Levolor InMotion Bedienungsanleitung
Table of Contents
Remote Control Guide
Thank you for choosing LEVOLOR®InMotion™ motorized
window coverings. This product has been custom built
for you from the highest quality materials. To avoid errors
and save valuable time, please read these instructions to
ensure you are properly programming your new remote.
Visit LEVOLOR.com/InMotionSupport for additional
information.
Product Overview
Cellular, Natural and Roman Shades.................1
Banded, Roller and Sheer Shades.................... 2
Wood Blinds ....................................................... 3
Positioning.......................................................... 4
Remote Control.................................................. 5
Battery Installation............................................ 6
Wall Holder ..........................................................7
Programming
Getting Started .................................................. 8
Favorite Position ................................................ 9
Operating Mode ................................................10
Motor Speed ..................................................... 11
Travel Limits ......................................................12
Add or Remove Additional Remote .................13
Operation
Operating Instructions .....................................14
Additional Information
Troubleshooting ...............................................15
Warranty ...........................................................15
Customer Service ............................................15
Specifications ...................................................16
Declarations ......................................................16
1
Remote Control Guide
Product Overview
Cellular, Natural and Roman Shades
Programming
Programming button, charging port and indicator
light are located in the shade’s right headrail end cap.
Programming button does not act as a manual control and
the shade will not move when the button is pressed.
During setup, the shade will confirm programming by
jogging, with a slight down and up movement.
Charging
Magnetic charging insert comes installed in shade. For easy
charging, attach the magnetic charging adapter to the
micro-USB charging cable and power adapter before
connecting to the headrail to charge. For standard
charging, remove the magnetic charging insert from
the headrail and use the micro-USB charging cable and
power adapter.
Indicator light will flash red when battery is low, flash green
during charging and remain green when fully charged.
NOTE: Before installation, fully charge shade.
Programming Button
Micro-USB Charging Port
Indicator Light
Magnetic Charging Standard Charging
Magnetic
Charging
Insert
Magnetic
Charging
Adapter
Micro-USB
Charging
Cable
Home .
2
Remote Control Guide
Product Overview
Banded, Roller and Sheer Shades
Programming
Programming button, charging port and indicator light
are located on the right-side of the shade headrail.
Programming button acts as a manual control and the
shade will move when the button is pressed.
During setup, the shade will confirm programming by
beeping and jogging, with a slight down and up movement.
Charging
Magnetic charging insert comes installed in shade. For easy
charging, attach the magnetic charging adapter to the
micro-USB charging cable and power adapter before
connecting to the headrail to charge. For standard
charging, remove the magnetic charging insert from
the headrail and use the micro-USB charging cable and
power adapter.
Indicator light will flash red when battery is low, flash green
during charging and remain green when fully charged.
Shade will also beep 10 times when in use to indicate a
low battery.
NOTE: Before installation, fully charge shade.
Programming Button
Micro-USB Charging Port
Indicator Light
Magnetic Charging Standard Charging
Magnetic
Charging Insert
MagneticChargingAdapter
Micro-USB
Charging Cable
Home .
3
Remote Control Guide
Product Overview
Wood Blinds
Programming
Programming button is located inside the headrail on the
left corner of the motor and a paperclip or similar tool
must be used to activate.
The programming button is not accessible when mounted.
Programming button acts as a manual control and the
blind will move when the button is activated.
During setup, the blind will confirm programming by
jogging, with a slight down and up movement.
Charging
The rechargeable battery mounts between the headrail and
valance. Indicator light and charging port are located on the
bottom of the battery. Magnetic charging insert comes installed
in battery. For easy charging, attach the magnetic charging
adapter to the micro-USB charging cable and power adapter
before connecting to the battery to charge. For standard
charging, remove the magnetic charging insert from the battery
and use the micro-USB charging cable and power adapter.
Indicator light turns red when battery is low. During charging,
the light will turn green when fully charged.
NOTE: Before installation, fully charge battery.
Magnetic Charging
Valance omitted for clarityValance omitted for clarity
Standard Charging
Magnetic
Charging
Insert
Magnetic
ChargingAdapter Micro-USB
Charging Cable
Indicator
Light Indicator
Light
Home .
4
Remote Control Guide
Product Overview
Positioning
Each blind or shade comes with predefined position limits
that can be adjusted as needed.
Upper Limit
This is the highest position available which provides the
best view and protects product from damage.
Lower Limit
This is the lowest position available which fully covers the
window and matches the length requested at time of order.
Favorite Position
This is the preset position that is saved on the blind or shade
and is set to the most popular position based on product
category. Send to Favorite Position by holding the stop
button.
Product Default Favorite Position
Banded Shades Fully lowered,bands open
Cellular Shades : Bottom Up 50% lowered
Natural Shades 50% lowered
Roller Shades 50% lowered
Roman Shades 50% lowered
Sheer Shades Fully lowered,vanes closed
Wood Blinds Slats open 90 degrees
Upper limit Lower Limit Favorite
Home .
5
Remote Control Guide
Remote Overview
Remote Control
The LEVOLOR InMotion remote has 15 available channels
and each channel can control up to 20 shades at once.
This remote is designed to control bottom-up shades and
tilt-only wood blinds.
LCD Display
Up
Stop
(Hold to send to
favorite position)
Down
Higher
Channel
Lower
Channel
(0 controls
all channels)
P2
2AAABatteries
(included)
Screw
(Install after programming)
Switch
P2
Front View
Back View
Home .
6
Remote Control Guide
Remote Overview
Battery Installation
Gently press down on cover and slide to remove.
Install 2 AAA batteries (included). Align batteries as
shown below.
Program your remote, replace the back cover and
install closure screw.
1
1
2
2
3
3
Install (2)AAA
Batteries
As Shown
Install Screw
Remove
Back
Cover
Replace
Back
Cover
Home .
7
Remote Control Guide
Remote Overview
Wall Holder
Provide a home for LEVOLOR remotes with the
remote holder.
Tools Needed to Mount Remote Holder
•Power drill
•3⁄32” drill bit
•Phillips screwdriver
•Pencil
Remote Holder Mounting Instructions
Choose location and mark wall plate placement.
If you are mounting onto wood, use a 3⁄32” drill bit
to drill pilot hole. If you are mounting onto drywall,
use the included drywall anchor.
Attach the wall plate to the wall using the screw
provided; ensure the curved edge is on top.
Slide mounting disc over wall plate and snap
into place.
Place remote on mounting disc and gently slide
downward to seat remote onto holder.
Slide remote upward to remove from holder.
1
2
3
4
5
6
Wall Plate
(Install Curved
Edge toTop)
Mounting
Surface
Mounting
Disc
Home .
8
Remote Control Guide
Programming
Getting Started
During programming, all blinds and shades will jog by
moving slightly down and up. Banded, roller and sheer
shades will both jog and provide an audible beep.
Certain programming functions will affect all blinds
and shades on the selected channel such as – favorite
position, travel limits, operating mode and motor speed.
To program an individual blind or shade: pair to its own
channel or put all other shades into sleep mode, or
disconnect blinds from their batteries. Put shades to
sleep by pressing the programming button for 6 seconds
until the motor jogs x 2. Wake shades by pressing the
programming button for less than 1 second.
Select a Channel
Use channel 0 to control all channels together.
Press the
-
button on the remote to select a lower
channel.
Press the +button on the remote to select a higher
channel.
Hide Unused Channels
Select a channel other than 0, then press and hold
the
-
and +buttons simultaneously until remote
control displays “C” then “15”, then release buttons.
Press the
-
or +buttons until the number of visible
channels needed is shown (between 1 and 15).
Press the stop button to confirm selection. The
screen will display “o” once to confirm selection.
NOTE: Repeat steps 1-3 to unhide channels.
1
1
2
2
3
Home .
Andere Handbücher für InMotion
3
Inhaltsverzeichnis
Sprachen:
Andere Levolor Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
