
Andere Legacy Lautsprechersystem Handbücher
Legacy
Legacy Signature SE Bedienungsanleitung
Legacy
Legacy AERIS Bedienungsanleitung
Legacy
Legacy Deco Bedienungsanleitung
Legacy
Legacy Whisper XD Bedienungsanleitung
Legacy
Legacy Focus Bedienungsanleitung
Legacy
Legacy Silhouette Bedienungsanleitung
Legacy
Legacy Studio HD Bedienungsanleitung
Legacy
Legacy Focus HD Bedienungsanleitung
Legacy
Legacy Helix Bedienungsanleitung
Legacy
Legacy Expression Bedienungsanleitung
Legacy
Legacy Whisper HD Bedienungsanleitung
Legacy
Legacy Victoria LE Bedienungsanleitung
Legacy
Legacy FOCUS SE Bedienungsanleitung
Legacy
Legacy FOCUS XD Bedienungsanleitung
Legacy
Legacy Sconce Bedienungsanleitung
Legacy
Legacy Harmony Center Bedienungsanleitung
Legacy
Legacy Signature III Bedienungsanleitung
Legacy
Legacy Focus HD Bedienungsanleitung
Legacy
Legacy Classic HD Bedienungsanleitung
Legacy
Legacy FOCUS SE Bedienungsanleitung
Beliebte Lautsprechersystem Handbücher anderer Marken
Sondpex
Sondpex Active Speaker System and Digital Music... Bedienungsanleitung
JVC
JVC NX-PN7 Bedienungsanleitung
Marshall Amplification
Marshall Amplification AR-DM61-BT Bedienungsanleitung
Yamaha
Yamaha NX-A01 - Speaker Sys Bedienungsanleitung
SE Audiotechnik
SE Audiotechnik I-LINE Bedienungsanleitung
Gemini
Gemini WRX-843 Series Bedienungsanleitung