LG DLEX3885 Series Bedienungsanleitung

ELECTRIC & GAS DRYER

SERVICE MANUAL

CAUTION

READ THIS MANUAL CAREFULLY IN ORDER TO

PROPERLY DIAGNOSE PROBLEMS AND TO SAFELY

PROVIDE QUALITY SERVICE ON THESE DRYERS.

U.S.A. Website: http://us.lgservice.com

Canadian Website: http://lg.ca

MODEL : Electric Gas

DLEX3885* DLGX3886*

DLEX3875* DLGX3876*

JAN. 2010 PRINTED IN KOREA P/No.: MFL62119907

To avoid personal injury, disconnect power before servicing this product. If electrical power is required

for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks.

WARNING !

WHAT TO DO IF YOU SMELL GAS:

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by individuals possessing skill and experience in

electrical, electronic, and mechanical appliance repair. Any attempt to repair a major appliance may result

in personal injury and property damage. The manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume any liability in connection with its use.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are

removed for service, they must be returned to their original position and properly fastened.

IMPORTANT

Electrostatic Discharge (ESD)

Sensitive Electronics

ESD problems are present everywhere. ESD may damage or weaken the electronic

control assembly. The new control assembly may appear to work well after repair is

finished, but failure may occur at a later date due to ESD stress.

■Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted

metal in the appliance.

- OR -

Touch your finger repeatedly to a green ground connection point or unpainted metal

in the appliance.

■Before removing the part from its package, touch the anti-static bag to a green ground connection

point or unpainted metal in the appliance.

■

Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.

■When repackaging failed electronic control assembly in anti-static bag, observe above instructions.

■Do not try to light a match, or cigarette, or turn on

any gas or electrical appliance.

■Do not touch any electrical switches. Do not use

any phone in your building.

■Clear the room, building or area of all occupants.

■Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions carefully.

■If you cannot reach your gas supplier, call the fire

department.

CONTENTS

1. SPECIFICATIONS ............................................................................................................... 4

2. FEATURES AND BENEFITS ............................................................................................... 6

3. INSTALLATION INSTRUCTIONS ........................................................................................ 6

4. DRYER CYCLE PROCESS ................................................................................................ 13

5. COMPONENT TESTING INFORMATION ......................................................................... 14

6. MOTOR DIAGRAM AND SCHEMATIC ............................................................................. 17

7. WIRING DIAGRAM ............................................................................................................ 18

8. STEAM FUNCTION ............................................................................................................ 19

8-1. STEAM CYCLE GUIDE ............................................................................................ 19

8-2. TROUBLESHOOTING FOR STEAM DRYER .......................................................... 20

8-3. DISPLAY FAULT/ERROR CODES FOR STEAM DRYER ........................................ 21

9. FLOW SENSOR FUNCTION ............................................................................................. 22

9-1. FLOW SENSOR ....................................................................................................... 22

9-2. INSTALLATION CHECK .......................................................................................... 23

9-3. TROUBLESHOOTING FOR FLOW SENSOR DRYER ............................................ 24

10. DIAGNOSTIC TEST ........................................................................................................ 25

10-1. TEST 1 120V AC ELECTRICAL SUPPLY ............................................................ 26

10-2. TEST 2 THERMISTOR TEST - MEZSURE WITH POWER OFF ......................... 29

10-3. TEST 3 MOTOR TEST ......................................................................................... 30

10-4. TEST 4 MOISTURE SENSOR .............................................................................. 31

10-5. TEST 5 DOOR SWITCH TEST ............................................................................. 32

10-6. TEST 6 HEATER SWITCH TEST - ELECTRIC TYPE .......................................... 33

10-7. TEST 7 GAS VALVE TEST - GAS TYPE .............................................................. 34

10-8. TEST 8 SEMI-CONDUCTOR ............................................................................... 35

10-9. TEST 9 MOTOR ASSEMBLY, DC, PUMP ............................................................ 35

10-10. TEST 10 GENERATOR ASSEMBLY .................................................................. 36

11. CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) ....................................... 37

12. DISASSEMBLY INSTRUCTIONS .................................................................................... 39

13. EXPLODED VIEW ............................................................................................................ 49

13-1-1. Control Panel and Plate Assembly (Touch LCD type) ......................................... 49

13-1-2. Control Panel and Plate Assembly 50

13-2. PANEL DRAWER ASSEMBLY and GUIDE ASSEMBLY ......................................... 51

13-3-1. CABINET and DOOR ASSEMBLY: ELECTRIC TYPE ........................................ 52

13-3-2. CABINET and DOOR ASSEMBLY: GAS TYPE .................................................. 53

13-4-1. DRUM and MOTOR ASSEMBLY: ELECTRIC TYPE ........................................... 54

13-4-2. DRUM and MOTOR ASSEMBLY: GAS TYPE ..................................................... 55

1SPECIFICATIONS

Name: Electric and Gas Dryer

Power supply: Please refer to the rating label regarding detailed

information.

Specifications are subject to change by manufacturer.

See page 7 See page 8

Size : 27 X 30 X 38.7 (inch)

Dryer capacity: IEC 7.4 cu.ft.

Weight: 136(lbs)

Pedestal (1 each)

Purchased Separately

Stacking kit (1 each)

Purchased Separately

ACCESSORIES

See page 6

Dryer rack (1 each)

Sound levels

ITEM

DLEX3885* DLGX3886*

DLEX3875* DLGX3876* REMARK

Blue White / Stainless Silver / Vintage Gold

Porcelain

Color

Top Plate

Door Trim

ELECTRICITY

CONSUMPTION

MOTOR

HEATER

LAMP

GAS VALVE

AG HEATER

DC, PUMP

CONTROL TYPE

DRUM CAPACITY

Weight (lbs) - Net/Gross

No. of Programs

No. of Dry Options

No. of Temperature Controls

Moisture

Temperature

No. of Dry Levels

Reversible Door

Drum

Dryer Rack

Child Lock

Interior Light

Product (WxHxD)

Sensor

POWER SUPPLY

Material &

Finish

Chromate

120V/240V 60Hz (26A)

250W (4.5A)

5400W (22.5A)

15 W (0.2A)

13 W (0.11A) x 2

1100W (9.2A)

2.4W (0.15A)

Electronic

7.4 cu.ft.

136 / 155.7

Available

Stainless Steel

Available

27" x 42 3/4" x 28 1/3"

Packing (WxHxD) 29 1/2" x 44 3/4" x 30 3/4"

AC 120V

AC 240V (ELECTRIC MODEL)

AC 120V

AC 120V (GAS MODEL)

AC 120V (STEAM MODEL)

DC 9V (STEAM MODEL)

Thermistor, Dual Sensor

Electrode sensor, Dual Sensor

2FEATURES AND BENEFITS

3INSTALLATION INSTRUCTIONS

Dryer Rack Installation Instructions

Open the door.

Hold the dryer rack

with both hands.

Put the dryer rack into

the drum

Check and be sure that the

front of the rack is properly

seated behind the lint filter.

Peel the protective paper from the tape on

the side bracket.

Secure the side bracket to the washer with

a screw on the back of the bracket. Repeat

Steps 2, 3, and 4 for the other side.

Place the dryer on top of the washer by

placing the legs as shown. Be careful not to

pinch fingers between the washer and dryer.

Slide the dryer back against the stop on the

side rail.

Fit the side bracket firmly to the side of the

top plate by attaching the double-faced tape

to the top plate as picture shown.

Insert the front rail of the stacking kit. Push

the front rail back against the stops on the

side brackets.

• Do not use a stacking kit with a gas dryer in

potentially unstable conditions like a mobile

home.

Stacking Kit Installation Instructions

Place the washer firmly on a stable, even

and solid floor as product installation

instructions describe in the owner’s

manual.

Do not attempt this alone!

At least two people are required to lift and

position the dryer on top of a washing

machine!

Failure to heed this warning can result in

serious physical injury and damage to the

appliance.

WWAARRNNIINNGG

Stacking kit

Attach the front bracket to the side rails with

a screw on each side.

To ensure safe and secure installation, please observe the instructions below.

Pedestal Installation Instructions

The pedestal accessory includes:

•Drawer divider (1) •Wrench (1)

•Screws (18) † •T-clips (4) ††

Tools Needed for Installation:

•Phillips-head screwdriver

•Wrench (supplied)

† Dryer installation only uses 8 screws

†† For dryer only

To ensure safe and secure installation, please

thoroughly follow the instructions below.

•Incorrect installation can cause serious accidents.

•The appliances are heavy. Two or more people are

required when installing the pedestal. There is a

risk of serious back injury or other injuries.

• Do not allow children to play in or on the drawer.

There is a risk of suffocation or injury.

• Do not step on the handle. There is a risk of serious injury.

• If appliances are already installed, disconnect them

from all power, water, or gas lines and from draining or

venting connections. Failure to do so can result in

electrical shock, fire, explosion, or death.

• When installing, gloves must be put on.

WARNING

Retract fully

Retainer

T-clip

Make sure the leveling feet of the dryer are

fully retracted.

NOTE: The appliance and pedestal assembly

must be placed on a solid, sturdy, level floor

for proper operation.

Insert the T-clip of the 4 retainers into the dryer

base as shown. Press up on the back of the

clip and pull outward to lock into place.

Place the dryer on the

pedestal. Make sure

the front and back feet

are in the correct

positions. The dryer

feet will fit into the

innermost positions as

shown.

Make sure the screws on the pedestal align with the

holes in the retainers, then install 4 screws on each

side to securely attach the appliance to the pedestal.

NOTE: If the screws are not installed properly, noise

and vibration may result.

Move the appliance to the desired location.

Securely tighten all locknuts by hand.

NOTE: Noise and vibration may result if locknuts are not

tightened.

Be sure to connect the appliances to all water, power,

or gas lines and draining or venting connections before

operation.

If there is excessive vibration during the first operation

after installation, slightly adjust the leveling feet.

Loosen the locknuts on all 4 leveling feet of the

pedestal until you can turn them with the wrench.

Turn clockwise to raise or counterclockwise to lower

until the pedestal is level and all 4 feet are solidly

against the floor.

For dryer

For washer/combo

Raise Lower

Locknut

Use the instructions under option 2 or 3 if your

home has a 3-wire receptacle (NEMA type 10-30R).

Use option 2 if local codes and ordinances permit

the connection of a chassis ground to the neutral

connector. If this is not permitted, use option 3.

Review the following options to determine the appropriate electrical connection for your home:

Electric Dryer Only

If this type is available at your home. you will be

connecting to a fused disconnect or circuit breaker

box

Important :Grounding through the neutral conductor

is prohibited for (1) new branch-circuit installations,

(2) mobile homes, and (3) recreational vehicles, and

(4) areas where local codes prohibit grounding through

the neutral conductor.

Prepare minimum 5ft(1.52m) of length in order for

dryer to be replaced.

First, peel 5 inch (12.7cm) of covering material from

end. Make a 5 inch of ground wire bared. After cutting

/2inch (3.8cm) from 3 other wires. peel insulation

back 1inch (2.5cm). Make ends of 3 wires a hook

shape.

Then, put the hooked shape end of the wire under the

screw of the terminal block(hooked end facing rightward)

and pinch the hook together and screw tightly.

Use the instructions under option 1 if your home

homehas a 4-wire receptacle (NEMA type 14-30R).

If this type is available at your home. you will be

connecting to a fused disconnect or circuit breaker

box

1. Connect neutral wire(white) of power cord to center

terminal block screw.

2. Connect red and black wire to the left and right

terminal block screws.

3. Connect ground wire(green) of power cord to external

ground screw and move neutral ground wire of

appliance and connect it to center screw.

4. Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on tight and

power cord is in right position.

(2.5 cm)

(12.7 cm)

3-wire direct

4-wire receptacle

(NEMA type14-30R)

3-wire receptacle

(NEMA type10-30R)

4-wire direct

(12.7 cm)

4-wire connection : Direct wire

(2.5 cm)

(12.7 cm)

Andere Handbücher für DLEX3885 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG Trockner Handbücher

LG RV1329AD1 Bedienungsanleitung

LG DF50 V2S6W Series Bedienungsanleitung

LG DLE2512W Bedienungsanleitung

LG D7188RM Bedienungsanleitung

LG DLEX4270W Bedienungsanleitung

LG TD-C8012A Bedienungsanleitung

LG DLE2350W Bedienungsanleitung

LG DLEX5680 Bedienungsanleitung

LG DLEX7700*E Bedienungsanleitung

LG RC09VHP2V Bedienungsanleitung

LG DLE0442W Bedienungsanleitung

LG WF-D90PW Bedienungsanleitung

LG DLEX8100V Bedienungsanleitung

LG RH1077 VK Series Bedienungsanleitung

LG DLEX4371 Series Bedienungsanleitung

LG DLE8377 Bedienungsanleitung

LG DLHC1455W Bedienungsanleitung

LG DLE9577SM Bedienungsanleitung

LG DLE2601R Bedienungsanleitung

LG SteamDryer DLGX3251W Bedienungsanleitung

LG DLEX4370 Series Bedienungsanleitung

LG TDD16517S Bedienungsanleitung

LG DLGX3251 Series Bedienungsanleitung

LG DLE3500 series Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung