LEGRAND 4 149 29 Bedienungsanleitung

1 / 14

LEGRAND - BP30076

87045 LIMOGES CEDEX FRANCE

Telephone: +33 5 55 06 87 87 –Fax: +33 5 55 06 88 88

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

Contents Pages

1. Description - Use ............................................. 1

2. Range............................................................... 1

3. Overall dimensions .......................................... 1

4. Preparation - Connection................................. 1

5. General characteristics .................................... 4

6. System architectures ....................................... 8

6.1 Stand-alone........................................................ 8

6.1.1 with local addressing ..................................... 8

6.1.2 with remote addressing ................................. 8

6.2 Supervised ....................................................... 10

6.2.1 with local addressing ................................... 10

6.2.2 with remote addressing ............................... 12

7. Compliance and approvals ............................ 14

1. DESCRIPTION - USE

. Module dedicated to Energy Management System (EMS CX3) use.

. Auxiliary and Fault signalling electronic module (CA+SD): indicates

contacts position (open or closed) and fault tripping of Legrand

modular associated device (MCB, RCBO, RCCB or Remote trip

head IS).

Symbol:

2. RANGE

. Cat. n° 4 149 29: electronic auxiliary contact (CA) + fault signalling

(SD).

Width:

. ½ module. 8,8 mm width.

3. OVERALL DIMENSIONS

4. PREPARATION -CONNECTION

Fixing:

. On symmetric rail EN/IEC 60715 or DIN 35 rail

Operating positions:

. Vertical, Horizontal, Upside down, On the side

Power Supply:

. Mandatory in 12 VDC via the specific Power supply module Cat n°4

149 45

. Two ways:

via specific communication patch cords (cat. nos 4 149 07/08/09) to

connect at the downstream through dedicated ports

via specific communication rails (cat. nos 4 149 01/02/03) to

connect at the rear through dedicated connectors.

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

2 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

4. PREPARATION –CONNECTION

(continued)

Manual action of the CA + SD:

. By the handle of the associated device.

Assembling:

. On the left side of Legrand MCB, IS, RCBO or RCCB

. No tools are required. Clipped by mean of plastic clamps on the

associated device.

. Assembling products in OFF position

. The switching device of signalling auxiliaries must fit into the

housing of the handle of the associated device.

List of allowed associations (General rules):

Three auxiliaries maximum which:

- two signalling auxiliaries

(Cat. nos 4 062 50/52/56/58/60/62/64/66, 4 149 29).

- only one control auxiliary

(Cat. nos 4 062 76/78/80/82/84/86/87).

. If signalling and control auxiliaries are associated on the same

circuit breaker, the control auxiliary must be placed to the left of the

signal auxiliary (ref. 4 062 5x / 6x or 4 149 29).

List of allowed associations (Particular rules):

. With MCB’s 1,5 modules per pole width:

- if a remote tripping auxiliary (Cat. nos 4 062 76/78/80/82/84/86/

87) is already mounted on this kind of device, only 1 module

width signalling auxiliaries (Cat. nos. 4 062 64/66) can be added.

In this set up the ½ module signalling auxiliaries will not operate.

Nothing changes for the other modular references.

. With an isolating switch DX3-IS:

- only one signalling auxiliary CA type (Cat. nos 4 062

50/56/58/62/64/66) or CA+SD (Cat. n° 4 149 29).

. With a remote trip head isolating switch DX3-IS, three auxiliaries

maximum which:

- one or two signalling auxiliaries CA type Cat. nos 4 062

50/56/58/62/64/66) or CA+SD (Cat. n° 4 149 29).

- one control auxiliary (Cat nos 4 062 4 062 76/78/80/82/84/86/

87).

4. PREPARATION –CONNECTION

(continued)

Combination tables of the auxiliaries:

. For devices 1 module per pole width:

. For devices 1,5 modules per pole width:

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

3 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

4. PREPARATION –CONNECTION

(continued)

Data connection (EMS CX3modules inter-connection):

. Via specific communication patch cords (cat. nos 4 149 07/08/09)

Allow data transmission between the different EMS CX3modules.

This type of connection is recommended when there are few EMS

CX3modules, distributed all over the enclosure.

Implementing: with this configuration, the plastic protection cover of

the backside communication ports on the EMS CX3module must be

keep on.

4. PREPARATION –CONNECTION

(continued)

Data connection (EMS CX3modules inter-connection)

(continued)

. Via specific communication rails (cat. nos 4 149 01/02/03).

. Allow data transmission between the different EMS CX3modules.

This type of connection is recommended when there are several

EMS CX3modules on the same DIN row.

Implementing: with this configuration, the plastic protection cover of

the backside communication ports on the EMS CX3module must be

removed.

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

4 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

4. PREPARATION –CONNECTION

(continued)

Data connection (EMS CX3modules inter-connection)

(continued)

. Via a mix between specific communication patch cords and

communication rails in order to create a link between several rows

Two situations:

-Individually connected with communication rails.

The communication patch cord allows to connect two rows.

-Individually connected with communication patch cords &

communication rail.

The communication patch cords allow to connect EMS CX3

module on a row and to connect two rows.

5. GENERAL CHARACTERISTICS

Front face marking:

. By permanent ink pad printing (red line) and laser marking

Lateral side marking:

. By laser.

left side: Standard and programming information

right side: installing and traceability information

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

Function name:

CA = auxiliary contact

SD = fault signalling

Legrand address

Indicates the presence

of the addressing

track-wheel

Assembling

information

Traceability

information

Data connection

with communication

rail

Data connection

with communication

patch cords

Standards

Label: to be removed

and kept if necessary

(ID and module info…

5 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

5. GENERAL CHARACTERISTICS

(continued)

Test button:

. It allows to check the correct association between the module and the associated device.

Functions button:

. Front face button as several functions:

. Give information about the operating state on the module

Possible states:

Led colour

State

Meaning

red

Slow blinking

Error (e.g. addressing error)

Fast blinking

No function

Steady

(pressing the

multifunction button

longer than 20 sec.)

Total reset

[any firmware updates are

preserved]

green

Slow blinking

System process is running.

Wait until the Led turns steady

Fast blinking

(pressing the

multifunction button

for 10 sec.)

put in “Stand-by” the EMS CX3

module (no remote action and

communication available)

Steady

System OK, connection is

running

orange

Slow blinking

Creation of a link with “Link

Functionality” procedure

(see

next §)

Fast blinking

Device’s firmware update in

progress

Steady

No function

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

6 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

5. GENERAL CHARACTERISTICS

(continued)

Link Functionality:

. This function allows you to link two EMS CX3modules to create automatic actions that, once programmed, can run independently without a

connection to a manager is needed.

The basic rule is the link between an event (circuit breaker that trip, a threshold exceeded, etc.) and an action accordingly (signalling, opening

of a circuit by motorized control or contactor, etc.).

Possible associations are:

Action module

Event

generator

Command:

4 149 32

State +

Command:

4 149 31

State:

4 149 30

Measure:

4 149 19/20/23



Only with the module configured

(locally or remotely) as shown:

State:

4 149 29/30





Is sufficient to configure the

module (locally or remotely) as

˝Slave˝

State + Command:

4 149 31





Is sufficient to configure the

module (locally or remotely) as

˝Slave˝

Note:

- association can only be of type 1 to 1 (1 event and 1 action).

- modules already associated cannot be used for other associations.

- all the configuring procedure will be done with the Configuration Software (available online for free).

[For more details refer to the Installation Manual

of EMS CX3Configuration software]

Modules compatible with “Link Functionality” feature: firmware versions and production date:

Cat n°

Firmware version

Production date indicated on the label

sticked on the side of the module

4 149 19

ver. ≥ 2.0.1

date ≥ 18W29

4 149 20

ver. ≥ 2.0.1

date ≥ 18W49

4 149 23

ver. ≥ 2.0.1

date ≥ 18W49

4 149 29

ver. ≥ 2.0.1

date ≥ 18W49

4 149 30

ver. ≥ 2.0.2

date ≥ 18W32

4 149 31

ver. ≥ 2.0.6

date ≥ 18W45

4 149 32

ver. ≥ 3.0.2

date ≥ 18W39

4 149 36

ver. ≥ 2.0.4

date ≥ 18W38

4 149 37

ver. ≥ 2.0.4

date ≥ 18W43

4 149 40

ver. ≥ 3.0.8

date ≥ 18W34

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

7 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

5. GENERAL CHARACTERISTICS

(continued)

Insulation voltage:

. Ui = 400 V

Pollution degree:

. 2 according to IEC/EN 60898-1.

