LG DM110 Bedienungsanleitung

User Guide

FCC WARNING STATEMENT

For body-worn operation, the antenna should be kept at least 1 inch from the body

when transmitting, to comply with FCC RF exposure requirements. An optional

holster/belt-clip is available as an accessory. Users are cautioned that the use of

non-tested accessories may exceed FCC RF exposure limits. Please contact your

local dealer for optional accessory information.

CHAPTER 1. THE NAME AND FUNCTIONS

Hold Icon

Signal Strength (RSSI)

In Use

No Service

Digital Service is available

Roaming

Short Message (Voice)

Battery Level

Short Message (Text)

Vibrator Enabled

CHAPTER 2. BASIC FUNCTIONS

Turning the Phone On and Off

1. Connect the terminal to the charged battery or the external power supply.

2. Press the [END/PWR] key for about 1.5 seconds until a red right appears on the upper side

of the terminal.

< Turning the Terminal Off >

1. Press the [END/PWR] key until the end message appears on the LCD, and then stop pressing

the key.

2. If an antenna is stretched, push it in for safety.

Making a Call

<Method1> Entering the Entire Phone Number

1. If the terminal is turned off, turn it on.

2. Enter the phone number.

(Enter the area code, if necessary.)

3. Press the [SND] key.

-If the terminal is locked on, enter the password to unlock the terminal. Then, attempt the

call again.

-If the call is not connected, “Call Failed”signal will be indicated on the LCD.

4. Press the [END] key.

<Method2> Using Phone Book Entry

1. Enter the phone entry number, and press the [SND] key or press the related phone entry

number for some time. Then, the call will be attempted.

e.g.) Press the [2] key for some time, then call will be

connected to the phone number stored in the Entry #2.

2. If you are not sure of the phone entry number, select the Soft Key (BOOK) on the right side.

3. Place the cursor on the Phone Book, and press the Soft Key (SEL) on the left side.

4. Search the Phone Book Entry number or name requested in the Phone Book to attempt a call

to the phone number stored in it.

<Method3> Using the Recent Call History

1. Select the Soft Key (BOOK) on the right side.

2. If the screen changes, place the cursor on the Call History. Then, press the Soft Key (SEL) on

the left side.

3. If the “Outgoing Calls”, “Incoming Calls”, and “Missed Calls”are indicated on the screen,

select the menu requested. Ten phone numbers of the recent calls are stored in each menu.

Place the cursor on the menu requested, and press the Soft Key (SEL) on the left side.

4. The phone number list appears on the screen. Then, search and place the cursor on the phone

number or name requested, and press the [SND] key.

Correcting Dialing Mistakes

1. Press the Soft Key [CLR] on the right side of the screen to erase the number or character of

the last entry.

2. Press the Soft Key (CLR) on the right side for one second, then all the number or character

requested will be erased.

Receiving Calls

1. Press any key except for the [END/PWR] key to receive a call.

HPress the END Key once to stop the bell or vibration.

HH Press the END Key twice to end the incoming call

2. When the call completes, press the [END/PWR] key.

3. Or close the flip.

Mute

1. Press the Soft Key (MENU) on the left side during the call.

Redialing Last Outgoing Number

1. Just press [SND] key to redial the last outgoing number. Then, the call will be attempted.

<Method 2> using the Call History

1. Press the Soft Key (BOOK) on the right side.

2. Place the cursor on the Call history menu on the screen, and press the Soft Key (SEL) on

the left side.

3. Then, three menus will appear.

“Outgoing Calls”:Ten last outgoing calls are stored in this menu.

“Incoming Calls”:Ten last incoming calls are stored in this menu

“Missed Calls”:Ten last missed calls are stored in this menu

2. If a popup menu appears on the screen,

place the cursor on the Mute menu and

press the Soft Key (SEL) on the left side to

select the Mute state. (The message”Mute”

will be indicated on the screen.)

3. Press the Soft Key (OPT) on the left side

to clear the function. The popup menu will

appear. Select the Unmute menu.(The

message“Mute”willbedisappearonthescreen

4. Place the cursor on the menu requested, and press the Soft Key (SEL) on the left side.

e.g.) Place the cursor on the “Outgoing Calls”menu and press the Soft

Key (SEL) on the left side.

5. The phone number list will appear. Place the cursor on the phone number or name requested,

and press the [SND] key. Then, the call will be attempted.

Adjusting the Volume

It is possible to adjust the speaker volume, ring volume, and the ringer type with the volume

buttons on the upper left side of the terminal.

-It is possible to adjust the speaker volume during the call.

-It is possible to adjust the key tone volume in a idle state.

-It is possible to adjust the ring volume during the ringing time.

-It is possible to adjust the ring volume from the Sounds item on the Menu screen also.

( F[MENU] [Sounds][SpkVol] or [MENU]-1-2)

If you turn the ring volume down to the minimum, the message “-Ringer Off-“will be indicated

on the LCD and no ringing sound will be sent out.

-Adjust the ringer type on the Sounds item on the Menu screen.

(F[MENU] [Sounds][Tone Length] or [MENU]-1-5)

CHAPTER 3. PHONE BOOK FEATURES

Two types of Phone Books

This service enables easier use of the outgoing or incoming phone numbers because it is

possible to store up to 200 phone numbers in the memory. It is possible to store the phone

numbers either in the Personal Phone Book memory or in the Recent Call History List

Personal Phone Book Memory

It is possible to store up to 4 phone numbers of 32 digits including name up to 12 characters in

each entry of the Phone Book.

1. Enter the number to be stored. (Up to 32 characters)

2. Press the Soft Key (OPT) on the left side and then, a popup

menu will appear. Place the cursor on the [save] key on the

Menu and press the Soft Key (SEL) on the left side.

3. Select a Label.

4. Enter the name up to 12 characters.

(Verify the number of characters and

press the [save] key.) If you do not

want to enter the name,press the

[save] key without entering characters.

5. Designate the Entry number. Then, an empty Entry number will be

designated automatically. If you do not want this Entry number,

designate another Entry number. If an existing phone number

occupies the memory of the designated Entry number, a message

will appear to verify if you want to overlap the existing one with

a new one. If you select the [ok] key, the existing phone number

will be erased in the entry, and a new one will be stored. If you

want to maintain the existing phone number, designate another

entry number.

6. Messages will appear to set the Voice Dial, ID Ringer, screen color, and the Secret function

in turn. If you set the Secret function to the memory address, you will be unable to see the

phone number or to correct it.

Entering Characters

You will be provided with 5types of modes (English Lower, English Upper, Digil, Special Char,

Icon) to enter the characters. Use the upside (é) key to change among the modes while entering

the characters. The present mode is indicated on the lower center of the screen. Whenever you

press the upside (é) key, the modes will change in the order of “ENG”- “eng”- “DIG”-

“SPEC”- “ICON”- “ENG”`````` . Select the mode before you enter the characters, and enter

the characters.

1. When the mode is ready for entry, the cursor (“_“)will be

indicated on the space for entry.

(If you enter one character, the cursor will move to the following

space automatically and wait for entry.)

2. Use the right side (è) key or the “0”key in the “ENG”- “eng”state to place a space among

the characters.

3. Verify if the cursor is placed where the character is to be entered, and change the mode by

using the upside/downside (t/ s) key.

4. Verify if the mode requested is indicated on the lower center of the screen, and enter the

character.

5. Use 8 keys of [2]~[9] to enter the character in the “eng”and

“ENG”mode. One key is designated with three or more than

three characters. Therefore, press each key repeatedly for a short

period of time until the character requested appears. For example,

if you want to enter a character “K”,set the “ENG”mode with

the upside/downside (s/ t) keys and then press [5] key twice for short time continuously.

6. Enter the numbers of 0~9 with ten keys from [0] to [9] in a “DIG”mode.

(Reference: The “ENG”, “eng”and “DIG”modes remain in the same state even after you

enter a character, while the “SPEC”and “ICON”modes automatically change into an

“ENG”mode after you enter one character.)

7. Enter a special code or icon in the “SPEC”or “ICON”mode.

An icon set is indicated in the order of 12 keypads on the right

side of the screen in a “SPEC (ICON)”mode. Press the key

corresponding to the symbol (icon) to be entered in reference of

them, and then the symbol (icon) will be entered on the space

where the cursor is placed. Press the Soft Key (MORE) on the

right side when the symbol (icon) set is indicated on the screen,

and then another set of symbols (icons) will be indicated on the

screen. The symbol (icon) set is composed of three types of sets.

Press the Soft Key (MORE) on the right side repeatedly in a

preset SPEC (ICON) mode to change one type of symbol set

into another one. If the symbol (icon) set requested is indicated, use the keypad to enter the

symbol (icon).

8. Use the Soft Key (CLR) on the right side to erase the input character. Press it for a short

period of time to erase the last input character, and press it for some time to erase all the

input characters.

9. If you complete entry of the characters, use the Soft Key on the left side to move to other

items.

Recent Call History List

This service enables easy and fast redialing with its function to store ten last outgoing calls,

incoming calls, missed calls and added phone numbers (numbers stored by the scratch pad

function).

1. Press the Soft Key (BOOK) on the right side of the screen.

2. Place the cursor on the Call history of the screen, and press the Soft Key (SEL) key on the

left side.

3. Then, three menus will appear on the screen.

-“Outgoing Calls”:Ten last outgoing calls are stored in

this service.

-“Incoming Calls”:Ten last incoming calls are stored in

it.

-“Missed Calls”:Ten last missed calls are stored in it.

Select one of the three menus.

4. Then the corresponding phone number list will appear. Place the cursor on the number

requested and press the [SND] key to attempt a call.

Retrieving Numbers

Inhaltsverzeichnis

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung

Blackbe;rry

Blackbe;rry CURVE 8300 - SMARTPHONE Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 - VERSION 4.1 Bedienungsanleitung