Leitner LH670 Bedienungsanleitung
1
LH670/675
2
CONTENTS
Headset controls 4
Charging base 5
Indicator lights 6
Audio signals 7
Set up your headset 8
Make a call 11
Answer a call 12
Use UniBase®Technology 13
Control your volume 14
Activate auto-on feature 15
Turn on call control 15
Register a new primary headset 18
Connect a 2nd headset for conference calls or training 16
Health and Safety Instructions 21
Troubleshooting & Frequently Asked Questions 19
How to...
Understanding your...
4
Speaker Volume Up & Mute
Speaker Volume Down & Mute
FocusLight
Headset ON/OFF
Battery
Battery Door
UNDERSTANDING YOUR
HEADSET CONTROLS
Headset
Charging Base
Lithium-Ion Battery
Battery Door
8.5v AC Adaptor
RJ-9 Phone Cord
Type C-to-A USB Cord
WHAT’S IN
THE BOX
A
B
C
D
E
F
A
B
C
D
E
F
5
Battery Indicator
Computer Mode Button
Bluetooth Mode Button
Telephone Mode Button
Bluetooth Connection Light
Charging Cradle
USB Connector Port
Power Port
EHS and Handset Lifter Port
Telephone Connector Port
Handset Connector Port
Microphone Volume Up/Down
Accessory Selection Switch
Compatibility Switch
UNDERSTANDING YOUR
CHARGING BASE
5
7 8 ９
2 3
14
2
1
3
4
5
6
7
8
９
10
11
12
10 11
12
6
13
14
13
14
6
Battery Lights %
Device Lights
Telephone mode
4 solid lights = 100% charge
3 solid / 1 flashing lights = 75% charge
2 solid / 2 flashing lights = 50% charge
1 solid / 3 flashing lights = 25% charge
4 flashing lights = less than 25% charge
Computer mode
UNDERSTANDING THE
INDICATOR LIGHTS
Bluetooth ode
Bluetooth connection light
7
UNDERSTANDING THE
AUDIO SIGNALS
SOUND
2 quick beeps (60 sec repeat)
2 beeps
2 pitch tone
2 rapid beeps
1 beep
1 beep
2 pitch tone (8 sec repeat)
Low battery
Nearly out of range
Out of range
Back in range
Receiver volume up/down
Mute off/on
Mute is on
WHAT IT MEANS
When you walk out of range of the base, you will hear warning beeps in the
headset. If the headset disconnects due to being out of range, the call will not
drop. The headset will automatically reconnect when you are back in range.
NOTE: If you do not move back in range within 5 minutes, the call will disconnect.
8
HOW TO
SET UP YOUR HEADSET
1Plug the power adaptor into the charging base. The power light on the base will
light up. We recommend charging your headset for at least 4 hours before use.
2a CONNECTING TO A TELEPHONE WITH A HEADSET JACK Use the included
connector cord to connect the telephone port on the base to the headset port
on your desk phone. You may need to adjust the compatibility switch on the
bottom of the base to find the correct setting for your phone model. Most
phones use 1. Cisco phones should be set to 4 when using the headset jack.
Power socket Telephone port
Compatibility switch
2b CONNECTING TO A TELEPHONE WITHOUT A HEADSET JACK Connect
the curly cord of your handset to the handset port on the charging base. Use the
included connector cord to connect the telephone port on the the charging base
to the handset jack on your desk phone. See 2a on using the compatibility switch.
Handset port
9
3CONNECTING TO A LEITNER HANDSET LIFTER (OPTIONAL) Connect your
headset to your desk phone as shown in Step 2b. Attach the handset lifter to
your desk phone and connect it to the AUX port on the charging base. Set the
accessory selection switch on the bottom of the base to RHL. See the included
user guide or go to headsets.com/LifterSetup for more help.
Accessory selection switch
AUX port
CONNECTING TO A LEITNER ELECTRONIC HOOKSWITCH (EHS) CABLE
(OPTIONAL)*Each office phone is a bit different so please refer to the EHS cable
instructions for quick and easy setup.
* With a handset lifter or EHS cable connected, you’ll be able to answer and end calls
using the ON/OFF button on the headset—up to 350 feet away from your desk!
4
10
5CONNECTING TO YOUR COMPUTER Use the included USB cable to connect
the charging base to an available USB port on your computer. If your computer
doesn’t recognize the device after a minute, go to your sound settings and select
“Leitner Headset” as both your default microphone and default speakers.
USB port
6CONNECTING TO BLUETOOTH With your headset turned off, hold down the
Bluetooth button ( １) for three seconds until the light starts flashing. Make sure
Bluetooth is enabled on the device you're trying to connect to. Select 'Leitner
Headset' from the list of available devices ( 2). The light on your charging base
will stop flashing once it's successfullly connected.
1
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Leitner Headset Handbücher
Leitner
Leitner LH280 Bedienungsanleitung
Leitner
Leitner LH270 Bedienungsanleitung
Leitner
Leitner SmartSet 370 Bedienungsanleitung
Leitner
Leitner PREMIUM DONGLE Bedienungsanleitung
Leitner
Leitner LH270 Bedienungsanleitung
Leitner
Leitner LH280 Bedienungsanleitung
Leitner
Leitner LH270 Bedienungsanleitung
Leitner
Leitner SmartSet 370 Bedienungsanleitung
Leitner
Leitner OfficeAlly LH380 Bedienungsanleitung
Leitner
Leitner LH270 Bedienungsanleitung
