Leica TPS 1000 Series Bedienungsanleitung

USER MANUAL

1000Z01

TCA 1800

TPS - System 1000

System

Version 2.2

English

2TPS-System 1000-2.3.1en © Leica

Congratulations on your purchase of a

TPS - System 1000.

This manual contains important safety directions (refer

to chapter "Safety directions") as well as instructions

for setting up the instrument and operating it.

Read carefully through the User Manual before you

switch on the instrument.

TPS - System 1000

System

Electronic theodolites and total stations

The instrument model and the serial number of your

product are indicated on the label in the battery

compartment.

Enter the model and serial number in your manual and

always refer to this information when you need to

contact your agency or authorized service workshop.

Type: ___________ Serial number: ___________

Product identification

4TPS-System 1000-2.3.1en © Leica

The symbols used in this User Manual have the

following meanings:

DANGER:

Indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation or an

unintended use which, if not avoided, could result in

death or serious injury.

CAUTION:

Indicates a potentially hazardous situation or an

unintended use which, if not avoided, may result in

minor or moderate injury and / or appreciable material,

financial and environmental damage.

Important paragraphs which must be adhered to in

practice as they enable the product to be used in a

technically correct and efficient manner.

Symbols used in this manual

Leica TPS-System 1000 Registration Card

Part 1 This card comprises two parts:

- Retain part 1 for your records

- Return part 2 to Leica Geosystems AG, CH-9435

Heerbrugg, Switzerland - Your name and address, the

serial number of the instrument will be registered and

you will receive confirmation of this registration. -

Your local Leica representative will also receive

confirmation

Act immediately

Complete and return part 2 to ensure that you receive

software support. If you do not, you will not be

registered and Leica will not be able to provide the

support that you may need.

Software support

Once your name, your address and the serial number of

the instrument are registered Leica will, at its discretion,

provide you with the following support free of charge:

- Instructions about any corrections and/or

modifications that are necessary for the correct

functioning of the software as supplied to you.

- Disks containing corrections and/or modifications

necessary for the correct functioning of the software

as supplied to you.

6TPS-System 1000-2.3.1en © Leica

Limit to software support

Once your name, address and instrument are registered

Leica undertakes to provide reasonable support for the

software as supplied to you. This software support does

NOT extend to upgrades to new versions of software as

may be introduced by Leica in the future.

Upgrade, enhancement, and exchange programs

Only registered users will receive automatic notification

of possible future product enhancements.

Change of address

Should you change your address after registering for

software support, please write to Leica Geosystems AG,

CH-9435 Heerbrugg, Switzerland,

fax no +41 71 727 46 73, giving details of your new

address, telephone and telefax numbers.

Part 2

Instrument type Software versions:

Serial number System SW V

Date purchased Standard programs:

Company name / Address Orientation V

Resection V

Stakeout V

Tie distance V

Contact persons

Telephone

Telefax

(Please write clearly or use the Company stamp)

Please fill in the coupon below and send the original or

a copy to the address on the other side or fax it to +41

71 727 3605.

8TPS-System 1000-2.3.1en © Leica

Software-Support Registration

Geodesy Division (3681)

Leica Geosystems AG

CH-9435 Heerbrugg

Switzerland

View of chapters

Contents 10

Introduction 15

Instrumentdescriptions 17

Preparing to measure, setting up 22

First steps 31

System concept 37

Operating concept 41

Instrument operation 61

Automatic Target Recognition 143

RCS (Remote Controlled Surveying) 161

Guide Light EGL1 173

Checking and adjusting 175

Care and transport 201

Battery charging 203

Data format 205

Safety directions 219

Technical specifications 240

Index 249

10 TPS-System 1000-2.3.1en © Leica

Contents

Introduction 15

Area of applicability of this User Manual 16

Instrumentdescriptions 17

T - Version 17

TM - Version 18

TC - Version 19

TCM - Version 20

TCA - Version 21

Preparing to measure, setting up 22

Unpacking 22

Charging battery 23

Preparing to measure T- and TM - Versions 23

Preparing to measure with TC, TCM and

TCA - versions 25

Setting up the instrument 26

Tribrach with optical plummet 26

Tribrach without optical plummet 28

Laser plummet in instrument 29

First steps 31

Switching on the instrument 31

Levelling-up with the electronic bubble 32

Installing a distancer (EDM) 33

Measuring distances and angles 35

Summary of the first steps 36

System concept 37

Software architecture 37

Memory concept and data flow 38

Operating modes 39

GeoBasic 40

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Leica Sicherheitssystem Handbücher

Leica

Leica LLD 2 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung