LG KP220 - Cell Phone 60 MB Bedienungsanleitung

Date: March, 2008 / Issue 1.0

Service Manual Model : KP220

Service Manual

KP220

Internal Use Only

AMENDMENT RECORD

AMENDMENT RECORD SHEET

Issue Number Date

Draft 1.00 29.11.2007

Draft 1.2 14.02.2008

Draft 1.3 18.02.2008

For details of previous history refer to archival documents.

New Issue Number – Date Changes This Issue, Page and Description Remarks

Draft 1.00 29.11.2007 All for Publication First draft

Issue

Draft 1.2 14.02.2008 All for Publication Second

draft Issue

Draft 1.3 18.02.2008 All for Publication Third draft

Issue

KP220 SERVICE MANUAL V1.2

Next Section >>

Main Menu

SECTION 1

Introduction

KP220 SERVICE MANUAL V1.2

1. Introduction

The variation of “KP220” is shown below.

This Service Manual is indicated for 7338.

Variation Note.

Product Code Trade Name

7338 XXXXXXXX KP220

KP220 SERVICE MANUAL V1.2

This is the Electronic Service Manual for KP220 Triple Band GSM Digital

Cellular Telephone from LG. It contains specific information on repair and test

procedures.

For details of user functions, general operation and installation, please refer to the

User Guide.

The Service Manual is set out in the following sections.

1. Precautions for Repair Work : provides general guidelines for

undertaking safe and efficient repair work.

2. Unit Specification: provides the technical specifications for

KG195 Triple Band GSM Digital Cellular Telephone.

3. Introduction of Service Level :

Service Level 1:describes definition of Service Level 1, equipment and

tools required for this level.

Service Level 2 :describes definition, equipment and tools required for

Service Level 2.

4. Circuit Description: provides functional details of the circuits, block

diagrams and component purpose descriptions.

Servicing : defines the jigs, fixtures and test configurations required for

servicing the product; and describes the processes of assembly and

disassembly.

Troubleshooting : provides an aid to fault finding the product. Includes,

using the signal levels and plots at various parts of the circuit.

7. Device Information : provides functional information and pin-outs of

most of the semiconductor devices within the HHP.

8. Glossary : terms used in this GSM and this manual.

KP220 SERVICE MANUAL V1.2

Next Section >>

Main Menu

SECTION 2

Precautions

for Repair Work

KP220 SERVICE MANUAL V1.2

PRECAUTION

Important

Please read the following cautions, notes and

warnings before progressing through this manual or

undertaking any repair action.

Remember: SAFETY FIRST!

CAUTION:

AC Power Cord:

Care must be taken not to damage the AC power cord as fire or electric shock may

result.

Battery Pack:

Only use the specified batteries and chargers with this equipment.

Do not short the battery terminals together.

Keep the battery pack away from fire and sources of ignition.

Remember to recharge the battery pack after each use.

Before Powering up the Equipment:

•Only switch on the telephone’s power once the test or installation set-up is

complete.

•Switching on at the wrong time may result in electric shock or damage to system

components.

•Always ensure that the power is switched off before making connections /

disconnection’s.

•It is important to check that the correct DC voltage is applied to the equipment to

prevent electrical damage.

Component Polarity:

Always check the polarity of connections and components before soldering.

Particular attention must be paid to IC.s, diodes, transistors, capacitors and any

other semiconductor device that is polarity dependent.

KP220 SERVICE MANUAL V1.2

Electrostatic Damage (ESD):

Semiconductor devices are easily damaged by electrostatic discharge. Many of the

procedures detailed in this manual involve disassembly of the equipment and

therefore handling of the printed circuit boards.

To protect these devices from ESD a wrist strap connected to ground must be worn.

In addition to this the work surface must be covered with an anti-electrostatic mat,

which should also be grounded.

If printed circuit boards are to be stored without being re-assembled into their

equipment, then they must be kept in an anti-electrostatic bag.

Grounding:

Each piece of test equipment should be electrically grounded. A third (grounding)

pin is provided as a safety feature. Ensure that the electrical outlet also contains

this feature.

Cosmetic Protection during Repair Work:

Always ensure that the working surface is kept clean and free from abrasive

materials.

The LCD is very susceptible to scratches and damage. It should be covered with

clear adhesive vinyl while the equipment is disassembled.

Storage of Faulty Components:

Any components that are replaced due to failure should be kept safely in an anti-

electrostatic container. NEC’s Quality or Research & Development Departments

may require them to make quality and reliability investigations.

No Fault Found Equipment:

In some cases the reported symptom may not be apparent. You may subject the

equipment to a controlled amount of stress, vibration and temperature variation to

see if the fault occurs.

Care should be taken not to apply excessive stress or vibration or extreme

temperature variations as further faults may develop.

KP220 SERVICE MANUAL V1.2

Soldering and Disordering :

The solder used is only Pb-free.

Fast, accurate and high quality soldering is required to minimize the risk of heat

damage to the electronic components.

It is necessary to adjust the temperature of soldering tip to 330 degrees or less.

The soldering tip should not be in contact with components or PCB tracks for longer

than 4 seconds (average). This time depends on temperature conditions of parts.

Heat the pad on the PCB and the lead, quickly apply solder, remove heat and cool.

After soldering is complete, ensure that all solder joints are of good quality - no dry

joints, solder bridges, cracks or excess solder.

The majority of chip components are machine mounted using solder paste.

Removal of the solder is not sufficient for chip component removal. Each solder

point must be heated simultaneously and quickly (to prevent component and PCB

damage). When the solder has melted, remove the component with tweezers.

Short Circuits:

Care must be taken to avoid short circuits. Soldering, solder dust, screws, metal

clippings, metal wrist watches etc. can cause short circuits on PCBs which may

result in component damage.

Test Equipment Calibration:

Your test equipment should be calibrated before use. Frequent calibration is

essential to ensure high quality and reliable repairs.

Cleaning:

Before cleaning ensure that the telephone is switched off and disconnected from the

power source. Cleaning should be done using a soft dry cloth. If the equipment is

heavily soiled a soft cloth soaked in a mild synthetic detergent diluted in water may

be used.

Never use benzene or any other chemicals to clean the equipment.

RF Shielding:

It is advisable to carry out detailed measurements and repair (in particular RX) in a

shielded area to minimize RF interference.

AC Adapter and Battery Charger:

The AC adapter and battery chargers are for indoor use only. Ensure that the

devices are not exposed to rain or moisture

KP220 SERVICE MANUAL V1.2

Electrical Safety:

Electrical equipment is hazardous if misused. Any repairs must be carried out with

care and only by authorized personnel.

Ensure all power sources are switched off and power cords removed before

undertaking any repairs.

Hazardous Waste:

The battery pack, if incorrectly disposed of, is an environmental hazard. It must be

disposed of in accordance with the regulations of the country concerned.

Never dispose of the battery pack in fire or water.

Confidentiality:

The circuitry within this equipment contains several components that are regarded

as company confidential. Only use NEC specified parts as replacements.

RF Injury:

To avoid RF injury, direct exposure to radio frequency energy should be avoided. In

particular, exposed parts of your body (especially the eyes and face) should not

come into contact with the antenna while the equipment is transmitting.

Storage Conditions:

It is recommended that the following storage conditions should be avoided to

prevent damage to the equipment: -

Dusty.

Humid.

Near to magnetic equipment

In direct sunlight

Ventilation:

Repair areas should be well ventilated and fume extraction systems should be

installed where necessary. Potential hazardous substances are solder fumes, flux,

alcohol etc.

PCB Handling:

It is recommend that cotton gloves are worn during repair work. This is to protect

your hands from chemical contamination and to protect the PCBs from fingerprints

and humidity

Andere Handbücher für KP220 - Cell Phone 60 MB

Inhaltsverzeichnis

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung

Blackbe;rry

Blackbe;rry CURVE 8300 - SMARTPHONE Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 - VERSION 4.1 Bedienungsanleitung