LG HB9522A Bedienungsanleitung
Built-In Gas Cooktops
Installation and Operating Instructions
HB9522A
To avoid the risk of accidents or damage to the Gas Cooktops,
it is essential to read these operating instructions
before it is installed or used for the first time.
And please keep this manual for later reference.
P/No.: MFL62060301
http://au.lge.com (Australia)
http://nz.lge.com (New Zealand)
Contents
Introduction ................................................................................. 3
1. Instructions for safe and proper use.........................................3
Instructions for the installer ...................................................... 5
2. Positioning of the hob...............................................................5
3. Electrical connection ................................................................9
4. Gas connection ......................................................................10
5. Adaptation to different types of gas........................................12
6. Final operations......................................................................16
Instructions for the user .......................................................... 19
7. Using the hob .........................................................................19
8. Cleaning and maintenance ....................................................21
These instructions are valid only for end user countries whose
identification symbol appear on the cover of this manual.
INSTRUCTIONS FOR THE INSTALLER: these are for the
authorised person who must carry out a suitable check of the gas
system, install the appliance, set it functioning and carry out an
inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice,
description of the commands and the correct procedures for
cleaning and maintenance of the appliance.
2
1. Instructions for safe and proper use
This manual is an integral part of the appliance and therefore must
be kept in its entirety and in an accessible place for the whole
working life of the cooking Hob. We advise reading this manual and
all the instructions therein before using the cooking Hob. Also keep
the series of nozzles supplied. Installation must be carried out by
qualified personnel in accordance with the regulations in force. This
appliance is intended for domestic uses and conforms to current
regulations in force. The appliance has been built to carry out the
following functions: Cooking and heating-up of food. All other
uses are considered improper.
The manufacturer declines all responsibility for improper use.
Do not leave the packing in the home environment. Separate the
various waste materials and take them to the nearest special
garbage collection centre.
It is obligatory for the electrical system to be grounded according to
the methods required by safety rules.
The plug to be connected to the power cable and the socket must
be the same type and must conform to current regulations.
Never unplug by pulling on the cable.
Immediately after installation carry out a brief inspection test of
the cooking Hob, following the instructions below. Should the
appliance not function, disconnect it from the supply and call the
nearest technical assistance centre.
Never attempt to repair the appliance.
Always check that the control knobs are in the position
“ZERO”(OFF) when you finish using the hob.
3
Introduction
Introduction
The identification plate, with technical data, serial number and
marking is clearly visible under the casing.
The plate on the casing must not be removed.
Before connecting the device, make sure that it has been regulated
for the type of gas that will feed it, checking the label under the Hob.
Do not put pans without perfectly smooth and flat bottoms on the
cooking hob grids.
Do not use pans or griddle plates that extend beyond the external
perimeter of the hob.
The hob is to be used by adults only. Do not let unsupervised
children play with the hob.
This appliance is designed for cooking food and it shall not be used
as a space heater.
Do not spray aerosols in the vicinity of this appliance while it is in
operation.
WHERE THIS APPLIANCE IS INSTALLED IN MARINE
CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A
SPACE HEATER.
The manufacturer declines all responsibility for damage to
persons or things caused by non-observance of the above
prescriptions or by interference with any part of the appliance or
by the use of non-original spares.
DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
DO NOT MODIFY THIS APPLIANCE
4
2. Positioning of the hob
This appliance shall be installed only by authorized persons in
accordance with AS5601 - Gas Installations, any statutory regulations,
local gas regulations, municipal building codes, electrical wiring
regulations, and the manufacturer's installation instructions.
Clearance around the appliance must comply with the requirements of
AS5601.
The following operation requires building and/or carpentry work so
must be carried out by a competent tradesman. Installation can be
carried out on various materials such as masonry, metal, solid wood or
plastic laminated wood as long as they are heat resistant (T 90°C).
2.1 Attachment to support structure
Create an opening with the dimensions shown in the figure in the top
surface of the counter, keeping a minimum distance of 50 mm from the
rear border.
This appliance is classified as “type Y” in relation to fire hazards and
can therefore be mounted against walls higher than the work surface on
condition that a certain distance “X” be kept between the appliance and
the wall as shown in the figure so as to avoid damage from overheating.
Make sure there is a minimum of 750 mm between the hot plate flames
and any shelf that may be installed directly above them.
Carefully position the insulating seal supplied on the outer perimeter of
the hole made in the counter top as shown in figure 4 (the dimensions
in the figure refer from the hole to the inside of the seal), trying to
ensure that it sticks across the whole of its surface by applying light
pressure with your hands. Fix the hob to the unit using the appropriate
5
Instructions for the installer
6
Instructions for the installer
brackets Band spacers Aas shown in graphics 1, 2 and 3. Spacers A
will help to keep the hob top at the right distance from the edge of the
counter top to avoid future overheating during operation. Carefully trim
the surplus away from edge Cbeyond the seal (Fig.5).
7
Overall dimensions: location of gas and electrical connection
points (all measures in mm).
2.2 Clearance above and around domestic appliances
Extract from AS5601
REQUIREMENTS
1. Overhead clearances – (Measurement A)
Range hoods and exhaust fans shall be installed in accordance with
the manufacturer’s instructions. However, in no case shall the
60 cm 90 cm
hob hob
A 35 105
B65 50
C30 50
D85 75
*
Dimension A, C : Clearances are
these for the hose assembly.
Instructions for the installer
clearance between the highest part of the hob of the cooking
appliance and a range hood be less than 600 mm or, for an
overhead exhaust fan, 750 mm.
Any other downward facing combustible surface less than 600 mm
above the highest part of the hob shall be protected for the full width
and depth of the cooking surface area in accordance with Clause
5.12.1.2. However, in no case shall this clearance to any surface be
less than 450 mm.
2. Side clearances – (Measurements B& C)
Where B, measured from the periphery of the nearest burner to any
vertical combustible surface, is less than 200 mm, the surface shall
be protected in accordance with Clause 5.12.1.2 to a height C of not
less than 150 mm above the hob for the full dimension (width or
depth) of the cooking surface area. Where the cooking appliance is
fitted with a ‘splashback’, protection of the rear wall is not required.
3. Additional requirements for Freestanding and Elevated Cooking
Appliaces – (Measurements D& E)
Where D, the distance from the periphery of the nearest burner to a
horizontal combustible surface is less than 200 mm, then Eshall be
10 mm or more, or the horizontal surface shall be above the trivet.
See insets above.
NOTES
1. Requirement 3 does not apply to a freestanding or elevated cooking
appliance which is designed to prevent flames or the cooking
vessels from extending beyond the periphery of the appliance.
2. The ‘cooking surface area’ is defined as that part of the appliance
where cooking normally takes place and does not include those
parts of the appliance containing control knobs.
3. For definition of hob, see Clause 1.4.64.
4. For definition of trivet, see Clause 1.4.109.
5. Consideration is to be given to window treatments when located near
cooking appliances. See Clause 5.3.4.
8
3. Electrical connection
Make sure that the voltage and capacity of the power line conform
to the data shown on the plate located under the casing. Do not
remove this plate for any reason.
The plug on the end of the supply cable and the wall socket must
be the same type and conform to the current electrical system
regulations.
Check that the power line is adequately grounded.
On the power line, install an omnipolar cut-off device with contact
cut-off distance greater than or equal to 3 mm, located in an easily
accessible position near the unit.
Do not use reducers, adapters or shunts.
If the power cable is replaced, the wire section on the new cable
must not be less than 1 mm2(3 x 1 cable), keeping in mind that
the end to be connected to the hob must have the ground wire
(yellow-green) longer by at least 20 mm. Use only H05V2V2-F
cable or similar which has a maximum temperature of 90°C.
Any replacement needed should be carried out by a specialised
technician who should make the mains connections according
to the following diagram.
L= brown
N= blue
= yellow-green
The manufacturer will not be liable for any damage to persons
or property caused by non-observance of the above instructions
or deriving from the tampering of even a single part of the hob.
9
10
4. Gas connection
Use pipe-joint compound made for use with Natural U.L.P. gas.
The burner it controls is shown next to each knob (the
example corresponds to the front left burner).
This appliance is suitable for installation with Natural Gas
or ULPG (propane). Refer to page 12 for the relevant
burner pressure and appropriate injector sizes. When the
appliance is to be connected to Natural Gas then the
pressure regulator supplied must be fitted to the gas inlet.
A test point (for checking the gas pressure) is supplied
either with the regulator or as a separate fitting in the case
of ULPG (propane) appliances.
Connection of the appliance to the gas supply must be in accordance
with the requirements of AS5601. A 1/2” BSP connector at the inlet is
recommended and the gas supply line to the appliance must be of
adequate length to allow sufficient withdrawal of appliance for service
or disconnection and be:
1. annealed copper pipe or;
2. flexible hose according to AS/NZ1869 & be at least Class “B”,
10 mm diameter.
The appliance must be installed with provision to allow the gas to be
turned off and disconnected for servicing and removal of the appliance
as required from the gas supply.
Before the appliance is operated make certain all relevant parts are
placed in the correct position.
When the installation is completed the installation connections of
appliance will require to be leak tested, the burner operating pressure
and flame checked and adjusted.
Warranty service calls do not cover these adjustments!
To check the operating pressure of the appliance it is recommended at
least 2 large size burners are used. Ensure appliance is secured to wall
when installation is completed.
N.G. The regulator supplied must be fitted to the 1/2BSP thread at the
rear of the appliance. An approved manual shut-off valve must be
Instructions for the installer
Inhaltsverzeichnis
Andere LG Kochfeld Handbücher
LG
LG LCG3011 Series Bedienungsanleitung
LG
LG UPCE3064ST Bedienungsanleitung
LG
LG LCG3691ST - 36" Gas Cooktop Bedienungsanleitung
LG
LG LCE3081ST - 30in Smoothtop Electric Cooktop 5 Steady Heat... Schulungshandbuch
LG
LG LCG3091 Series Bedienungsanleitung
LG
LG LCE3010SBSP Bedienungsanleitung
LG
LG LSE4617 Series Bedienungsanleitung
LG
LG LCE3081ST - 30in Smoothtop Electric Cooktop 5 Steady Heat... Bedienungsanleitung
LG
LG CBGS3628 Series Bedienungsanleitung
LG
LG Studio LSCE305ST Bedienungsanleitung
LG
LG MFL62725501 Bedienungsanleitung
LG
LG Studio LSCE365ST Bedienungsanleitung
LG
LG LCG3611ST Bedienungsanleitung
LG
LG CBGJ3027 Series Bedienungsanleitung
LG
LG Studio LSCE305ST Bedienungsanleitung
LG
LG LCG3691ST - 36" Gas Cooktop Bedienungsanleitung
LG
LG Studio LSCE305ST Bedienungsanleitung
LG
LG HB6422A Bedienungsanleitung
LG
LG Studio LSCE365ST Bedienungsanleitung
LG
LG LSCG366ST/01 Bedienungsanleitung
