Lexmark MS710 Series Kurzanleitung
Media Guide
The printer supports the following paper and specialty media sizes. Select custom sizes up to the maximum measurements
specified for the Universal setting.
Paper sizes supported by the printer
Paper size1Dimensions Standard or
optional 250‑or
550‑sheet trays
Optional
2100‑sheet tray
Multipurpose
feeder
Duplex
A4 210 x 297 mm
(8.3 x 11.7 in.)
A5 148 x 210 mm
(5.8 x 8.3 in.)
A6 105 x 148 mm
(4.1 x 5.8 in.)
X
JIS B5 182 x 257 mm
(7.2 x 10.1 in.)
X
Letter 216 x 279 mm
(8.5 x 11 in.)
Legal 216 x 356 mm
(8.5 x 14 in.)
Executive 184 x 267 mm
(7.3 x 10.5 in.)
X
Oficio 216 x 340 mm
(8.5 x 13.4 in.)
Folio 216 x 330 mm
(8.5 x 13 in.)
Statement 140 x 216 mm
(5.5 x 8.5 in.)
X
Universal2105 x 148 mm to 216
x 356 mm (4.13 x
5.83 in. to 8.5 x 14 in.)
X
70 x 127 mm to
216 x 356 mm
(2.76 x 5 to 8.5 x 14 in.)
XX X
1If your preferred default paper size cannot be set in the printer control panel, then you may select common paper sizes that
correspond to the position of the length guide in the tray from the Paper Size/Type menu. If the paper size is not available, then select
Universal or turn off tray size sensing. For more information, contact customer support.
2To support two‑sided (duplex) printing, the Universal width must be between 105 mm (4.13 inches) and 216 mm (8.5 inches); the
Universal length must be between 148 mm (5.83 inches) and 356 mm (14 inches).
Media Guide
Page 1 of 4
Storing paper
Use these paper storage guidelines to help avoid jams and uneven print quality:
•For best results, store paper where the temperature is 21°C (70°F) and the relative humidity is 40 percent. Most label
manufacturers recommend printing in a temperature range of 18–24°C (65–75°F) with relative humidity between 40 and 60
percent.
•Store paper in cartons, on a pallet or shelf, rather than on the floor.
•Store individual packages on a flat surface.
•Do not store anything on top of individual paper packages.
•Take paper out of the carton or wrapper only when you are ready to load it in the printer. The carton and wrapper help keep
the paper clean, dry, and flat.
Avoiding jams
Load paper properly
•Make sure paper lies flat in the tray.
Correct loading of paper Incorrect loading of paper
•Do not remove a tray while the printer is printing.
•Do not load a tray while the printer is printing. Load it before printing, or wait for a prompt to load it.
•Do not load too much paper. Make sure the stack height is below the maximum paper fill indicator.
Media Guide
Page 2 of 4
•Do not slide the paper into the tray. Load paper as shown in the illustration.
•Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing tightly against the
paper.
•Push the tray firmly into the printer after loading paper.
•If you are loading prepunched paper for use with the staple finisher, then make sure the holes on the long edge of the paper
are on the right side of the tray. For more information, see the “Loading paper and specialty media” section of the User’s Guide.
Allow the paper to enter the optional mailbox bins properly
•When using A4‑, folio‑, or legal‑size paper, make sure to adjust the bin extender fully so that the paper enters the bin properly.
Notes:
–If the bin extender is shorter than the size of the paper you are printing on, then the paper causes a jam in the
mailbox bin. For example, if you are printing on a legal-size paper and the bin extender is set to letter-size, then a jam
occurs.
–If the bin extender is longer than the size of the paper you are printing on, then the edges become uneven and the
paper is not stacked properly. For example, if you are printing on a letter-size paper and the bin extender is set to
legal-size, then the paper does not stack properly.
Media Guide
Page 3 of 4
•If paper needs to be returned to the mailbox bin, then insert the paper under the bin arm, and then push the paper all the
way back.
1
2
Note: If the paper is not under the bin arm, then a jam occurs due to an overfilled bin.
Use recommended paper
•Use only recommended paper or specialty media.
•Do not load wrinkled, creased, damp, bent, or curled paper.
•Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on
a level surface.
•Do not use paper that has been cut or trimmed by hand.
•Do not mix paper sizes, weights, or types in the same tray.
•Make sure the paper size and type are set correctly on the computer or printer control panel.
•Store paper according to manufacturer recommendations.
Media Guide
Page 4 of 4
Andere Handbücher für MS710 Series
10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Lexmark Drucker Handbücher
Lexmark
Lexmark M1145 Montage- und Wartungsanleitung
Lexmark
Lexmark CS310 Series Bedienungsanleitung
Lexmark
Lexmark W840 Bedienungsanleitung
Lexmark
Lexmark 12N0008 - C 910 Color LED Printer Betriebsanleitung
Lexmark
Lexmark E360dn Series Bedienungsanleitung
Lexmark
Lexmark E350d Bedienungsanleitung
Lexmark
Lexmark Multifunction Laser Montage- und Wartungsanleitung
Lexmark
Lexmark E360D series Bedienungsanleitung
Lexmark
Lexmark C910 Finisher Produktinformationsblatt
Lexmark
Lexmark 22Z0000 Bedienungsanleitung
Lexmark
Lexmark C520n Bedienungsanleitung
Lexmark
Lexmark MS911 Bedienungsanleitung
Lexmark
Lexmark Color Jetprinter Z43 Leitfaden
Lexmark
Lexmark MX6500e 6500e Service-Handbuch
Lexmark
Lexmark 30G0310 - T 654n B/W Laser Printer Betriebsanleitung
Lexmark
Lexmark Color Laser Bedienungsanleitung
Lexmark
Lexmark B3340dw Bedienungsanleitung
Lexmark
Lexmark C 750 Bedienungsanleitung
Lexmark
Lexmark 5700 - Color Jetprinter Technisches Datenblatt
Lexmark
Lexmark 250d - E B/W Laser Printer Bedienungsanleitung
