LG DLE0332W Bedienungsanleitung

Website:http://www.LGservice.com [For U.S.A]

www.lg.ca [For Canada]

ELECTRIC & GAS DRYER

SERVICE MANUAL

CAUTION

READ THIS MANUAL CAREFULLY TO DIAGNOSE

TROUBLES CORRECTLY BEFORE OFFERING SERVICE.

MODEL : DLE5911W

DLE2511W

DLE5932W

DLE5932S

DLE2532W

DLE0332W

DLG5911W

DLG2511W

DLG5932W

DLG5932S

DLG2532W

DLG0332W

MAR. 2003 PRINTED IN KOREA

P/No.:3828EL3001B

To avoid personal injury, disconnect power before servicing this product. If electrical power is required

for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks.

WARNING !

WHAT TO DO IF YOU SMELL GAS:

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by individuals possessing adequate backgrounds

of electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in

personal injury and property damage. The manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume any liability in connection with its use.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are

removed for service, they must be returned to their original position and properly fastened.

IMPORTANT

Electrostatic Discharge (ESD)

Sensitive Electronics

ESD problems are present everywhere. ESD may damage or weaken the electronic

control assembly. The new control assembly may appear to work well after repair is

finished, but failure may occur at a later date due to ESD stress.

Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted

metal in the appliance.

- OR -

Touch your finger repeatedly to a green ground connection point or unpainted metal

in the appliance.

Before removing the part from its package, touch the anti-static bag to a green ground connection

point or unpainted metal in the appliance.

Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.

When repackaging failed electronic control assembly in anti-static bag, observe above instructions.

Do not try to light a match, or cigarette, or turn on

any gas or electrical appliance.

Do not touch any electrical switches. Do not use any

phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions

carefully.

If you cannot reach your gas supplier, call the fire

department.

1. SPECIFICATIONS ..................................................................................................................4

2. FEATURES AND BENEFITS .................................................................................................... 5

3. INSTALLATION INSTRUCTIONS ........................................................................................... 6

4. COLUMBUS DRYER CYCLE PROCESS .................................................................................... 9

5. COMPONENT TESTING INFORMATION ..............................................................................10

6. MOTOR DIAGRAM AND SCHEMATIC..................................................................................13

7. CONTROL LAY - OUT .........................................................................................................14

8. WIRING DIAGRAM ............................................................................................................15

9. DIAGNOSTIC TEST .............................................................................................................16

9-1. TEST 1 120VAC ELECTRICAL SUPPLY..........................................................................17

9-2. TEST 2 THERMISTOR TEST --- MEASURE WITH POWER OFF .......................................18

9-3. TEST 3 MOTOR TEST ................................................................................................19

9-4. TEST 4 MOISTURE SENSOR ....................................................................................20

9-5. TEST 5 DOOR SWITCH TEST ...................................................................................21

9-6. TEST 6 HEATER SWITCH TEST - ELECTRIC TYPE...........................................................22

9-7. TEST 7 GAS VALVE TEST - GAS TYPE .........................................................................23

10. CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) ...............................................24

11. DISASSEMBLY INSTRUCTIONS .........................................................................................26

12. EXPLODED VIEW ..............................................................................................................32

12-1. CONTROL PANEL & PLATE ASSEMBLY .......................................................................32

12-2. CABINET & DOOR ASSEMBLY...................................................................................33

12-3-1. DRUM & MOTOR ASSEMBLY : ELECTRIC TYPE ........................................................34

12-3-2. DRUM & MOTOR ASSEMBLY : GAS TYPE ...............................................................35

13. REPLACEMENT PARTS LIST ................................................................................................36

CONTENTS

Equipped

Temperature

Moisture

Equipped

Adopted

Equipped

27" x 42

3/4" x 28 1/3"

29 1/2" x 44 3/4" x 30 3/4"

On / Off

High / Low / OffHigh / Low / Off

Equipped

Stainless Steel

Equipped

Sensor

126 / 144

Door Trim

Top Plate

Color

WhiteChromeSilver

Painted

PorcelainPorcelain

White

Titanium

120V / 240V 60Hz (26A)POWER SUPPLY

LAMP

HEATER

MOTOR

599

7.3 cu.ft.

Electronic

15W (125mA)

GAS VALVE

13W (110mA) X 2

5400W (22.5A)

555

250W (4.5A)

ELECTRICITY

CONSUMPTION

White

Material &

Finishes

DLE2532WDLE5932SDLE5932W

DLG2532W

DLG5932SDLG5932W

ITEM

Child lock

Reversible Door

Interior Light

Product (WXHXD)

Packing (WXHXD)

Audible End of Cycle Beeper

Dryer Rack

Drum

No. of Dry Levels

No. of Dry Option

No. of Programs

DRUM CAPACITY

CONTROL TYPE

No. of Temperature Controls

Weight (lbs): Net / Gross

AC 120V

( GAS TYPE)

AC 240V

( ELECTRIC TYPE)

Thermistor

Electro sensor

AC 120V

REMARK

SPECIFICATIONS

FEATURES AND BENEFITS

DLE5911W / DLG5911W

DLE2511W / DLG2511W

DLE5932W / DLG5932W / DLE5932S / DLG5932S

DLE2532W / DLG2532W

3-1. POWER CORD

INSTALLATION INSTRUCTIONS

1) 4-wire connection

1. External ground connector - Dotted line shows

position of NEUTRAL ground wire before being

moved to center terminal block screw

2. Center silver-colored terminal block screw

3. Green wire of harness

1. External ground connector

2. Green or bare copper wire of power supply cord

3. 3/4 in. (1.9 cm) UL-listed strain relief

4. Center silver-colored terminal block screw

5. Neutral grounding wire (green)

6. Neutral wire (white)

5. Connect the other wires to outer terminal block

screws. Tighten screws.

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer

rear panel Secure cover with hold-down screw.

3. Connect ground wire (green or bare) of power

supply cable to external ground conductor screw.

Tighten screw.

4. Connect neutral wire (white or center wire) of

power supply cord to the center, silver colored

terminal screw of the terminal block.

1. 4-wire receptacle (NEMA type 14-30R)

2. 4-prong plug

3. Ground prong

4. Neutral prong

5. Spade terminals with upturned ends

6. 3/4 in. (1.9 cm) UL approved strain relief

7. Ring terminals

1. Remove center terminal block screw.

2. Remove appliance ground wire (green) from

external ground connector screw. Fasten it under

center, silver colored terminal block screw.

IMPORTANT: A 4-wire connection is

required for mobile

homes and where local

codes do not permit the

use of 3 wire connections.

3 4 5 7

2) 3-wire connection

Use where local codes permit connecting

cabinet-ground conductor to neutral wire.

1. Remove center terminal block screw.

2. Remove appliance ground wire (green) from

external ground connector screw. Connect

appliance ground wire and the neutral wire (white

or center wire) of power supply cord/cable under

center, silver colored terminal block screw.

Tighten screw.

3. Connect the other wires to outer terminal block

screws. Tighten screws.

Use where local codes permit connecting

cabinet-ground conductor to neutral wire.

3) Optional 3-wire connection

1. Loosen or remove center terminal block screw.

Connect neutral wire (white or center wire) of

power supply cord to the center, silver colored

terminal screw of the terminal block. Tighten screw.

1. External ground connector

2. Neutral grounding wire (green)

3. Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. 3/4 in. (1.9 cm) UL-listed strain relief

3. Connect the other wires to outer terminal block

screws. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer

rear panel. Secure cover with hold-down screw.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer

rear panel. Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the

external ground connector screw to an adequate

ground.

1. External ground connector

2. Neutral grounding wire (green)

3. Neutral wire (white or center wire)

Grounding path determined by a qualified electrician

1. 3-wire receptacle (NEMA type 10-30R)

2. 3-wire plug

3. Neutral prong

4. Spade terminals with up turned ends

5. 3/4 in. (1.9 cm) UL approved strain relief

6. Ring terminals

7. Neutral (white or center wire)

3-2. Connect Gas Supply Pipe (Gas Dryer ONLY)

1. Make certain your dryer is equipped for use with the

type of gas in your laundry room. Dryer is equipped

at the factory for Natural Gas with a 3/8” N.P.T. gas

connection.

2. Remove the shipping cap from the gas connection

at the rear of the dryer. Make sure you do not

damage the pipe thread when removing the cap.

3. Connect to gas supply pipe using a new flexible

stainless steel connector.

4. Tighten all connections securely. Turn on gas and

check all pipe connections (internal & external) for

gas leaks with a non-corrosive leak detection fluid.

5. For L.P. (Liquefied Petroleum) gas connection, refer

to section on Gas Requirements.

For further assistance, refer to section on Gas Requirements.

1 New Stainless Steel Flexible Connector - Use

only if allowed by local codes (Use Design

A.G.A. Certified Connector)

2 1/8” N.P.T. Pipe Plug

(for checking inlet gas pressure)

3 Equipment Shut-Off Valve-Installed within 6’

(1.8 m) of dryer

4 Black Iron Pipe

Shorter than 20’ (6.1 m) - Use 3/8” pipe

Longer than 20’ (6.1 m) - Use 1/2” pipe

5 3/8” N.P.T. Gas Connection

Time

COLUMBUS DRYER CYCLE PROCESS

Cycle

Heavy Duty

3Hr

Off Time: 6min

On Time: 10sec

Temperature Control for each cycle

High

Medium

High

Medium

Low

Extra

low

(High)

(Medium

High)

Cotton/

Towel

Normal

Perm.

Permanent

Press

Delicate

Ultra

Delicate

Speed dry

Freshen Up

Air dry

(Normal)

54min Saturation

Saturation

55min

41min

36min

32min

34min

25min

min

(5min)

N/A

70±5°C

66±5°C

62±5°C

55±5°C

45±5°C

(70±5°C)

(66±5°C)

heater

47±5°C

38±5°C

(47±5°C)

N/A

Saturation

Load

Sense

Dry *

Manual

Dry **

Default

Drying

Electro-

sensor

Temp-

Control

Default

time

Temp-

Control **

Cooling Wrinkle care

Conditions of operation and termination

Temp-

erature

Dry

Level

Display

time

Motor

Heater

* Sense dry : “Dry Level” is set by users.

** Manual dry : “Temperature control” is set by users.

Default settings can be adjusted by users.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG Trockner Handbücher

LG DLE8377WM Bedienungsanleitung

LG DLG7101 Series Bedienungsanleitung

LG WT7155CW-DLE7150W Bedienungsanleitung

LG TD-C8031E Bedienungsanleitung

LG DLE7000 Series Bedienungsanleitung

LG DL 730 E Series Bedienungsanleitung

LG DLG1102W Bedienungsanleitung

LG DLEX9000 Series Bedienungsanleitung

LG DLEX3360R Bedienungsanleitung

LG DLG2522W Bedienungsanleitung

LG DLG2302R Bedienungsanleitung

LG DF50BV2BR Bedienungsanleitung

LG GD1329CGW Bedienungsanleitung

LG Steam Dryer DLEX2650 Series Bedienungsanleitung

LG DL 340 Series Bedienungsanleitung

LG DLEX5101W Bedienungsanleitung

LG FDV708W Bedienungsanleitung

LG DGS2028EKD Bedienungsanleitung

LG DLHX4072 series Betriebsanleitung

LG DLE0442G Bedienungsanleitung

LG DLE2150 Bedienungsanleitung

LG RC8055AH1Z Bedienungsanleitung

LG DLGX2551R Bedienungsanleitung

LG DLEX2501 Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung