Lenovo 43N3424 Bedienungsanleitung

ThinkStation Serial Attached

SCSI Hard Disk Drive

User Guide

http://www.lenovo.com/safety

Note: Before installing the product, e sure to read the warranty information in Appendix

C “Lenovo Limited Warranty” on page 11.

Thrid Edition (December 2014)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered

pursuant a General Services Administration “GSA” contract, use, reproduction, or

disclosure is su ject to restrictions set forth in Contract No. GS-35F-05925.

Contents

Chapter 1. About the ThinkStation Serial Attached SCSI (SAS) hard disk

drive . . . . . . . . . . . . . . . . . . . . . . . .1

Product description . . . . . . . . . . . . . . . . . . . .1

Installation planning. . . . . . . . . . . . . . . . . . . .2

Installation requirements . . . . . . . . . . . . . . . . .2

Partition planning . . . . . . . . . . . . . . . . . . .4

Installing the drive . . . . . . . . . . . . . . . . . . . .4

Step 1. Opening your computer . . . . . . . . . . . . . . .4

Step 2. Unpacking the drive . . . . . . . . . . . . . . . .4

Step 3. Mounting the drive in the bay . . . . . . . . . . . . .5

Step 4. Attaching the cables to the drive . . . . . . . . . . . .6

Step 5. Completing the installation of the drive . . . . . . . . . .7

Preparing the drive for use . . . . . . . . . . . . . . . . .7

Partitioning and formatting your drive . . . . . . . . . . . . .8

Chapter 2. Troubleshooting . . . . . . . . . . . . . . . . 113

Appendix A. PCIe-to-SAS host bus adapter quick installation

instructions . . . . . . . . . . . . . . . . . . . . 115

Appendix B. Service and Support . . . . . . . . . . . . . 117

Registering your option . . . . . . . . . . . . . . . . . 117

Online technical support . . . . . . . . . . . . . . . . . 117

Telephone technical support . . . . . . . . . . . . . . . . 117

Appendix C. Lenovo Limited Warranty . . . . . . . . . . . 119

Warranty information ... . .. . .. . .. . .. . ..126

Lenovo Limited Warranty - Customer

Notice ... . .. . .. . ...128

Appendix E.Notices .................. 143

iii

Appendix D.Electronic emission notices. . . .........139

Recycling information . . .... . . . . . . . . . . . . . 143

Trademarks . . . . . . . . . . . . . . . . . . . ...145

Appendix F. Restriction of Hazardous Substances Directive

(RoHS) . . . . . . . . . . 147

Appendix G. İthalatçı – İmalatçı / Üretici Firma Bilgileri ve Diğer

Bilgiler . . . . . . . . . . . . . . . . . . . . . . . . 149

Appendix H. Servis İstasyonları ve Yedek Parça Malzemelerinin Temin

Edileceği Adresler . . . . . . . . . . . . . . . . . . . 151

iv ThinkStation Serial Attached SCSI Hard Disk Drive User Guide

Chapter 1. About the ThinkStation Serial Attached SCSI

(SAS) hard disk drive

This section provides information on the ThinkStation® Serial Attached SCSI

(SAS) hard disk drive.

Product description

The SAS hard disk drive can only be installed in computers with at least one

of the following configurations:

v a SAS-compatible backplane with bays designed to accommodate SAS hard

disk drives

v a PCI Express (PCIe)-to-SAS host bus adapter

The SAS hard disk drive connects to a SAS-compatible interface which

supports SAS hard disk drives in a single drive per cable configuration. There

are no jumper settings required for master or slave settings.

The SAS hard disk drive uses 29-pin SAS interface connectors. The top surface

1 and the bottom surface 2 of the connector are displayed in the diagram

below. The cables included in the option package enable you to connect the

power port and the signal port of the SAS hard disk drive as Serial ATA

(SATA) hard disk drives.

Your hard disk drive can be configured in one of the following ways:

v As single drive

– Be installed as the only hard disk drive in a computer

– Replace a hard disk drive

v As one of multiple drives to operate with other installed hard disk drives

Notes:

1. SAS hard disk drives can not operate with SATA hard disk drives.

2. Make sure that all the other hard disk drives in your computer are SAS

hard disk drives.