Overvoltage category:

. III

Dielectric strength:

. 2500 V

Tripping force:

. Between 1 and 1,5 Nm.

Mechanical endurance:

. These devices support the mechanical cycles of the associated

devices

. 20,000 manoeuvres

Plastic material:

. Self-extinguishing polycarbonate.

. Heat and fire resistant according to IEC/EN 60695-2-12, glow-wire

test at 960°C.

. Classification UL 94 / IECEN 60695-11-10: V1

Ambient operating temperature:

. Min. = -25°C. Max. = +70°C

Ambient storage temperature:

. Min. = -40°C. Max. = +70°C

Protection Index:

. Protection index of terminals against direct contacts:

IP2X (IEC/EN 60529).

. Protection index of terminals against solid and liquid bodies (wired

device): IP 20 (IEC/EN 60529).

. Protection index of the front face against solid and liquid bodies: IP

40 (IEC/EN 60529).

. Class II, front panel with faceplate.

Average weight per device:

. 0,032 kg.

Volume when packed:

. 0,21 dm3.

Consumption:

. Values at 12 VDC

0,236 W

19,7 mA

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

8 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

6. SYSTEM ARCHITECTURES

The EMS CX3is a polyvalent system and, according to the needs of the customer, can be set up and/or used as “Stand-alone” or “Supervised”

system. Based on this choice the configuration and addressing methods are different.

Four possible architectures are provided:

6.1 Stand-alone system

6.1.1 with local addressing (through the track wheel)

6.1.2 with remote addressing (through a computer)

6.2 Supervised (Computer Supervisory System)

6.2.1 with local addressing

6.2.2 with remote addressing

6.1 Stand-alone system

. Stand-alone = autonomous system. To be used by the end-user if it is not necessary to have a computer for the supervision outside the

envelope. Everything can be managed on site.

6.1.1 Stand-alone system with local addressing (through the track wheel)

Local addressing advantages:

-No configuration software needed to set-up the installation

-It is not necessary to use a computer to manage settings (configurations, test, ...) and to use the system (visualize and be alerted,

...). Everything can be done through the Mini configuration module (local display, cat. no 4 149 36/37).

[Refer to the technical sheet

dedicated to this module for details]

-No communication Interfaces or gateways are required.

-Installation can be done without the intervention of a System Integrator

Programming procedure:

. For EMS CX3modules which need some: mandatory through to lateral DIP-switch of each EMS CX3 modules (see § ”Module configuration”)

Addressing procedure:

. For all EMS CX3modules: mandatory through the track wheel located on the top upper face of each EMS CX3 modules

. Marked from 0 to 9 in order to locally define the Modbus address of the EMS CX3 modules

Consequences of the local addressing mode (through the track wheel):

. Each device of the system must be addressed.

. Addresses available: from 1 to 9

. Address 0 not permitted

. It is possible to assign to several devices the same address with the purpose of grouping different functions, because they are related to the

same electrical circuit. For example, it is possible to assign the same address to a signalling auxiliary module (cat. no 4 149 29), a universal

control module (cat. no 4 149 32), a measuring module, and so on. In this way on the EMS CX3mini configuration module (local display) the

grouped function will be displayed as a unique “device” with all grouped functions.

[Refer to the schemes hereunder]

Note for the mini configuration module (local display)

. It is possible to assign it the same address as another EMS CX3through the programming menu of the device

. The mini configuration module can be placed everywhere in the EMS CX3bus

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

9 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

6. SYSTEM ARCHITECTURES

6.1 Stand-alone system

(continued)

6.1.2 Stand-alone system with remote addressing (through a computer)

Remote addressing advantages:

-Whole configuration (addresses and functions) can be set up through the EMS Configuration software

-Configuration software available for free

-Automatic detection of the EMS CX3modules installed in the system (characteristics, functions, configuration...)

-Increased settings possibilities: load shedding function

-Increased addressing: up to 30 Modbus addresses in a system

Programming procedure:

. For EMS CX3modules which need some: possible through the lateral DIP-switch of each EMS CX3 modules (see § “Module configuration”).

Addressing procedure:

. It is not necessary to address the EMS CX3modules. The track wheel must be left in default position “0”.

. All the addressing/configuring procedure will be done with the Configuration Software (available online for free)

. With remote addressing, the software does the automatic detection of modules installed in the system, but the supervision is not possible until

the user assigns the remote address and all the characteristics to each module.

Note: it is mandatory to connect the computer to the mini configuration module with an USB-micro USB cable.

[For more details, refer to User

Manual Document]

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

10 / 14

EMS CX3- Signalling Auxiliary Contact

(CA + SD)

Cat. N°: 4 149 29

6. SYSTEM ARCHITECTURES

6.1 Stand-alone system

(continued)

6.1.2 Stand-alone system with remote addressing (through a computer)

(continued)

Consequences for the system architecture:

-for 1 mini configuration module (cat. no 4 149 36/37)

oup to 30 EMS CX3modules (eg. 30 devices grouped per functions with addresses from1 to 30)

It is possible to assign to several devices the same address with the purpose of grouping different functions, because they are related to the

same electrical circuit. For example, it is possible to assign the same address to a signalling auxiliary module (cat. no 4 149 29), a universal

control module (cat. no 4 149 32), a measuring module, and so on. In this way on the EMS CX3display or in a supervision system the grouped

function will be displayed as a unique “device” with all grouped functions.

[Refer to the schemes here under]

Note for the mini configuration module (local display)

. It is possible to assign it the same address as another EMS CX3

. The mini configuration module can be placed everywhere in the EMS CX3bus

6.2 Supervised system (Computer Supervisory System)

. Supervised system = System to be used through a Computer Supervisory System to remotely read data from the EMS CX3devices and/or do

operations on these devices (e.g. commands of a motor driven or contactor ...).

6.2.1 Supervised system with local addressing (through the track wheel)

Local addressing advantages:

-No configuration software needed to set-up the installation

-Installation can be done without the intervention of a System Integrator

Programming procedure:

. For EMS CX3modules which need some: mandatory through to lateral DIP-switch of each EMS CX3 modules (see § “Module configuration”)

Addressing procedure:

. For all EMS CX3modules: mandatory through the track wheel located on the top upper face of each EMS CX3 modules

. Marked from 0 to 9 in order to locally define the Modbus address to EMS CX3 modules

In this system the Modbus address of an EMS CX3module device or group of modules (several functions) is obtained considering the address

of the interface Modbus/EMS CX3Interface as tenth and the address of a device or group of function as unit (e.g. Interface address 1 = 10 

address of module n°5 = Modbus address 15)

Technical data sheet: F02334EN/02

Updated: 07/11/2018

Created: 20/07/2016

Inhaltsverzeichnis

Andere LEGRAND Steuereinheit Handbücher

LEGRAND

LEGRAND DRD5 v2 Bedienungsanleitung

LEGRAND

LEGRAND adorne Night Light Bedienungsanleitung

LEGRAND

LEGRAND LCS 0 321 28 Bedienungsanleitung

LEGRAND

LEGRAND 0 648 85L Bedienungsanleitung

LEGRAND

LEGRAND 882 15 Bedienungsanleitung

LEGRAND

LEGRAND EMDX3 MI Bedienungsanleitung

LEGRAND

LEGRAND 6338 53 Bedienungsanleitung

LEGRAND

LEGRAND 739 60 Bedienungsanleitung

LEGRAND

LEGRAND 067697 Anleitung zur Verwendung

LEGRAND

LEGRAND 416 50 Bedienungsanleitung

LEGRAND

LEGRAND 4 131 01 Bedienungsanleitung

LEGRAND

LEGRAND 4 121 73 Bedienungsanleitung

LEGRAND

LEGRAND Galion TV - R- SAT Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMIN-104 Bedienungsanleitung

LEGRAND

LEGRAND Mosaic VDI 0 332 80 Bedienungsanleitung

LEGRAND

LEGRAND 882 05 Bedienungsanleitung

LEGRAND

LEGRAND 4 149 40 Bedienungsanleitung

LEGRAND

LEGRAND 0 677 55L Bedienungsanleitung

LEGRAND

LEGRAND VM1000 Bedienungsanleitung

LEGRAND

LEGRAND 0 677 23L Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper IPPAN3-B Bedienungsanleitung

LEGRAND

LEGRAND 882 04 Bedienungsanleitung

LEGRAND

LEGRAND 675 07 Bedienungsanleitung

LEGRAND

LEGRAND 674 56 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung