LEGRAND ADMHRM4 Bedienungsanleitung

ADMHRM4

Wireless Room Scene Remote

Specifications

Power Supply ................Two AAA Alkaline Batteries, provided

Operating Temperature.................32°F to 104°F (0°C to 40°C)

Installation Instructions

UNIT DESCRIPTION

The adorne ADMHRM4 Wireless Room Scene Remote is a room level scene

controller. It provides instant recall of four user-recorded lighting scenes (or

presets) assigned to a room or designated area. It also provides off and on

functions, overall control of the room’s light level, all with convenient, handheld

portability.

It is used to control a variety of adorne wireless devices including dimmers,

switches, plug-in appliance modules and plug-in lamp modules.

The ADMHRM4 is a battery operated portable device, so you can use it to control

its designated room from anywhere in the house. Each ADMHRM4 is assigned

to one room and cannot operate devices that are bound to different rooms (see

(ROOM BINDING).

You can control up to 4 scenes in the room with a ADMHRM4 (see MORE SCENES

section). You can use additional room scene remotes to control those scenes

from multiple locations.

adorne Wireless

adorne wireless devices use radio signals to communicate with each other to

control lighting and other types of electric loads in selected areas. They use the

900MHz band for high-speed control communication. Using the Watt Stopper’s

own “frequency-agile” Top Dog™ technology, adorne wireless devices avoid

interference with other 900MHz devices, such as cordless phones and baby

monitors.

Application Assistance

The adorne Installation Guide provides more information about conﬁguring

scenes. Instructions for installation and use are included with the relevant

adorne wireless devices. Application support information and the adorne

Installation Guide is available online.

SET HOUSE ID

All adorne wireless devices installed in the same home must acquire the same

unique House ID before use. This process is known as house binding. Each

adorne wireless device is bound to all other adorne wireless devices in the

house.

New Installation

1. With all devices installed and

energized, make sure that every

adorne wireless device LED is

orange. If any LED is off, be sure

the circuit breaker is on and the

device is correctly installed. The

ADMHRM4 remote shuts down

when it is not in use. Press any

button to activate the remote and illuminate its LED.

2. Press on any device paddle until the LED ﬂashes orange (about 5 seconds ).

This indicates that it has acquired a unique House ID.

3. Make sure that all other adorne wireless device LEDs are ﬂashing green,

indicating that they have acquired the same House ID. For ADMHRM4

remotes, be sure that the units are awake during the binding process. Press

any button to activate the remote and illuminate its LED.

4. Return to the device used in step 2, which is still ﬂashing orange. Press

until the LED changes to solid white (about 5 seconds ). All device LEDs in the

House change to solid white, indicating house binding is complete.

Adding an ADMHRM4 to an Existing Installation

If you’re adding or replacing a device in a adorne wireless installation that is

already operating, the new device must be bound to the same House ID as the

other adorne wireless devices in the house. After the new ADMHRM4 is powered

up, the LED should be solid orange. This indicates that it has not yet acquired a

House ID. To acquire the House ID for the existing system:

1. Press on any previously bound device until the LED ﬂashes orange (about 5

seconds ).

2. Be sure that the ADMHRM4 is awake during the binding process. Press any

button to activate the remote and illuminate its LED. Verify that the new

ADMHRM4 LED is ﬂashing green, indicating that it has acquired the House ID.

3. Return to the same previously bound device used in step 1 and press until

the LED changes to solid white (about 5 seconds ). All device LEDs should

now be solid white.

When you see

in the instructions,

ﬁrmly press and

hold both the top

and bottom of

the paddle until

the LED changes

(about 5 seconds ).

ROOM BINDING

After the House ID is set in the remote, you create a room by binding devices

to the remote. You can also add the ADMHRM4 to an existing room. When a

new ADMHRM4 is added to a room, its scene buttons execute the same scenes

as other room scene controllers with the same scene set assignment (see

MORE SCENES). Paddle functions are the same at every room scene remote and

controller that is bound to the same room, regardless of scene set assignment.

IMPORTANT: If you are planning to use Groups in the room, you should bind

those devices together before beginning the room binding process. Group binding

instructions are provided with individual devices.

Binding a New Room

1. With all devices installed and energized, make sure that every adorne wireless

device LED in the room is white.

2. Press on the ADMHRM4 until its LED ﬂashes orange (about 5 seconds ). You

now have 5 minutes to complete this process.

3. To include or exclude a device press on the device until the LED changes

color. Orange ﬂashing LED = Included in room

Green ﬂashing LED = NOT included in room

If you get to a device and it is NOT ﬂashing, see TROUBLESHOOTING.

4. Return to the remote. Press for about 5 seconds until the status LED stops

ﬂashing orange and begins ﬂashing green rapidly. It ﬂashes for up to 25

seconds. It is now recording the devices controlled by the SEEK button. During

this time, the ADMHRM4 ignores all button presses. When complete, the LED

turns off and all the status LEDs in the room should be green.

Adding an ADMHRM4 to an Existing Room

To an ADMHRM4 in a room where room level scene control is already operating,

the new ADMHRM4 must ﬁrst acquire the House ID (see Adding an ADMHRM4 to

an Existing Installation). Then it must be bound to the existing room as follows:

1. Press on any previously bound room controller or ADMHRM4 room remote

in the room until the LED ﬂashes orange (about 5 seconds ).

2. Press any button on the new ADMHRM4 to wake it up and illuminate its

LED. Verify that the new ADMHRM4 LED is ﬂashing green. All other devices

included in the room are ﬂashing orange. Press on the new ADMHRM4 until

its LED changes color. Orange ﬂashing LED = Included in room

Green ﬂashing LED = NOT included in room

3. Return to the same previously bound ADMHRM4 used in step 1 and press

until the LED changes to solid white (about 5 seconds ). The ADMHRM4

stops ﬂashing orange and begins rapidly ﬂashing green. It ﬂashes for up to 25

seconds. During this time, the ADMHRM4 ignores all button presses. When

complete, the LED turns off.

STANDARD OPERATION

The ADMHRM4 is shipped with most functions preprogrammed for ease of

installation and initial use. This section summarizes the default operation of

the remote. To make changes from this standard operation, such as changing

light levels and including or excluding devices from speciﬁc scenes, see

CUSTOMIZING OPERATION.

Paddle Functions

Use the rocker paddle to begin and end binding functions. It also functions as

an On/Off switch and a master light level Raise/Lower control for the room. All

devices bound to the same room as the ADMHRM4 are included in the paddle

operation (except fan controls).

Scene Button Functions

The smaller buttons, labeled A—D in the illustrations, are used to record and

recall scenes. You can write the function of each button on the label included

with the remote. All devices bound to the same room as the ADMHRM4 are

included in each scene button (except fan controls).

The following illustration shows the default operation for scene set 1-4:

NOTES:

1 Pressing and holding the paddle does not affect the operation of switched

devices. They will maintain their present state.

Tap once: Raise all room

devices to 100% (ON)

Press and hold: Raise the

current scene’s level 1, 2

Press and hold: Lower the

current scene’s level 1

Tap once: Lower all room

devices to 0% (OFF)

Tap once: All room

Dimmers / Switches

to to

100% ON

75% ON

50% ON

25% ON

0% OFF

Press and hold:

Saves the current

device settings as

the scene that is

recalled the next time

you tap this button.

See CUSTOMIZING

OPERATION.

Paddle Scene Buttons

CUSTOMIZING OPERATION

Modify and Save the Light Levels of a Scene

1. Change lighting levels as desired by pressing or on individual devices.

2. Press and hold the desired scene button on the room scene remote until the

LED ﬂashes twice (about 5 seconds ) to save the new settings.

Removing or Adding Devices to a Scene

1. Press on the ADMHRM4 until the LED begins ﬂashing (about 5 seconds ).

2. Press the scene button that you wish to program. LEDs on all wireless adorne

devices begin to ﬂash. You now have 5 minutes to complete this process.

3. To include or exclude a device in the scene press on the device until the LED

changes color. Orange ﬂashing LED = Included in the active scene

Green ﬂashing LED = NOT included in the active scene

If you get to a device and it is NOT ﬂashing, see TROUBLESHOOTING.

NOTE: You must include devices that are off in the room scene if you want

them to turn off when that scene is recalled.

4. Return to the ADMHRM4 used in step 1. Press for 5 seconds or until all the

status LEDs in the room turn green. The ADMHRM4 continues to ﬂash (about

20-25 seconds). Wait for the LED to stop ﬂashing before pressing a button.

Removing or Adding Devices to the Paddle “On” Function

1. Press on the ADMHRM4 until the LED begins ﬂashing (about 5 seconds ).

2. Tap the paddle on the remote. The LEDs on all the adorne wireless devices

begin to ﬂash. You now have 5 minutes to complete this process.

3. To include or exclude a device press on the device until the LED changes

color. Orange ﬂashing LED = Included in paddle operation

Green ﬂashing LED = NOT included in paddle operation

If you get to a device and it is NOT ﬂashing, see TROUBLESHOOTING.

4. Return to the ADMHRM4 used in step 1. Press for 5 seconds or until all the

status LEDs in the room turn green. The ADMHRM4 continues to ﬂash (about

20-25 seconds). Wait for the LED to stop ﬂashing before pressing a button.

5. To test, tap on any room scene controller that is bound to the same room to

switch included devices to on (dimmers go to full bright).

Removing or Adding Devices to the Paddle “Off” Function

ROOM REMOTE

4 FINGERS

When you see in the

instructions, touch

the top of the paddle

as directed.

ROOM REMOTE

4 FINGERS

When you see in the

instructions, touch the

bottom of the paddle

as directed.

1. Press on the ADMHRM4 until the LED begins ﬂashing (about 5 seconds ).

2. Tap the paddle on the remote. The LEDs on all the adorne wireless devices

begin to ﬂash. You now have 5 minutes to complete this process.

3. See step 3 above.

4. See step 4 above.

5. To test, tap on any room scene controller that is bound to the same room to

switch or fade included devices to off (dimmers go to 0%)

BATTERY INFORMATION

The ADMHRM4 operates using two 1.5V Alkaline AAA size batteries. The remote

goes to sleep whenever it is not performing a function. When asleep, its LED is

off. To check battery status, press any button to wake up the remote.

IMPORTANT: Observe the color of the LED immediately after you wake it up.

âWHITE indicates the batteries are good.

âREDindicates the batteries are getting weak and should be replaced.

The battery compartment is on the bottom of the remote. Gently press up on the

battery door latching tab, then lift the cover to expose the batteries. Replace the

batteries using the same brand. Observe the pole orientation (+ - ) illustration on

the bottom of the battery compartment. Wait for the LED to stop ﬂashing before

attempting to use the remote.

TROUBLESHOOTING

During house ID binding, the LED is not flashing on some devices.

â If LED is solid white before initiating house ID binding:

The device already has another house ID. Reset it to the factory default so that

it can be bound to the desired house ID. See “I made a conﬁguration mistake. I

need to start over” on the next page.

â ,I/('LVVROLGRUDQJHDIWHULQLWLDWLQJKRXVH,'ELQGLQJ

The device may be out of range of the initiating device. Add a MRR2

Wireless Repeater to boost signal range.

During binding or customizing, all LEDs stop flashing before I

press .

The 5 minute binding process timer may have expired. Restart the timer by

repeating steps 1 and 2 of the procedure you were using. Notice that the devices

you previously excluded are ﬂashing green; those included are ﬂashing orange;

simply ﬁnish the process from where you left off.

GI made a configuration mistake. I need to start over.

To reset any adorne wireless device to factory default settings, press and hold

until the LED changes to solid orange (approximately 10 seconds). During the

process, the LED ﬂashes orange. When complete, it becomes solid orange. The

device can then be reconﬁgured, exactly like any new device.

Warranty Information

Manufacturer warranties its products to be free of defects in materials and

workmanship for a period of ﬁve (5) years. There are no obligations or liabilities

on the part of manufacturer for consequential damages arising out of, or in

connection with, the use or performance of this product or other indirect damages

with respect to loss of property, revenue or proﬁt, or cost of removal, installation

or reinstallation.

301 Fulling Mill Road Suite G .

Middletown, PA 17057

Phone: 800.321.2343

www.legrand.us/onq

Please

Recycle

03883r2 9/2007

FCC Notice - FCC ID: YV8-ADMHRM4

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Caution: Any changes or modiﬁcations to this device not explicitly approved by

Legrand could void your authority to operate this equipment.

Canadian Department of Communications - IC: 9922A-ADMHRM4

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux condi-

tions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur

de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-

lage est susceptible d'en compromettre le fonctionnement."

This digital apparatus does not exceed the Class B limits for radio noise emis-

sions from digital apparatus set out in the Radio Interference Regulations of the

Canadian Department of Communications.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Andere Handbücher für ADMHRM4

Inhaltsverzeichnis

Andere LEGRAND Controller Handbücher

LEGRAND

LEGRAND Sagane 846 40 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper DCLV2 Service-Handbuch

LEGRAND

LEGRAND EasyIP VADDIO PCC Bedienungsanleitung

LEGRAND

LEGRAND 672 40 Bedienungsanleitung

LEGRAND

LEGRAND 784 28 Bedienungsanleitung

LEGRAND

LEGRAND 0 677 886L Bedienungsanleitung

LEGRAND

LEGRAND VANTAGE RadioLink EasyTouch II ScenePoint DR Bedienungsanleitung

LEGRAND

LEGRAND Celiane Series Kurzanleitung

LEGRAND

LEGRAND Pass & Seymour RFP Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-101 Bedienungsanleitung

LEGRAND

LEGRAND Raritan SRC-0100 Bedienungsanleitung

LEGRAND

LEGRAND 0 698 74L Bedienungsanleitung

LEGRAND

LEGRAND 0 026 72 Bedienungsanleitung

LEGRAND

LEGRAND Mosaic 335 25 Bedienungsanleitung

LEGRAND

LEGRAND Adorne LC7001 Bedienungsanleitung

LEGRAND

LEGRAND 0 484 22 Bedienungsanleitung

LEGRAND

LEGRAND 0 884 07 Bedienungsanleitung

LEGRAND

LEGRAND 0 663 35 Bedienungsanleitung

LEGRAND

LEGRAND 0 261 19 Bedienungsanleitung

LEGRAND

LEGRAND Bticino H4652 Bedienungsanleitung

LEGRAND

LEGRAND radiant WNRCB40 Bedienungsanleitung

LEGRAND

LEGRAND C2G 29977 Bedienungsanleitung

LEGRAND

LEGRAND HD4657M3 Bedienungsanleitung

LEGRAND

LEGRAND 0 883 27 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch