LevelOne GSW-0509 Bedienungsanleitung

GSW-0509/GSW-0809

5/8-Port Gigabit Switch

V1. 0_20150422

Table Of Contents

1. INTRODUCTION.........................................................3

1.1 Product Briefs .......................................................................................................3

1.2 Product Features....................................................................................................3

1.3 Hardware Introduction..........................................................................................4

2. CONNECTING THE SWITCH....................................6

2.1 Package Contents..................................................................................................6

2.2 Before You Connect to the Network.....................................................................6

3. Connecting the switch ...................................................7

3.1 Switch to End Node or Server ..............................................................................7

4. Appendix....................................................................... 8

4.1 Technical Specifications .......................................................................................8

4.2 RJ-45 PIN SPECIFICATION ...............................................................................9

1. INTRODUCTION

1.1 Product Briefs

The switch is a un-management layer 2 10/100/1000Mbps switch; it provide dedicated 10,

100 or 1000 Mbps Ethernet bandwidth on each port. The ports will automatically detect the

speed, duplex and MDI/MDIX status of the device it is connecting to, and adjust these

settings accordingly. The Switch ports can be used to network computers, printers, servers,

routers, other switches or any device equipped with an Ethernet port. For best performance,

use Category 5 or better Ethernet cabling.

This stand-alone Switch is very easy to set up, there is no network management required.

Just power on the Switch and connect the cables. Keep in mind however that the standard

rules of Ethernet regarding cable length apply to this and all Ethernet devices. The length of

an Ethernet cable from one device to another cannot exceed 100 meters (or 300 feet).

1.2 Product Features

The Switches do not require any management. All Switches are designed for easy

installation, flexibility and high performance. Connect devices to the Switch as the scale and

volume of network traffic increases.

5/8 10/100/1000Mbps Ethernet ports

Auto-Negotiation for 10/100/1000Mbps and duplex mode

Auto-MDI/MDIX for each port

Supports Full/Half-duplex transfer mode for 10 and 100Mbps

Supports Full-duplex transfer mode for 1000Mbps

Full wire speed reception and transmission

Store-and-Forward Switching method

Supports 8K absolute MAC addresses

5-Port Switch Supports 125KB RAM for data buffering

8-Port Switch Supports 125KB RAM for data buffering

IEEE 802.3x flow control for Full-duplex

Back pressure flow control for Half-duplex

Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure,

format, and support for CSMA/CD protocol, full duplex, flow control, and management

objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet

and a hundredfold increase over 10-Mbps Ethernet. Since it is compatible with all 10-Mbps

and 100-Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade

without wasting a company’s existing investment in hardware, software and trained

personnel.

The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping

with the network bottlenecks that frequently develop as computers and their bus speeds get

faster and more users use applications that generate more traffic. Upgrading key components,

such as your backbone and servers to Gigabit Ethernet can greatly improve network response

times as well as significantly speed up the traffic between your subnets.

1.3 Hardware Introduction

1.3.1 Product Appearance

1．Front Panel

The figure below shows the front panel of the Switch.

5-Port Gigabit Switch Front Panel

8-Port Gigabit Switch Front Panel

2．Rear Panel

The figure below shows the rear panel of the Switch. There is a AC inlet in the 5/8-Port

switch rear panel.

5-Port Gigabit Switch Rear Panel

8-Port Gigabit Switch Rear Panel

Auto MDI/MDI-X Ports:

All ports support automatic MDI/MDI-X crossover detection. The AutoMDI/MDI-X function

makes it simple to connect to the switch—just plug either a Crossover or Straight-Through

CAT5 cable into any port.

AC inlet

Power is supplied through external AC power. The input AC voltage is 100~240V.

1.3.2 LED Indicators

Table 1-3 Ethernet Switch LED Indicators

LED

Panel

signature

Status

Description

Power

Indicator

Power

Green ON

Switch is powered ON

OFF

Switch is powered OFF

Speed

1000M

Green ON

1000Mbit/s

Indicator

OFF

1000M no link

Status

Indicator

Link/Act

Green ON

Link

Green Blinking

Activity

OFF

No link path

Loop

Red ON

Network has loops

OFF

Network normal

2. CONNECTING THE SWITCH

2.1 Package Contents

Open the shipping carton of the Switch and carefully unpack its contents.

The carton should contain the following items:

One 5/8 Port 10/100/1000BASE-T Gigabit Ethernet Switch

Four rubber feet with adhesive backing

One power Cord

CD-ROM with product documentation

If any item is found missing or damaged, please contact your local reseller for replacement.

2.2 Before You Connect to the Network

The site where you install the Switch may greatly affect its performance. Please follow

these guidelines for setting up the Switch.

Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs) of

weight. Do not place heavy objects on the Switch.

The power outlet should be within 1.82 meters (6 feet) of the Switch.

Visually inspect the power cord and see that it is fully secured to the AC power port.

Make sure that there is adequate space for proper heat dissipation from and adequate

ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front and

rear of the Switch for ventilation.

Install the Switch in a fairly cool and dry place for the acceptable temperature and

humidity operating ranges.

Install the Switch in a site free from strong electromagnetic field generators (such as

motors), vibration, dust, and direct exposure to sunlight.

When installing the Switch on a level surface, attach the rubber feet to the bottom of the

device. The rubber feet cushion the Switch, protect the casing from scratches and prevent

it from scratching other surfaces.

3. Connecting the switch

Cable Quality

For all connections to the Switch, use these rules to determine the Cable quality.

For connections to 10BASE-T and 100BASE-TX devices, use Category 5 or 5e

UTP/STP cable.

For connections to 1000BASE-T and 100BASE-TX devices, use Category 5e or better

UTP/STP cable.All 1000BASE-T connections operate in full duplex mode.

3.1 Switch to End Node or Server

End nodes include PCs outfitted with a 10, 100 or 1000 Mbps RJ-45 Ethernet/Fast Ethernet

Network Interface Card (NIC) and Ethernet ready routers. Use standard Ethernet cable to

connect the Switch to end nodes. Switch ports will automatically adjust to the hardware

characteristics (MDI-II/MDI-X, speed, duplex) of the device to which it is connected. Switch

connected to an end node

Reference picture

NOTE: UTP (Unshielded Twisted Pair) Ethernet cabling is adequate for

most small office environments. More expensive STP (Shielded Twisted

Pair) can also be used, but is generally only needed where there will be

risk of strong Electromagnetic of Radio Frequency Interference.

4. Appendix

4.1 Technical Specifications

Table 4-1 Ethernet Switch General Features

General

Standards:

IEEE 802.3ab 1000BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3 10BASE-T

IEEE 802.3x Flow Control

Protocol:

CSMA/CD

Data Transfer Rate:

Ethernet:

10Mbps (Half-duplex) 20Mbps (Full-duplex)

Fast Ethernet:

100Mbps(Half-duplex) 200Mbps(Full-duplex)

Gigabit Ethernet:

2000Mbps (Full-duplex)

Topology:

Star

Network Cables:

Ethernet:

2-pair UTP Cat. 3,4,5, Unshield Twisted Pair (UTP )Cable

Fast Ethernet:

2-pair UTP Cat. 5, Unshield Twisted Pair (UTP )Cable

Gigabit Ethernet:

4-pair UTP Cat. 5, Unshield Twisted Pair (UTP )Cable

Number of Ports:

5/8

Table 4-2 Ethernet Switch Physical and Environmental Features

Physical and Environmental

AC Inputs(For 5/8-Port):

100~240VAC; 3.3V/2A

Power Consumption

5-Port: 6.6 watts maximum

8-Port: 6.6 watts maximum

Operating Temperature

0 C ~ 45℃(32F ~ 113F )

Storage Temperature:

-10C ~ 70C (14F ~ 158F)

Humidity:

5% ~ 95% RH, non-condensing

Dimensions:

5/8-Port: 190mm x 120mm x 35mm

EMI

FCC Class B, CE Mark Class B

Safety:

CSA International

Table 4-3 Ethernet Switch Performance Features

Performance

Transmission Method:

Store-and-forward

RAM Buffer:

5-Port : 125KB

8-Port : 125KB

Filtering Address Table:

8K MAC address per device

Packet Filtering/ Forwarding Rate:

Full wire speed

MAC Address Learning:

Self-learning, auto-aging

4.2 RJ-45 PIN SPECIFICATION

The following diagram and tables show the standard RJ-45 receptacle/connector and their pin

assignments.

RJ-45 Connector pin assignment

Contact

Media Direct Interface Signal

Contact

Media Direct Interface Signal

TX_D1+

BI_D3-

TX_D1-

RX_D2-

RX_D2+

BI_D4+

BI_D3+

BI_D4-

Standard RJ-45 receptacle/connector

Andere Handbücher für GSW-0509

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LevelOne Schalten Handbücher

LevelOne

LevelOne FEP-2402 Series Bedienungsanleitung

LevelOne

LevelOne FSW-0803TX Bedienungsanleitung

LevelOne

LevelOne GSW-0504 Bedienungsanleitung

LevelOne

LevelOne GSW-1676 Bedienungsanleitung

LevelOne

LevelOne OfficeCon FSW-0822 Bedienungsanleitung

LevelOne

LevelOne GTP-2871 Bedienungsanleitung

LevelOne

LevelOne 1650 Bedienungsanleitung

LevelOne

LevelOne FEU-0810 Bedienungsanleitung

LevelOne

LevelOne IES-0610 V2 Bedienungsanleitung

LevelOne

LevelOne FEP-0840 Bedienungsanleitung

LevelOne

LevelOne GSW-2473 Bedienungsanleitung

LevelOne

LevelOne GSW-2472TGX Bedienungsanleitung

LevelOne

LevelOne GEL-2871-v1 Bedienungsanleitung

LevelOne

LevelOne GSW-4870TGX Bedienungsanleitung

LevelOne

LevelOne FEP-0311 Bedienungsanleitung

LevelOne

LevelOne FGP-1072 Bedienungsanleitung

LevelOne

LevelOne POH-1250 Bedienungsanleitung

LevelOne

LevelOne GEL-1072 Bedienungsanleitung

LevelOne

LevelOne IES-2881 Bedienungsanleitung

LevelOne

LevelOne FGP-1031 Bedienungsanleitung

LevelOne

LevelOne FSW-1650 Bedienungsanleitung

LevelOne

LevelOne GEL-2060 Kurzanleitung

LevelOne

LevelOne GSW-0840T Bedienungsanleitung

LevelOne

LevelOne ViewCon KVM-0407 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung