Lexmark X502N Bedienungs- und Sicherheitshinweise

Seite 1 von 4 www.procompsys.de

Manual to replace the CPU-fanof the Lexmark x502n

Attention: This manualrefers exclusively to the altered fandistributed by

ProCompSys! Standard-models of this fan can not be operated withthe Lexmark

x502n in this manner!

Note: Arbitrary modification on your device may void the manufacturer's

warranty! In either case disconnect the device from power before opening!

Voltage can remaininelectronic components of a device, even if power is

disconnected. If needed, consult an expert.

Turn device off

and remove any

cables from the rear side.

Remove the screw fixing the side

panel

from the rear side.

Remove the side

panelbysliding it

to the rear side of thedevice.

Remove the screw fixing the inner metal

side-panel.

Seite 2 von 4 www.procompsys.de

Remove the metal-side-panel by

sliding it to the rear side of the

device.

Remove the defective fan's plug

from the jack on the circuit board.

The fan is fixed with 4 screws.

First, remove the

upper

right

and

lower-left screws of the fan. The fan

can alreadybe fullyremoved at this

point.

Two spacers remain attached to the

circuit board. Unscrew the two other

spacers from the defective fanand

attach them to the new fan, just as

diagonally arranged.

Attach the new fan back to the two

spacers that remained on the

circuit boardusing the two

remainingscrews.

Due to variation inproduction on behalf

of Lexmark, it is not possible to equip

the replacement-fan witha plug fitting

all lots of this printer model. In particular

cases it might be necessary to make

some little adjustments.

Given the case that plug and jack do not

fit without further ado, you have to...

(continued on next page)

Seite 3 von 4 www.procompsys.de

either a

) cut off the existing plug

from the defective fanand connect/

solder it to the replacement-fan

(pay attention to the polarity:

rednew àblackold,

blacknew àyellowold,

yellownew àredold!)

or b) file offthe replacement-fans's

pluguntilit fits into the jack

oder c) which appears to be the

most feasible solution remove the

plastc jack from the printer's circuit

board, so the plug's dimensions

don't interfere with the jack's

housing anymore.

If a modification is necessary in

your case, solution No. c) is

depicted below.

If plug and jack do fit without

further ado in your case, you

can skip the following instruct-

tions of this manual, that are

highlighted on a yellow back-

ground.

The white plastic jack is glued to the

circuit boardand can be loosened quite

easily usingp. ex.a pairof long-nosed

pliers.

As soon as the glued connection is

loosened, pull off the white jack-housing

straightforward from the three pin

contacts using slightly circular

movement.

Pay extreme attention to having

powered off the printer and avoid

contact of the used tool with the

circuit board's components!

Seite 4 von 4 www.procompsys.de

10.

The replacement

fan's plugcan

now easily be connected to the

contact pins on the circuitboard.

Pay attention to the correct polarity

(red wire to the left)!

("Red wire to the left " also

applies if you did not have to

remove the white plastic jack

from the circuit-board!)

The color-sequence of the

cables of the replacement-fan

does not necessarily have to

coincide with the color-

sequence of the cables of the

defective original fan!

11.

Tentatively connect the printer to

power and switch it on, to check

the new fan's function.

The display-message 'Warning:

CPU Fan is Locked' should be gone

now.

If necessary, check the plug's snug

fit.

12.

attach t

he side

panels according to

steps 5, 4, 3 and 2.

Andere Handbücher für X502N

Andere Lexmark Multifunktionsdrucker Handbücher

Lexmark

Lexmark C736 Series Bedienungsanleitung

Lexmark

Lexmark X782 Bedienungsanleitung

Lexmark

Lexmark X792 Technisches Handbuch

Lexmark

Lexmark Platinum Pro905 Bedienungsanleitung

Lexmark

Lexmark X950de Installationsanleitung

Lexmark

Lexmark 21Z0341 Bedienungsanleitung

Lexmark

Lexmark X544DN Bedienungsanleitung

Lexmark

Lexmark 7100 series Bedienungsanleitung

Lexmark

Lexmark X364dw Bedienungsanleitung

Lexmark

Lexmark X73 Series Bedienungsanleitung

Lexmark

Lexmark MX826 Bedienungsanleitung

Lexmark

Lexmark 2470 - X Color Inkjet Bedienungsanleitung

Lexmark

Lexmark 8300 Series Bedienungsanleitung

Lexmark

Lexmark X664e MFP Handbuch

Lexmark

Lexmark XM7200 Series Bedienungsanleitung

Lexmark

Lexmark X658DFE Bedienungsanleitung

Lexmark

Lexmark 3048476 Bedienungsanleitung

Lexmark

Lexmark X7675 Bedienungsanleitung

Lexmark

Lexmark 20D0001 Bedienungsanleitung

Lexmark

Lexmark MS810 Series Bedienungsanleitung

Lexmark

Lexmark C792e Bedienungsanleitung

Lexmark

Lexmark X5100 Series Bedienungsanleitung

Lexmark

Lexmark MX610 Series Bedienungsanleitung

Lexmark

Lexmark X850e Technisches Handbuch

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Brother

Brother MFC-9760 Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung

Oce

Oce VarioLink 5022 Bedienungsanleitung

Copystar

Copystar CS 4551ci Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 4650EN Bedienungsanleitung

Brother

Brother MFC-9840CDW Bedienungsanleitung