The SAS and SATA drives can not operate together as they have different

spinning speeds, which cause the two drives to place different rotational

vibration forces on the chassis. If a SATA drive of 7200 RPM and a SAS

drive of 15000 RPM are installed in the same chassis, the two different

forces on the chassis could cause performance degradation and

additional acoustic noise.

In addition to this User’s Guide, your option package contains:

v Serial Attached SCSI hard disk drive

v Drive handling flyer

v Safety information manual

v Two SAS cables

Contact your place of purchase if parts are missing or damaged. Be sure to

retain your proof of purchase. It may be required to receive warranty service.

Installation planning

This section contains detailed information to help you plan your SAS hard disk

drive installation.

Installation requirements

To install the SAS hard disk drive, you must have:

v Documentation

The documentation that came with your computer and operating system.

v SAS compatible port

Your computer must have a SAS compatible port on system board or a

PCIe-to-SAS host bus adapter. If you are not sure about your port, see the

documentation that came with your computer. Generally, the ThinkStation

D10 series computer systems have SAS compatible ports on the system

board. The ThinkStation S10 series computer systems need a PCIe-to-SAS

host bus adapter to support SAS hard disk drives.

2 ThinkStation Serial Attached SCSI Hard Disk Drive User Guide

For PCIe-to-SAS host bus adapter installation instructions, see Appendix A,

“PCIe-to-SAS host bus adapter quick installation instructions,” on page 115 or

refer to the documentation that comes with your PCIe-to-SAS host bus

adapter.

SAS hard disk drive cable

You will be required to use one of the following 29-pin SAS connecting

cables included in your option package to connect the SAS hard disk drive

to the power and signal ports:

– Straight connecting cable

– Right angle connecting cable

Chapter 1. About the ThinkStation Serial Attached SCSI (SAS) hard disk drive 3

The straight cable is for the ThinkStation D10 series computer systems.

The power port 1 and the signal cable 2 are displayed in the diagram

below.

The right angle connecting cable is for the ThinkStation S10 series

computer systems. The power port 1 and the signal cable 2 are

displayed in the diagram below.

Partition planning

The two kinds of file systems used by the Microsoft® operating system are

NTFS and FAT32. Microsoft Windows® XP can support both of these file

systems, but Microsoft Windows Vista® can only support NTFS.

Note: NTFS is recommended to be used to partition any new drives.

To determine which file system you are using, do the following:

1. Right-click an exiting drive under My Computer.

2. Select Properties. The file system will be displayed in the General tab.

For more information on partitioning your drive, see “Partitioning and

formatting your drive” on page 8.

Installing the drive

You must install your new drive in the computer before using your operating

system to partition and format your new drive.

The instructions in this section are general guidelines that apply to most

computers. For specific information on installing a hard disk drive in your

computer, see the documentation that came with your computer.

Step 1. Opening your computer

Before opening your computer, complete the following steps:

1. Turn off the computer.

2. Unplug the power cable from the power outlet of your computer and all

other attached devices and cables.

It is now safe to open your computer. For specific information about opening

your computer, see the documentation that came with your computer.

Step 2. Unpacking the drive

Use the following procedure to unpack and handle the drive. To prevent

damage and static-electricity discharge, keep handling to a minimum.

1. Do not open the antistatic bag until you are ready to install the drive. Static

electricity can damage the drive and other computer components.

2. Touch the inner conductive surface of the antistatic bag containing the

drive and your hand to an unpainted metal surface on the computer for

two seconds. This drains static electricity from the bag and from your body.

3. Before handling the drive, ground yourself by touching an unpainted

surface on the computer. Ground yourself again after leaving and returning

to your work area.

ThinkStation Serial Attached SCSI Hard Disk Drive User Guide 4

4. Always handle the drive by its edges. Do not touch any exposed printed

circuitry, components, or connector pins.

5. While installing the drive, avoid all unnecessary handling. Rough handling

can damage the heads, rotating disks, and bearings inside the drive

housing.

6. If you must put the drive down, place the antistatic bag on a flat, padded

surface and place the drive on the bag with the component side facing up.

Note: If you want to install the drive in a 5.25-inch bay, you will need to

purchase a universal bay conversion kit which is available at many local

computer supply stores.

Step 3. Mounting the drive in the bay

You can mount the drive horizontally or vertically based on the location of the

bay in your chassis. The ThinkStation D10 and S10 series computer systems

provide plastic brackets for you to mount your hard disk drives. Alternatively,

you can mount your hard disk drive using screws in a bay without a bracket.

The screws should be commercially available at your local computer retailer.

To mount the drive using the bracket:

1. Pull the bracket out of the bay by pressing the snaps (1) and pulling the

handle (2).

Chapter 1. About the ThinkStation Serial Attached SCSI (SAS) hard disk drive 5

2. Install the drive to the bracket, and make sure the four mounting pins (1)

have already been aligned in the drive screw holes and secured tightly.

3. If you are adding your new drive to a system with an existing hard disk

drive, position the new drive adjacent to and in the same direction of the

existing hard disk drive so that you will not have to twist the interface

cable when you connect the drive.

4. Slide the drive with bracket into the bay until the two snaps of the bracket

are locked in the bay.

To mount the drive using screws:

1. Slide the drive into the bay.

2. If you will add your new drive to a system with an existing drive, position

the new drive adjacent to and oriented in the same direction as the existing

hard drive so that you will not have to twist the interface cable when you

connect the drive.

3. Align the drive-bay screw holes with the threaded holes in the drive

housing or expansion brackets.

4. Hand thread the screws to lightly secure the drive in the bay. For some

installations, it might be necessary to use the screw holes on the bottom

(circuit board side) of the drive.

5. Check the drive alignment and tighten the screws. Do not over tighten.

Step 4. Attaching the cables to the drive

Use the following procedure to attach the cables.

1. Select the right 29-pin cable for your computer (straight cable for the

ThinkStation D10 series computer systems and right angle cable for the

ThinkStation S10 series computer systems).

2. Attach the 29-pin cable to your SAS hard disk drive interface connector.

ThinkStation Serial Attached SCSI Hard Disk Drive User Guide 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lenovo Lagerung Handbücher

Lenovo

Lenovo 43N3417 - 256 GB Hard Drive Bedienungsanleitung

Lenovo

Lenovo ThinkPad Hard Disk Drive Bedienungsanleitung

Lenovo

Lenovo EMC2 px4-400r Bedienungsanleitung

Lenovo

Lenovo 41N3015 - 250GB Serial Ata Hard Disk Drive Bedienungsanleitung

Lenovo

Lenovo D1224 Bedienungsanleitung

Lenovo

Lenovo ThinkServe LTO Bedienungsanleitung

Lenovo

Lenovo USB 2.0 Portable Hard Disk Drive Bedienungsanleitung

Lenovo

Lenovo ThinkSystem DM7100F Handbuch

Lenovo

Lenovo Optical M10 Merkblatt

Lenovo

Lenovo V3700 V2 XP Bedienungsanleitung

Lenovo

Lenovo EMC2 px12-450r Bedienungsanleitung

Lenovo

Lenovo ThinkSystem DM5000 series Handbuch

Lenovo

Lenovo ThinkSystem DM3000 series Handbuch

Lenovo

Lenovo ThinkSystem DE Series Bedienungsanleitung

Lenovo

Lenovo IBM Storwize V7000 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem DM240N Bedienungsanleitung

Lenovo

Lenovo S3200 Bedienungsanleitung

Lenovo

Lenovo 43R2018 - ThinkPad 160 GB External Hard... Bedienungsanleitung

Lenovo

Lenovo F410 Bedienungsanleitung

Lenovo

Lenovo DM7100H Handbuch

Lenovo

Lenovo ThinkSystem Heavy Duty Bedienungsanleitung

Lenovo

Lenovo ThinkPad Hard Disk Drive Bedienungsanleitung

Lenovo

Lenovo px2-300d Bedienungsanleitung

Lenovo

Lenovo Secure Desktop Drive Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung