LG 17MB15P Bedienungsanleitung
www.lg.com
17MB15P
LED MONITOR MODEL
Please read this manual carefully before operating your set
and retain it for future reference.
Owner's Manual
LED MONITOR
(LED MONITOR*)
*LG LED Monitors are LCD Monitors with LED Backlighting.
1
Accessories
!!! Thank for selecting LGE products !!!
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
User's Guide/Cards Power Cord
15-pin D-Sub Signal Cable
(To set it up, this signal cable may be
attached to this product before
shipping out.)
DVI-D Signal Cable
(This feature is not available in all
countries.)
NOTE
This accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite
cores to maintain standard compliance for the product.
Cable Holder Stand Base
2
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2.Assemble the Stand Base into the Stand Body.
Be sure don't pull out the Stop Pin and make the Stand Base direction as shown.
Stand Base
Stand Body
Stop Pin
Important
This illustration depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and get
damaged or injure your foot.
3.Make the monitor stand,then pull out the Stop Pin.
WARNING :
The tape and locking pin may only be removed from those monitors
equipped with a standing base when the base is pulled up. Otherwise, you
may be injured by the protruding sections of the stand.
FRONT
Side
Stop Pin
Stop Pin
pull out the stop pin
3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚ to 25˚
Height Range : maximum 4.33 inches (110.0 mm)
First ,remove the
locking pin.
110.0 mm
E
rgonomic
I
t is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle
of the monitor should not exceed 5 degrees.
4
Connecting the Display
ERGONOMIC
I
t is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt
angle of the monitor should not exceed 5 degrees.
WARNING
You do not need to replace the Locking pin after it is removed, to adjust its height.
When adjusting the angle of the screen, do not put your finger(s) in
between the head of the monitor and the stand body. You can hurt your
finger(s).
When adjusting the height of the screen, do not put your finger(s) in
between the head of the monitor and the stand base. You can hurt your
finger(s).
5
Connecting the Display
-The pivot function allows you to rotate the screen 90 degrees clockwise.
1.
Lift the monitor to its highest height to utilize the Pivot function.
2.Landscape & Portrait : You can rotate the panel 90o clockwise.
Please be cautious and avoid contact between the monitor head and the
Stand Base when rotating the screen to access the Pivot function. If the
monitor head touches the Stand Base, then the Stand Base could crack.
3.
Be careful with the cables when rotating the screen.
Using the Pivot function
Stand section
Head section
6
Connecting the Display
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals.
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution.
A
B
Connect DVI-D(Digital signal) Cable
Connect D-sub(Analog signal) Cable
1. Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
2.
Connect signal input cable and power cord in order, then tighten the screw
of the signal cable.
Connecting with the PC
12
Wall-outlet type
Mac adapter : For Apple Macintosh use, a
separate plug adapter is needed to change the
15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin 2
row connector.
When using a D-Sub signal input cable connector
for Macintosh
Varies according to model.
DVI-D (This feature is not available in all countries.)
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
3. Press the power button on the front panel to turn the power on. When monitor power is
turned on, the 'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
Connect the signal
input cable and tighten
it up by turning in the
direction of the arrow
as shown in the figure.
7
Control Panel Functions
Front Panel Controls
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
8
Control Panel Functions
AUTO/SET Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button prior to entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
17 inch:1280 x 1024
Power Button
Use this button to turn the display on or off.
The indicator lights up as blue when the display is
operating normally (On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator changes to flicker.
Power Indicator
Buttons
Use this button to select or adjust functions in the On
Screen Display.
SOURCE
Use this button to make D-Sub or DVI connector
active.This feature is used when two computers are
connected to the display.The default setting is D-
Sub.
Use this button to select an icon in the On Screen
Display.
9
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of the
display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls. The
following section is an outline of the available adjustments and selections you can
make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the or Buttons.When the icon you want
becomes highlighted,press the AUTO/SET Button.
Use the / Buttons to adjust the image to the desired level.
Use the AUTO/SET Button to select other sub-menu items.
Push the MENU Button once to return to the main menu to select another
function .Push the MENU Button twice to exit from the OSD.
NOTE
Allow the display to stabillize for at least 30 minutes before making image adjustments.
Inhaltsverzeichnis
Andere LG Monitor Handbücher
LG
LG 47WX50MF-B Bedienungsanleitung
LG
LG W2252V-PF Bedienungsanleitung
LG
LG 28MQ780-B Bedienungsanleitung
LG
LG W1943SE-PF Bedienungsanleitung
LG
LG MU-60PZ12V Bedienungsanleitung
LG
LG 29WP60G Bedienungsanleitung
LG
LG Flatron L1953S-BF Bedienungsanleitung
LG
LG L1760TG Bedienungsanleitung
LG
LG LC370WXN-SAB1-621 Bedienungsanleitung
LG
LG Flatron W2053TQ Bedienungsanleitung
LG
LG L1930SQ Bedienungsanleitung
LG
LG UltraGear 48GQ900-B.AEU Bedienungsanleitung
LG
LG Flatron W2242S Bedienungsanleitung
LG
LG 27EN43V-B Bedienungsanleitung
LG
LG 32SQ730S Bedienungsanleitung
LG
LG 24BN650Y-T Bedienungsanleitung
LG
LG 49WQ900G Bedienungsanleitung
LG
LG M3203CG Bedienungsanleitung
LG
LG FLATRON M3201C Bedienungsanleitung
LG
LG Genesis G-Probe Bedienungsanleitung
