LEGRAND 0 648 75 Bedienungsanleitung
x1
2 AA batteries
2 x AA - 1,5 V
+ 5° C / + 45° C
PIR
2 - 8 m
5 à 1000 LUX
de 15 s à 15 min
IP 44
Pack contents
Wireless motion sensor
This product is a connected accessory which requires you to buy and install the «... with
Netatmo» connected starter pack and «... with Netatmo» connected power outlets, swit-
ches (with dimmer option) and/or connected lighting micromodules rst.
Specifications
This product can control up to 20
connected switches (with dimmer option),
micromodules, cable outlets and power
outlets «... with Netatmo»
Frequency bands: 2.4 - 2.4835 GHz
Power level: <10mW
Wireless motion sensor
0 648 75
LE11418AA
Do not x the motion sensor to the wall now.
The installation will be nalized on step 6.
Do not insert the batteries now
Start the wireless motion sensor configuration
Press the middle of the wireless master switch until its light briey turns green,
and then stop pressing. The indicator lights on the products which you have wired will
turn green.
Open the front cover
2
The motion sensor light will ash
green and then switch o.
Nota : if the motion sensor ashes green green red, then remove the batteries and
restart on Step 2
Insert the batteries in the wireless motion sensor
A
B
C
D
Make sure that the indicator lights on the wired products are green and not
ashing. If not, go back to step 2 and then comme back to step 4.
Pair the wireless motion sensor to a wired connected product
To pair a wireless motion sensor with a connected light switch, go to step 4.1.1
To pair a wireless motion sensor with a connected micromodule, go to step 4.2.1
To pair a wireless motion sensor with a connected power outlet, go to step 4.3.1
Phase A : Press the ON button on the wireless switch you wish to pair, while tapping it three
times onto the light switch you wish to control.
Phase B : The indicator lights on the two products will ash blue rapidly.
Phase C : The indicator lights on the two products will briey turn blue and stop ashing
Phase D : the light on the wired product will turn green again and the light on the wireless
motion sensor will switch o. The pairing was successful.
4
4.1.1 Pair a wireless motion sensor with a connected light switch
B
A
D
C
Press the ON and OFF buttons of the wireless motion
sensor to check if the light turns on and o correctly. If it
doesn’t, come back to step 4.1.1.
4.2.1 Pair a wireless motion sensor with a connected micromodule
Phase A : Press the ON button on the wireless switch you wish to pair, while tapping it
three times onto the micromodule you wish to control.
Phase B : The indicator lights on the two products will ash blue rapidly.
Phase C : The indicator lights on the two products will briey turn blue and stop ashing
Phase D : the light on the wired product will turn green again and the light on the wireless
motion sensor will switch o.
4.1.2 Check the correct pairing
5
D
B
A C
4.3.1 Pair a wireless motion sensor with a connected power outlet
Phase A : Press the ON button on the wireless switch you wish to pair, while tapping it three
times onto the power outlet you wish to control.
Phase B : The indicator lights on the two products will ash blue rapidly.
Phase C : The indicator lights on the two products will briey turn blue and stop ashing
Phase D : the light on the wired product will turn green again and the light on the wireless
motion sensor will switch o.
Press the ON and OFF buttons of the wireless motion
sensor to check if the light turns on and o correctly. If it
doesn’t, come back to step 4.1.1
4.1.2 Check the correct pairing
6
Multiple pairing
You can control several connected switches, micromodules and power outlets by repeating
the step 4 on each product you wish to control.
Complete the configuration
To complete your installation,
briefly press the middle of thewireless master switch.
All the indicator lights on the products switch off.
7
60 mm
Ø 3,5 mm maxi
Ø 6,5 mm
2,5
10
m60
6
10
m6
Recommended places
Fix the motion sensor
For optimal use, the motion detector should be placed at a height of approximately 2.50
m from the ground.
8
To increase the time that the
associated product remains
ON (eg, light), turn the screw
(potentiometer) clockwise.
Set up the motion sensor
Time delay
Ambient light sensitivity
Movement sensitivity
8.1 Adjust the ambient light sensitivity
9
By default, the motion detector is set to a minimum delay (15 seconds), a maximum
light sensitivity (1000 lux) and a maximum sensor sensitivity (8 meters). If you want
to change these settings, fol-
low the steps below.
8.2 Adjust the ambient light sensitivity
8.3 Adjust the motion sensor sensitivity
In order for the sensor to detect only when it is dark, turn the screw (potentiometer)
counterclockwise.
To reduce the sensitivity of the motion sensor, turn the screw (potentiometer)
counterclockwise. The detection will then be at a shorter distance.
10
LEGRAND - Pro and Consumer Service - BP 30076
87002 LIMOGES CEDEX FRANCE • www.legrand.com
www.legrand.fr
Close the front cover
To add a connected product to your connected installation,
you should follow the instructions :
- in the Legrand Home + Control application (Settings/Add a new product section)
- or consult the user manual on legrand.fr
11
Red led light : low
battery (*)
(*) 2 years batteries lifetime for 50
detections per day with a time delay of
3 minutes
SIMPLIFIED EU DECLARATION OF CONFORMITY
The undersigned,
Legrand
declares that the radio-electric equipment referred to in these instructions complies with directive 2014/53/EU.
The full text of the EU declaration of conformity
is available on the following website :
www.legrandoc.com
Batteries replacement
Andere LEGRAND Sicherheitssensor Handbücher
LEGRAND
LEGRAND Tynetec ZXT494 Bedienungsanleitung
LEGRAND
LEGRAND CP Electronics EBMHS-BLV Bedienungsanleitung
LEGRAND
LEGRAND Wattstopper FDP-301SR Bedienungsanleitung
LEGRAND
LEGRAND CP Electronics Casambi EBDMR-CB-DD Bedienungsanleitung
LEGRAND
LEGRAND Celiane Series Bedienungsanleitung
LEGRAND
LEGRAND CP Electronics EBDRC-DD Bedienungsanleitung
LEGRAND
LEGRAND CP Electronics EBDHS-AT-PRM Bedienungsanleitung
LEGRAND
LEGRAND WattStopper LMUC-100-2 Bedienungsanleitung
LEGRAND
LEGRAND 088230 Bedienungsanleitung
LEGRAND
LEGRAND 3445 Bedienungsanleitung
LEGRAND
LEGRAND Wattstopper PW-311-U Bedienungsanleitung
LEGRAND
LEGRAND 048822 Bedienungsanleitung
LEGRAND
LEGRAND EMOS G1110 Bedienungsanleitung
LEGRAND
LEGRAND CP Electronics MWS6-KNX Bedienungsanleitung
LEGRAND
LEGRAND Plexo 695 01 Bedienungsanleitung
LEGRAND
LEGRAND SANUS SAL-IWP2 Bedienungsanleitung
LEGRAND
LEGRAND SALARM SL532072 Bedienungsanleitung
LEGRAND
LEGRAND 0 489 54 Bedienungsanleitung
LEGRAND
LEGRAND 0 489 59 Bedienungsanleitung
LEGRAND
LEGRAND Celiane 670 92 Bedienungsanleitung
