Leister Diode S Bedienungsanleitung
1
LEISTER Diode S, Diode PID
Hot Air Tool
Please read operating instructions carefully
before use and keep for further reference.
• The LEISTER Hot Air Pistol Diode S, Diode PID is designed for continuous
operation and is suitable as a hand tool or for building into machines, instal-
lations and appliances
•Welding of thermoplastic materials and also single-ply flexible plastics and
modified bitumen in the form of boards, tubes, profiles, lining membranes,
coated materials, films, foams, tiles, and sheets. The following procedures
are possible: overlap welding, welding with rod, with tape, butt welding
and melt welding
•Heating-up for forming, bending and sealing of thermoplastic semi-
finished materials and plastic granules
•Drying of water-damp surfaces
•Shrinking of heat-shrink sleeves, films, tapes, solder sleeves and moulded parts.
•Soldering copper pipes, solder joints and metal foils
•Activating/dissolving of solvent free adhesives and fusion adhesives.
• Separating and fusing synthethic fibres and fabrics
• Removing plastic mould flash and putting a shine on plastic surfaces
LEISTER Diode PID
• Temperature electronically
steplessly controlled
• Digital display of SET and
ACTUAL value °C
(in °F on request)
• Air flow monitoring
• Element protection
• Heat protection tube
LEISTER Diode S
• Temperature steplessly
adjustable
• Element protectoion
• Heat protection tube
GB
OPERATING INSTRUCTIONS
APPLICATION
®
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/
Switzerland
Tel. +41- 41 662 74 74 Fax +41- 41 662 74 16
www.leister.com [email protected]
Voltage V~
Capacity W
Frequency Hz
Temperature °C
Air flow l/min.
Air pressure Pa
Weight g
Size mm
42, 100, 120, 230
900, 1350, 1600, 1600
50/60
20 – 600
min. 40
max. 10 5
(
dynamic)
425, 1150 with 3 m cord and 3 m air hose
265 x Ø 40
2
Mains voltage cannot
be switched ove
TEST SIGNS
TECHNICAL DATA
105 Pa = 1 bar
This tool is CCA certificated (CENELEC Certification Agreement).
Electrical safety: double insulated
Danger to life when opening the tool, as live compo-
nents and connections ar exposed. Unplug the tool
before opening it.
Incorrect use of hot air blowers can cause fire and
explosion hazard, especially near combustible materials
and explosive gases.
The tool must be operated with supervision. Warmth
can reach combustible materials, which are out of sight.
For personal protection on building sites we strongly
recommend the tool be connected to a GFCI (Ground
Fault Circuit Interrupter) or a RCCB (Residual Current
Circuit Breaker) .
The voltage rating stated on the tool must correspond to
the line/mains voltage.
Do not touch the element housing and nozzle when
they are hot as they can cause burns. Let the tool cool
down. Do not point hot air flow in the direction of
people or animals.
Protect tool from damp and wet.
FI
120
230
WARNING
CAUTION
Operating Condition
• Air supply
The Hot Air tool Diode «S», Diode «PID» needs either the High Pressure Blower
LEISTER Minor, Longlife or Robust for air supply. In dusty air, air filter must be fitted.
When using compressed air, an oil and water filter must be connected. The air flow
can be steplessly adjusted with the LEISTER air flow adjuster attached to the
blower.
•As required, fit appropriate nozzle.
• Connect tool to the mains.
• Adjust the hot air temperature by use of the potentiometer (3).
The themperature can be checked with a thermocouple about 5 mm inside the nozzle, when using round
nozzles in the centre of the nozzle, when using draw nozzles in the main nozzle opening. The diameter of
the thermocouple must not be more than 1 mm max. (in accordance with DVS 2208 part II).
ATTENTION
•The Hot Air tool should be placed on a heat resistant surface or use LEISTER tool
stand . The tool must not be operated without air supply.
•Allow the Hot Air tool to warm up for about 3 min.
Digital-display (8)
Description of tool
3
USAGE LEISTER Diode S, Diode PID
1. Cord to mains
2. Air hose internal Ø 14 mm
3. Potentiometer for
temperature adjustment
4. Hose clamp
5. Handle
6. Tapered element housing
7. Heat protection tube
8. Digital display of SET and
ACTUAL value
1
2
5
78
7
6
3
4
ACTUAL value
SET value
Resolution 2/3 °C / 5 °F
Air-Error
when air flow falls below
minimum
Sensor Error
when max. temperature
is exceeded in build-up
phase
Operation
•The LEISTER Company, as well as the Service Centres, offer free training courses
and advice in all areas of application (see page 1).
• Allow the tool to cool down after use.
Change of nozzles
•Before changing nozzles, allow the tool to cool down, or use only combination
pliers/spanner.
•Do not touch hot nozzle and make sure to put it only on a heat resistant surface,
because of the fire hazard.
•Only LEISTER nozzles should be used.
• Tool stand
• PVC air hose Ø 14 mm
•Hose clamp for air hose Ø 14 mm
•Repairs should only be carried out by authorised LEISTER Service Centres. They
guarantee a specialised and reliable Repair Service within 24 hours using original
spare parts lists.
•Guarantee and liability will be in accordance with the guarantee certificate as
well as the current valid general business and sales conditions.
•The LEISTER Company rejects any guarantee claims for tools which are not in their
original condition. The tools must never be altered or changed.
Technical data and specifications are subject to change without prior notice.
Your authorised Service Centre is:
GUARANTEE AND LIABILITY
SERVICE AND REPAIR
TYPES
ACCESSORIES
4
BA DIODE S/DIODE PID/06.2001/GB
Tapered element
housing with heat
protection tube for
push-fit LEISTER
nozzles.
Element housing
with heat tube
protection for
screw-on LEISTER
nozzles
®
Tool stand
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/
Switzerland
Tel. + 41- 41 662 74 74 Fax +41- 41 662 74 16
www.leister.com [email protected]
Andere Handbücher für Diode S
4
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Leister Elektrowerkzeuge Handbücher
Leister
Leister TRIAC AT Bedienungsanleitung
Leister
Leister TRIAC AT Bedienungsanleitung
Leister
Leister TRIAC AT Bedienungsanleitung
Leister
Leister GHIBLI AW Bedienungsanleitung
Leister
Leister GHIBLI AW Bedienungsanleitung
Leister
Leister WELDPLAST S4 Bedienungsanleitung
Leister
Leister Electron Bedienungsanleitung
Leister
Leister Diode Bedienungsanleitung
Leister
Leister TRIAC ST Bedienungsanleitung
Leister
Leister TRIAC AT Bedienungsanleitung
Leister
Leister SOLANO AT Bedienungsanleitung
Leister
Leister WELDMAX Bedienungsanleitung
Leister
Leister TRIAC AT Einrichtungshandbuch
Leister
Leister LE 40 000 Bedienungsanleitung
Leister
Leister Electron Bedienungsanleitung
Leister
Leister SONORA S1 Bedienungsanleitung
Leister
Leister GHIBLI AW Bedienungsanleitung
Leister
Leister ELECTRON ST Bedienungsanleitung
Leister
Leister UNIROOF 700 Bedienungsanleitung
Leister
Leister TRIAC ST Bedienungsanleitung
