LEGRAND HPM BH2D Bedienungsanleitung

Please read carefully

Warranty

Legrand warrants the following on the Instant Heat from the date of purchase:

• 5-year warranty on materials and workmanship (excluding heat lamps and centre light).

• 2-year warranty on heat lamps and centre light. These goods come with guarantees that

cannot be excluded under the Australian and New Zealand Consumer Laws. You are entitled

to a replacement or a refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired if the goods fail

to be acceptable quality and the failure does not amount to a major failure.

See the Warranty card enclosed with this product for further details.

Customer Service

For all Customer Service and Technical Support

please call Monday to Friday during business hours.

Legrand Australia

1300 369 777

www.hpm.com.au

Legrand New Zealand

0800 476 009

www.hpm.co.nz

ABN: 31 000 102 661

LE12232AAA 09/2020

Ducted Instant Heat 3-in-1

2 Heat Lamp model: BH2DWE

4 Heat Lamp model: BH4DWE

Instruction Sheet

The Ducted Instant Heat 3-in-1 are ceiling mounted heat lamp appliances combining the functions of heater, extraction fan and luminaire.

Read through these instructions completely before commencing installation. Retain for future use.

This product shall be installed by a licensed electrical contractor or similarly qualified person.

CAUTION:

Regulations concerning the discharge of air must be fulfilled. Local building codes may require venting to the outside. The Instant Heat is

for ceiling mounting only, with the lowest point to be at least 2.2 metres above floor level. It is not intended to be installed in wardrobes or

within 300mm of walls. Please note there is a danger of combustion if placed too close to curtains or other flammable materials. Under no

circumstances must the Instant Heat be covered with insulating material within the ceiling space.

Instant Heat must not be installed where there is a possibility of water splashing on to the lamps. Locate in accordance with the

requirements of the Wiring Rules AS/NZS 3000 relating to damp situations. This means that no part may be located directly above any part

of the bath or shower recess or enclosure. For unenclosed showers refer to the Wiring Rules conditions.

Note: Steam will only be removed if there is sufficient flow of air through the room. Ensure adequate inlet openings in the room are

provided, for example through windows, vents or under the door. Air-flow paths from room inlets to fan should ideally pass over

surfaces where condensation may form.

Product Notes

Trouble shooting

1. This product must be installed and used as per these instructions.

2. A switch disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

4. This appliance is intended for household use and similar purposes. It is not suitable for use in an environment heavily laden with dust.

Under these conditions the life of the fan motor can be significantly reduced.

5. This product contains no serviceable parts and no attempt should be made to repair this product. If the product is faulty it should be

discarded.

6. This product must be cleaned periodically from dust and other contaminants with a damp cloth. Aggressive cleaning agents and

solvents should never be used.

7. Airflows listed in this instruction sheet indicate the product performance. Refer to the BCA (Building Code of Australia), or similar,

for the appropriate airflow required for a particular installation.

8. Ventilation products must have an adequate source of external air to ensure correct performance.

9. This product should not be enclosed in thermal insulation as it may cause the unit to overheat.

10. This product has been designed for domestic or similar uses and is not suitable for a commercial installation.

11. Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances.

12. Extended exposure to UV rays (such as exposure to direct sunlight) may cause discolouration of this product.

13. This product is not suitable for installation in hazardous and/or corrosive areas.

14. This product has been designed to operate in ambient temperatures 5°C to 40°C.

15. The material in this product may vary in colour from batch to batch. Colour matching from one batch to another cannot be guaranteed.

16. This product utilises intellectual property in the form of registered designs, trademarks, and/or patents. Such intellectual property

remains the property of Legrand in all cases.

This Instant Heat is fitted with a thermal cut-out to provide over-temperature protection. If the heat lamps begin to switch ON/OFF

intermittently this may indicate the unit was wired incorrectly, allowing the lamps to operate without the fan running. To rectify please

check your installation.

BH2D

BH4D

Box contents

BH2D BH4D

Housing 1 piece 1 piece

Infrared Heat Lamps (275W) 2 pieces 4 pieces

Light globe (7W LED) 1 piece 1 piece

Instruction Sheet 1 piece 1 piece

Warranty card 1 piece 1 piece

Hole-cutting template 1 piece 1 piece

Ducting (3m x Φ150mm) 1 piece 1 piece

Duct holder 1 piece 1 piece

External grille 1 piece 1 piece

Wall switch plate 1 set 1 set

Duct tape and cable ties 1 set 1 set

Specifications

# - measured with 3 m and Φ150 mm ducting.

Note: Airflow will be reduced with bends in duct, squashing of duct, restrictions on replacement air entering the room to be ventilated,

or pressure differentials between the room and outside air and elevation of the outlet duct and grille with reference to the

bathroom heater.

Model: BH2D BH4D

Supply voltage: 230-240 V a.c. 50 Hz

Max. power rating: 840 W max 1570 W max

Airflow#: 180 m3/hr max

Ceiling cut-out: 205 x 395 mm 295 x 355 mm

Projection into ceiling: 205 mm

Required ceiling depth: 300 mm

Fascia Size 440 x 250 mm 400 x 340 mm

Protrusion (excl. lamps) 23 mm

Heat lamps provided: 2 x 275 W 4 x 275 W

Thermal overload protection: 100° C

Draught stopper: Yes

Centre Light provided: 7W LED R80 E27

Weight (excl packaging): 4.3 kg 5.2 kg

Maintenance

Installation

Remove all packaging from the product before commencing installation.

Ensure the circuit has been isolated from the 240 V mains before commencing work.

III. Locating the Instant Heat

Ensure the Instant Heat is installed at least 2.2 m above floor level.

IV. Preparation of the ceiling

Before cutting out the hole consider the orientation of the Instant heat

and the position of the duct outlet. To ensure maximum performance the

following points should be observed:

■minimise the number of bends in the ducting.

■level of the outlet grille should be at the level of the outlet duct.

■ducting should not be squashed.

■avoid sagging of the ducting to prevent water accumulation.

Using the ceiling cut-out template provided, mark the ceiling with a pencil

outline and cut out a hole at the chosen area. In the cut out made mark the

position of the duct holder (see template). Make sure the distance between

the edges and wall is not less than 300mm. Refer to Fig B.

V. Required Clearances

Within the ceiling cavity, there should be a minimum recess depth of

300mm to the roof. Thermal insulation or similar material shall not be

placed on top of the instant heat, and adjacent material shall be kept clear

to a minimum distance of 150mm. Joists, beams and rafters shall not be

cut or notched to install the Instant Heat. Refer to Fig C.

VI. In-house duct connection

Remove the duct holder from the Instant Heat and fit to end of ducting

with the cable tie. Clip the duct holder to the ceiling at the marked

position. Refer to Fig D.

VII. Remove the fascia

Remove all lamps from the unit. Remove the fascia.

Ceiling

Duct holder

Duct

≥300mm

≥100mm

≥150mm

thermal

insulation

Cleaning

Instant Heat should be cleaned every 6 months or more often

to prevent dust build-up.

1. Disconnect power to Instant Heat before cleaning.

2. Wipe lamps and fascia with care using a soft cloth soaked

with neutral detergent. Ensure lamps are cool to touch

before handling.

Replacement parts

Disconnect power to Instant Heat before lamp replacement.

Replacement lamps:

Heat Lamp: L275HLES (275W)

L375HLES (375W)

Centre light: LR80014K or E27 R80 60W max

Switch wall plate: ED770/3FLHCWE (for BH2D)

ED770/4FLHHCWE (for BH4D)

VIII. Wiring

An Excel Life wall switch plate is provided with this product.

When choosing a location ensure the wall plate is not within

arm’s reach or accessible to a person in a bath or shower.

Follow the wiring diagram shown in Fig. E or Fig. F as applicable.

Once the wiring connection has been made to the Instant Heat, use a cable tie to fix

the cabling to the tie point to prevent contact with the hot metal housing. Refer to

Fig G.

IX. Insertion into cavity

Aligning the Instant Heat with the duct holder, carefully slide the unit into the cavity.

Ensure the guides in the Instant Heat body engage with the slots in the duct holder.

Ensure the 4 retractable clips do not catch in the hole cut-out. Refer to Fig H.

X. Once the unit is fully recessed, push out the clips and use a screwdriver to tighten.

Refer to Fig I.

XI. Final Installation

1. Replace the fascia and lamps. Fix the switch plate to the wall.

2. Reconnect power from the mains supply and test for correct operation.

3. Test airflow by holding a piece of tissue paper near the centre light.

Instant Heat

Cat BH2D

Earth

Neutral

Light

Fan

Heat 1

Excel Life

Switch Plate

Instant Heat

Cat BH4D

Earth

Neutral

Light

Fan

Heat 1

Heat 2

Excel Life

Switch Plate

Horizontal Ducting Downward Ducting Vertical Ducting

Note: When the unit is wired as per the wiring diagram (diagram E and F), the

fan will run automatically at a reduced speed when the heat lamps are

switched ON.

CAUTION: Warranty will be void if the instant heat unit is not wired as per

wiring diagram( E or F).

Roof

Vent

I. Cutting a vent

Cut out a 150 mm diameter hole in the external wall or eave.

II. Ducting

The unit can be installed as shown below in Fig. 1. For best results the

outlet should be at the same level or lower than the exhaust fan (fig.1a &

fig.1b). Warning: Vertical ducting with roof vents will result in reduced fan

performance, increased noise and condensation/dripping (fig.1c). Mount

grille and seal any gaps around grille where necessary.

fig.1a. fig.1b.fig.1c.

Fig.1

External

Grille

Duct holder

Dieses Handbuch passt für folgende Modelle

Andere LEGRAND Heizung Handbücher

LEGRAND

LEGRAND HPM R622D1 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung