LEGRAND 4 121 71 Bedienungsanleitung

1/7

87045 LIMOGES Cedex - FRANCE

Telephone : +33 (0)5 55 06 87 87 - Fax : +33 (0)5 55 06 88 88

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

CONTENTS Pages

1. Description - Use .....................................1

2. Range..........................................................1

3. Overall dimensions...................................1

4. Preparation - Connection .......................1

5. General characteristics...........................6

6. Compliance and approvals .................... 7

7. Auxiliaries and accessories................... 7

1. DESCRIPTION - USE

Use:

Enables to remotely control (ON / OFF) loads (like water heater

swimming pool pomp, heaters, charging plug for electric cars…) by

smartphone with Home + Control app and / or by voice via a voice

assistant. This connected version also offers functions such as:

- Energy consumption: automatically energy consumption

information is available for the circuit to whom the connected

contactor is wired to.

- Scheduling: automatic opening and reclosing action scenarios

based on a timeline. (daily/weekly/specific event such as

“holidays”)

Technology:

. Connected contactor with control by single contact, via

smartphone, voice assistants and / or by its own push button on

the front.

Symbol :

2. RANGE

Noise level:

. Noiseless switch: <10bB.

Width:

. 1 module. 17.8 mm wide.

Types of contact:

. Normally open contact type

Rated current:

. 20 A

Rated voltage:

. 100 to 240V AC

Rated frequency:

. 50 / 60 Hz

Poles:

. 1 pole « NO »

2. RANGE

(continued)

Configuration and use:

. Can be used as a " standard " contactor not connected

And /Or

Can be used with:

- Legrand smartphone app

" HOME + CONTROL"

. Available for free on Google Play or App Store

- Voice assistants (compatible with the main voice

assistants of the market).

3. OVERALL DIMENSIONS

4. PREPARATION - CONNECTION

Mounting:

. On symmetrical rail EN / IEC 60715 or DIN 35.

Operating position:

. Vertical, Horizontal, Flat.

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

Requires prior installation

of a “with Netatmo”

connected starter pack or

a Gateway module.

2/7

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

4. PREPARATION - CONNECTION

(continued)

Row positioning:

. The product shape and the positioning of the terminals allow the

passage of single-line, three-lines and plug-in supply busbars in

the upper part of the product. Then, it is possible to freely choose

the position of the connected contactor in the row and to connect

by supply busbar the other devices put on the same DIN rail.

Module maintenance:

. It is possible to switch a connected contactor in the middle of a

row supplied with an upstream busbar without disconnecting the

other devices on the same DIN rail.

4. PREPARATION - CONNECTION

(continued)

Wiring of the upstream terminals:

In case of a remote control done via a wired push button, the

control is done either via C1 and C2 terminals.

Or via a push button through the phase line protected by a circuit

breaker on terminal C1

Warning: Do not wire from Neutral to C1 or C2

Wiring of the power supply and the load (downstream

terminals):

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

1. Unclip the

clamp to put it in

open position

2. Unscrew the

terminals and pull

the device forward

in order to release

it from the DIN rail

3. Pull the device

downward in order to

completely release it

from the prongs of

the busbar

L: IN terminal for the

Line

N: IN terminal

for Neutral

Load : OUT terminal

for the line after

contact (towards Load)

C1 : IN terminal for control command (IN)

Free dry-contact. No power allowed.

C2 : Out terminal self-protected

Line for remote (OUT)

Free dry-contact. No power

allowed.

Advantage: «auto protected

terminals » technology. It is not

necessary to put a 2A protection

3/7

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

4. PREPARATION - CONNECTION

(continued)

Electrical performance:

. Maximum resistive loads: 4800W

. Maximum motor loads: 2400VA

Wireless network:

. Maximum number of connected devices in the network: 100

Wiring diagrams:

«Auto protected terminals » technology. It is not necessary to put

a 2A protection.

. Installation controlled by the energy supplier electric meter:

. Installation for electrical motor:

. Installation for charging electric cars:

4. PREPARATION - CONNECTION

(continued)

Wiring diagrams

(continued)

. Control of heaters through an already installed central remote:

. Cabling in a swimming pool control cabinet:

. Control of a single line standard contactor (>20A):

. Control of a three lines standard contactor (>20A):

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

4/7

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

4. PREPARATION - CONNECTION

(continued)

Recommended tools:

. For the terminals: screwdriver Pozidriv n°1 or flat-blade 4 mm.

. For clamping: screwdriver flat-blade (5,5mm or less) or Pozidriv

n°1

Connection:

. Control and power screw terminals:

- Terminal type: cage

- Depth: 9 mm

- Stripping length recommended: 9 mm

- Screw head: Posidriv n°1 or slotted

- Type of screw: M3,5

- Minimum tightening torque: mini 0.8 Nm / maxi: 1.4 Nm

advised: 1 Nm

Conductor type for remote control terminals (C1, C2):

. Copper cables

Without ferrule

With ferrule

Rigid cable

1x (0.75 to 2.5mm²)

2 x (0.75 to 1.5mm²)

Flexible

cable

1x (0.75 to 2.5mm²)

2 x (0.75 to 1.5mm²)

1 x (0.75 to 2.5mm²)

2 x (0.75 to 1.5mm²)

Conductor type for power terminals (N, L, LOAD):

. Copper cables

Without ferrule

With ferrule

Rigid cable

1x (0.75 to 6mm²)

2 x (0.75 to 2.5mm²)

Flexible

cable

1x (0.75 to 6mm²)

2 x (0.75 to 2.5mm²)

1 x (0.75 to 2.5mm²)

2 x (0.75 to 1.5mm²)

Remote control commands:

. Operation on-site, directly with the front face push-button of the

device.

. Via the Home / Away wireless master switch

. Via smartphone with the Home + Control smartphone app

. By voice through a vocal assistant.

4. PREPARATION - CONNECTION

(continued)

Visualization of the operating mode of the device and

contacts:

. Via the LED, on the push button command

Color

Status

Meaning

OFF

Manual mode and opened

Contact (OFF)

Blue/Off

Slow blinking

Automatic mode and opened

Contact (OFF)

Blue/Green

Slow blinking

Automatic mode and closed

Contact (ON)

Vert

Fixed

Manual mode and closed

Contact (ON)

Visualization of the setup:

. Via the LED on the settings button

Color

Status

Meaning

Red

Fixed

Temporary status. Device not

connected to the radio network

Green

Fixed

Temporary status. Device correctly

paired to the radio network (when

the radio network is still open)

OFF

Normal status. Device paired to

the radio network (when the radio

network is closed)

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

5/7

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

4. PREPARATION - CONNECTION

(continued)

Add a connected contactor in a connected installation

(several steps)

(continued):

. 1/ Beforehand, to create a connected installation you must

install:

Either a gateway module

Or a connected starter pack (drawing of principle, works with

anykind of “with Netatmo”connected starter pack).

. 2/ Beforehand, the general circuit breaker must be turned OFF,

and only after wiring step done, can be powered back ON to

simultaneously power devices and allow them to be connected to

the network.

. 3/ Press and hold the gateway module settings button for more

than 3 seconds, OR in the center of the Home / Away wireless

master switch until the LED turns green, then release the button.

. The configuration LEDs of " ... with Netatmo " devices in the

installation must all light up in fixed green.

4. PREPARATION - CONNECTION

(continued)

Add a connected contactor in a connected installation

(several steps)

(continued):

. 4/ To complete the installation, briefly press the setting button

on the gateway module (or in the center of the Home / Away

wireless master switch) to finalize the installation.

All " ... with Netatmo " devices LED go OFF

Connected contactor resetting to remove it from a

connected installation

. Press and hold over 5 seconds on the setting button until the

LED on the setting button be fixed red. It is no longer paired with

the gateway module or the Home / Away wireless master switch

Other configurations & actions

. All other features and settings such as ; scenarios etc… are

directly explained step by step in the smartphone app.

Labelling:

. Circuit identification by way of a label inserted in the label

holder situated on the front of the product.

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

6/7

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

5. GENERAL CHARACTERISTICS

Marking of the connected contactor:

Markings of the front side :

Terminal markings :

Markings on the upper side

Lateral markings

5. GENERAL CHARACTERISTICS

(continued)

Sectioning distance:

. micro-gap construction contact according to the standard

EN 60669-2-1

Rated insulation voltage (Ui):

. Ui = 250 V~

Degree of pollution:

. 2

Rated impulse withstand voltage (Uimp):

. 4 kV

Influence of altitude :

. No influence up to 2 000 m

Assigned frequency :

. 50 / 60 Hz

Rated operational current (Ie) depending on utilization

category:

. AC-7a or AC1 (heaters) : le = 20 A

. AC-7b or AC3 (electric motors) : le = 10 A

Rated voltage of use (Ue):

. Ue = 100 to 240 V ~

Resistance to short-circuits:

. Presumed short circuit current 1500 A according to EN 60669-2-

. Thermal stress : 15 000 A²s to EN 60669-2-1

Recommendations:

. For the device protection against short circuits according to the

conditional current, it is recommended to use a circuit breaker or

fuse gG rated current  20 A.

Endurance:

. 20 000 000 operations without load

. 100 000 operations cycles AC-7a according to EN 61095

. 100 000 operations cycles AC-7b according to EN 61095.

. 10 000 operations under load SBL650W according to EN 60669-

2-1

. 200 000 operations under " resistive" load according to

EN 60669-2-5

Characteristics of the radio interface:

. Standard IEEE 802.15.4

. Frequencies 2,4 à 2,4835Ghz

. Transmitter output power <100mW

. Distance max between 2 radio devices: 50m in open field

Dielectric resistance :

. 2000V between front face and rail.

. 750V between upstream and downstream

Protection degree:

. Protection index of terminals against direct contacts: IP2X

(IEC/EN 60529)

. Protection index of the front face against direct contacts:

IP3XD (IEC/EN 60529)

. Class II, front panel with faceplate.

. Class of protection against mechanical impacts IK04 (IEC/EN

62262)

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

down

Icon, to easily identify

a connected device in

the electrical panel

board

AX : Rated current for

externally ballasted lamp

loads and another rated

current

7/7

Connected Contactor

Cat. number : 4 121 71 / 4 121 91

5. GENERAL CHARACTERISTICS

(continued)

Vibrations and shaking resistance:

. vibrations : 10 to 55 to 10Hz single amplitude 0.75mm

. Shaking : 1000m / s ²(6 ±1ms)

Plastic material:

. Self-extinguishing polycarbonate.

. Heat and fire resistant according to IEC/EN 60669-2-1, glow-wire test at 960°C

. Classification UL 94 V0 (≥1.5mm)

Ambient operating temperature:

. Min. = - 5 °C Max. = + 45 °C.

Ambient storage temperature:

. Min. = - 40 °C Max. = + 70 °C.

Average weight:

. 78g

Volume when packed:

. 0,62 dm3.

Environmental profile:

. PEP document available

Installation software:

. XL PRO3

6. COMPLIANCE AND APPROVALS

Compliance to standards:

. NF EN 60669-2-1 / IEC 60669-2-1

Environment respect –Compliance with European Union Directives:

. Compliance with Directive 2002/95/EC of 27/01/03 known as "RoHS" which provides for a restriction on the use of dangerous

substances such as lead, mercury, cadmium, hexavalent chromium and polybrominated biphenyl (PBB) and polybrominated diphenyl

ether (PBDE) brominated flame retardants from 1st July 2006

. Compliance with the Directive 91/338/EEC of 18/06/91 and decree 94-647 of 27/07/04

. Compliant with regulation REACH

Conformity with electromagnetic interference (EMC):

. Compliant EN 301 489-1 , IEC 60669-2-5 , NF EN 60669-2-1

Immunity to shock waves

Radio transmission

Immunity to electrical transients in bursts.

Immunity to conducted disturbances induced by radio fields

Immunity to radiated fields

Electrostatic discharge immunity

Immunity to voltage dips and short break

. Compliance mission radiated according to NF EN55032.

Plastic materials:

. Halogen-free plastics.

. Marking of parts according to ISO 11469 and ISO 1043.

. ISO 7000: 2004, Graphical symbols to be used on equipment - Index and synopsis

Packaging:

. Design and manufacture of packaging in accordance with Decree 98-638 of 20/07/98 and Directive 94/62 / EC.

7. AUXILIARIES AND ACCESSORIES

Beforehand, requires the installation of a " connected starter pack " or " a “gateway module".

Technical data sheet: F03037EN/03

Updated on: 31/08/2020

Created on: 04/10/2019

Dieses Handbuch passt für folgende Modelle

Andere LEGRAND Stromverteilungseinheit Handbücher

LEGRAND

LEGRAND Mosaic 775 40 Bedienungsanleitung

LEGRAND

LEGRAND RARITAN PXE Bedienungsanleitung

LEGRAND

LEGRAND 0 281Series Bedienungsanleitung

LEGRAND

LEGRAND MIDDLE ATLANTIC NEXSYS Bedienungsanleitung

LEGRAND

LEGRAND PDU zero U Bedienungsanleitung

LEGRAND

LEGRAND KEOR SPE R/T Bedienungsanleitung

LEGRAND

LEGRAND PX3 Bedienungsanleitung

LEGRAND

LEGRAND 6 46910-CTO Bedienungsanleitung

LEGRAND

LEGRAND 0 734 54 Bedienungsanleitung

LEGRAND

LEGRAND Middle Atlantic Select Series Bedienungsanleitung

LEGRAND

LEGRAND Server Technology PRO3X Bedienungsanleitung

LEGRAND

LEGRAND IME NEMO D4 - EC Bedienungsanleitung

LEGRAND

LEGRAND Raritan PX4 Bedienungsanleitung

LEGRAND

LEGRAND CS102 Bedienungsanleitung

LEGRAND

LEGRAND Server Technology PRO4X Bedienungsanleitung

LEGRAND

LEGRAND Wiremold Power Commander Bedienungsanleitung

LEGRAND

LEGRAND Raritan PX3-1000 Series Bedienungsanleitung

LEGRAND

LEGRAND 10'' Bedienungsanleitung

LEGRAND

LEGRAND MP6-Megabreak Bedienungsanleitung

LEGRAND

LEGRAND PLUGMOLD PM48TC Bedienungsanleitung

LEGRAND

LEGRAND XL3 160 Bedienungsanleitung

LEGRAND

LEGRAND Server Technology PRO3X Bedienungsanleitung

LEGRAND

LEGRAND Raritan PXO Bedienungsanleitung

LEGRAND

LEGRAND 6 461 00-CTO Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung