LEGRAND Radiant Bedienungsanleitung

Smart Plug-In Outdoor

Switch, Wi-Fi

before you start

Review this guide in its entirety. Consult an electrician with any questions or if

you are unsure of your abilities.

Caution: To reduce the risk of injury and/or overheating and damage to

other equipment:

• Connect the smart plug-in switch to a 120 VAC, 60 Hz power source ONLY.

• To reduce the risk of electric shock, this equipment has a grounding type

plug that has a third (grounding) pin. This plug will only ﬁt into a grounding

type outlet. If the plug does not ﬁt into the outlet, contact a qualiﬁed

electrician to install the proper outlet. Do not change the plug in any way.

• Before installation, ensure there is sufﬁcient Wi-Fi signal strength of at

least two bars. Using a smartphone or tablet on the same Wi-Fi network,

go to the device intended location and check signal. If signal is weak, you

may need a Wi-Fi Extender.

For installation support visit:

www.legrand.us/radiant/smart-lighting/support.

general

Legrand’s Smart Plug-In Outdoor Switch with GFCI function provides personal

ground fault protection. Conventional over-current protection devices such

as fuses and circuit breakers cannot protect people from electrical shock.

Those devices are designed to disconnect the power when currents of several

amperes ﬂow from the hot wire to ground. However, currents as low as a few

milliamperes can be dangerous to normal healthy human beings. One ampere

equals 1000 milliamperes.

Many electrical shocks occur when the path of current ﬂow is from the hot wire

through the metal housing of a defective tool or appliance, through the body of

a human being to the ground. Because of the resistance of the human body to

electrical current ﬂow, the current will be quite low relative to that required to

cause conventional over-current protection devices to function. However, it is

likely to be high enough to cause a painful or possibly lethal electric shock to a

human being.

Legrand’s Smart Plug-In Outdoor Switch is designed to remove power from

the equipment loads when these loads have a potentially lethal ground current

in excess of 6 milliamperes. Normal loads will draw current from the Hot

Conductor (black wire) and return it to the power source through the Neutral

Conductor (white wire). Faulty loads can return some of the current to the power

source through a ground path such as a water pipe, gas pipe, wet ﬂoor, third

conductor (green wire), or worst of all, through a person who is in contact with an

extrinsic ground.

The Legrand Smart Plug-In Outdoor Switch’s rugged construction allows it to

be used in outdoor or indoor locations, where ground fault protection is desired.

When energized by actuation of the reset button, it will conveniently supply power

to any power tool or appliance whose load requirement does not exceed rated

voltage and currents.

installation

1|Plug unit into 120 VAC power socket protected by fuse or circuit breaker.

2| With no load connected the unit will automatically become energized and

the indicator will blink green and amber after 10 seconds.

3| Press “Test/Off” button.

4|Verify the lamp indicator changes to blink white and amber

(this step denotes that power is off).

5| Press and release “Reset/On” button for use.

6| Connect the desired load equipment to cord receptacle and operate

equipment normally.

NOTE: All three plugs are controlled together.

setup up your system

aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is

available on the App Store or on Google Play.

bConnect your Smart Plug-In Outdoor Switch to your home network by

following the step by step instructions in the app.

cUse the app to control your Smart Plug-In Outdoor Switch.

Google Play and the Google Play logo are trademarks of Google LLC.

App Store is a service mark of Apple Inc., registered in the U.S. and other countries.

SCAN TO WATCH HOW

TO SET UP THE APP

SCAN TO DOWNLOAD

getting to know your switch

Item Name Description

1 LED Locator Light

• Indicates the current state of the device.

See LED locator Light Explanations for

detail.

2 Off Button • Turns the device off. Also used to test GFCI

function.

3 On Button • Turns the device on. Also used to reset the

GFCI function.

LED LOCATOR LIGHT EXPLANATIONS

LED

Color

State of

Light Explanation

Green Blinking

Amber

Device is attempting to

connect to the network.

Solid White Device is connected to

network and is off.

Solid Green Device is connected to

network and is on.

Solid Red

Device is off due to

ground fault. Determine

fault and press RESET.

warnings

If the GFCI fails to trip when the Test button is pressed (lamp indicator fails to

turn white) or, if the GFCI fails to reset when the Reset button is pressed (lamp

indicator fails to remain green), the device should be replaced.

If the GFCI tests properly without any appliance plugged into it, but trips each

time the appliance is plugged in, the appliance has a ground fault and needs

to be repaired or replaced. DO NOT BYPASS THE GFCI. IF THIS CONDITION

OCCURS, A REAL SHOCK HAZARD MAY EXIST.

cautions

1. Do not connect any electrical cord longer than 250 feet to the GFCI output

receptacle in order to avoid possibility of nuisance tripping.

2. This GFCI device is to be used on 120V/60Hz circuit only (such as normal

house-hold electrical distribution system).

3. Ground fault circuit interrupters, whether this device or any other, cannot

protect against electrical shock resulting from contact with both hot and

neutral wires of the electrical circuit nor against defects in any wiring

supplying the device.

4. DO NOT USE IF THE BUTTON BOOTS OR CASE OR CORD HAVE

BEEN DAMAGED.

5. Test frequently and at least before each use of load equipment to ensure

correct operation.

6. The GFCI is designed as a protective device.

7. Do not use on circuit with life support apparatus.

regulatory information

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

a minimum distance of 20 cm between the transmitter’s radiating structure(s)

and the body of the user or nearby persons.

NOTE: Any changes or modiﬁcations to this device that are not expressly approved

by the manufacturer will void the warranty and the user’s authority to operate

the equipment.

FCC ID: A3LCWAM210S

IC NOTICE

This device complies with Industry Canada license-exempt RSS standards.

Operation is subject to the following two conditions: (1) this device may not

cause interference; and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT

This equipment meets the SAR evaluation limits given in RSS-102 Issue 5

requirements at the minimum separation distance of 15 mm to the human body.

Note: Any changes or modiﬁcations to this device that are not expressly approved

by the manufacturer, will void the warranty and the user’s authority to operate

the equipment.

IC ID: 649E-CWAM210S

WiFi®is a registered trademark of Wi-Fi Alliance®.

speciﬁcations

Load Rating

Resistive 120 VAC, 60 Hz,15 A

Incandescent/halogen 1800 W

Ballast 15 A standard/electronic

Motor ½ HP

LED 5A

Legrand reserves the right to change speciﬁcations without notice.

notes

Legrand’s Smart Plug-In Outdoor Switch will provide protection against ground

faults when used with a 2-wire outlet receptacle and a 3-wire to 2-wire adapter.

It is always desirable when possible to use a 3-wire grounded receptacle

because a ground provides additional protection against electrical shock

hazard. The adapter should be of the type that can be grounded to the outer

mounting plate screw.

The GFCI does not sense ground faults in the input conductors, therefore it is

recommended that if any extension cords are used, they should be connected

between the GFCI’s output and the tool or appliance to be powered. Your GFCI is

now ready to test and use.

Andere Handbücher für radiant

Inhaltsverzeichnis

Andere LEGRAND Schalten Handbücher

LEGRAND

LEGRAND In One Celiane 672 56 Bedienungsanleitung

LEGRAND

LEGRAND Radiant Series Bedienungsanleitung

LEGRAND

LEGRAND In One Sagane 845 42 Bedienungsanleitung

LEGRAND

LEGRAND MyHome F524 Bedienungsanleitung

LEGRAND

LEGRAND 4126 02 Bedienungsanleitung

LEGRAND

LEGRAND PRO 21 7756 36 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper HDLS1SS Bedienungsanleitung

LEGRAND

LEGRAND adorne WNAL23 Bedienungsanleitung

LEGRAND

LEGRAND Pass & Seymour OSR300S Bedienungsanleitung

LEGRAND

LEGRAND Celiane 67 Series Bedienungsanleitung

LEGRAND

LEGRAND 3 109 53 Bedienungsanleitung

LEGRAND

LEGRAND Raritan MCD-108 Bedienungsanleitung

LEGRAND

LEGRAND DW-311 Bedienungsanleitung

LEGRAND

LEGRAND Soliroc 778 51 Bedienungsanleitung

LEGRAND

LEGRAND pass & seymour LightSense PSWS Bedienungsanleitung

LEGRAND

LEGRAND 695 03 Bedienungsanleitung

LEGRAND

LEGRAND 036 12 Bedienungsanleitung

LEGRAND

LEGRAND XMS-2624P Bedienungsanleitung

LEGRAND

LEGRAND 0 884 07 Bedienungsanleitung

LEGRAND

LEGRAND DPX3 250 Bedienungsanleitung

LEGRAND

LEGRAND Raritan RSS4-102 Service-Handbuch

LEGRAND

LEGRAND WattStopprer RS-150U Kurzanleitung

LEGRAND

LEGRAND Valena Allure 7 525 90 Bedienungsanleitung

LEGRAND

LEGRAND PRO 21 7756 11 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

LEGRAND radiant Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken