LG 26TS30MF Bedienungsanleitung
•Openframe
•Media Player
•Transparent
•Video Wall
•Other Models
•Accessories
MONITOR SIGNAGE MODELS
V3.2
1 OPENFRAME SIGNAGE
1-1. Keep temperature (Mandatory)
1-2. Consider using a cooling & heater solution(Mandatory)
1-3. Do not disassemble Handle, Fan or Side bracket(Mandatory)
1-4. Check Screw hole depth to avoid LCD panel damage(Mandatory)
1-5. Please install cooling system when exposed to direct sun light(Mandatory)
1-6. Use the side bracket to mount into an enclosure
1-7. Refer to brightness of according to ambient luminance
1-8. How to measure fan noise when it is installed indoors
1-9. Be careful not to damage the cable within an enclosure
2 MEDIA PLAYER
2-1. Install dust filter & keep temperature 0°C ~ 40°C(Mandatory)
2-2. Minimum distance between media player and structure(100mm)
2-3. the importance of periodic cleaning for ventilation area (Mandatory)
3 TRANSPARENT SIGNAGE
3-1. Preparation for Installation
3-2. Portrait mode: Rotate the set clockwise 90°(Mandatory)
3-3. Attach the product by using the screw holes (Mandatory)
3-4. How to connect cable assembly
3-5. Reference guide to the ventilation hole of enclosure
3-6. Reference guide to lighting set up
3-7. Reference to storage place(AD Board & Media Player)
3-8. Dimension of screw holes(26TS30MF/47TS30MF)
3-9. Recommendation: Lighting should be 600 LUX or more
3-10. Recommendation of operation Time
4 VIDEO WALL
4-1. Precaution when moving and handling
4-2. Installing the product
4-3. Tiling Displays (How to join Sets)
4-4. How to daisy chain monitors
4-5. Function Setting(Multivision Configuration)
4-6. Setting the Installation Menu
4-7. Setting the Tile Mode
4-8. Setting the Picture ID
4-9. The Heat Distribution of 47WV30
CONTENTS
2
4-10. Guide for installing the signage to reduce gap
4-11. White Balance Calibration Instruction
4-12. How to prevent the panel falling out
584WS70(84 inch UD Signage)
5-1. Keep temperature 0°C ~ 40°C(Mandatory)
5-2. The Handles are removable
5-3. Do not use a screw that is longer than 19.8mm (Mandatory)
5-4. Dimension of 84WS70MS
5-5. Use the Eye-Bolt Bracket to lift
5-6. Use the vesa screw holes for stand
5-7. Guide for Screw Size (Mandatory)
6 The other check point
6-1. Do not install such as face down or face up direction
6-2. Avoid installing the in-door signage at out-door
6-3. Guide for installing when product is close to the window
6-4. The TV module applied model & Image sticking
6-5. Enclosure design guide to prevent dust (Indoor)
6-6. Check the Baud Rate & RS-232C cable
6-7. Keep the distance for embedded installation
6-8. Firmware update by SuperSignElite-c
6-9. Guide for how to install correctly to the bracket
6-10. How to check Signage power off history
6-11. Digital Signage SW download method
6-12. SuperSign SW download method
6-13. Signage SW version box label mark
6-14. Avoid installing the product at oily environment when mounting
to the wall by using a wall mounting bracket
6-15. Check the Input Label when Signage is set up with a PC/Media Player
6-16. Do not spray directly onto the screen when cleaning the monitor
by using a cleaning liquid
6-17. Check the Guide Spacer when installing wall mount
6-18. Be careful not to fall off the wall metal material
6-19. Check the USB device is bad or not
CONTENTS
3
7 Accessories
7-1. How to connect the Stand
7-2. How to clean Touch Overlay
7-3. How to connect the OPS with KT-OPSA
CONTENTS
4
OPENFRAME SIGNAGE
1-1. Keep temperature (Mandatory)
When designing the enclosure, the temperature inside the enclosure must be maintained
as optimal temperature
The Measurement method for checking the operating temperature inside the enclosure
Enclosure
Openframe Signage (eg. 47WX50MF)
5cm
Thermal sensor
5cm
5cm Example
1. Should install a thermal sensor inside the enclosure.
There are three location for thermal sensor.
(backside of the top , backside of the middle,
backside of the bottom)
2. On this basis of you measuring the temperature,
Ensuring that you keep the temperature
47WX50MF
> 0°C ~ 40°C
72WX70MF
> 0°C ~ 50°C
5
1-2. Consider using a cooling & heater solution (Mandatory)
To maintain the temperature inside the enclosure, you should consider using a cooling
and heater solution such as an air conditioner, heat exchanger, or combined cooler
and heater depending on the external environment. (Please see below examples)
You could also employ an air flow circulation system and air curtain* between the front
panel and the enclosure.
Example 2 : Enclosure (Heat exchanger)Example 1 : Enclosure (Just fans)
Example 4 : Direct Air Cooling SolutionExample 3 : Enclosure (Air conditioner)
Air Curtain Air Curtain
Air Curtain Air Curtain
Heater
Membrane Filter
FAN
Humidity Sensor
Protection
glass
Recommend to design the exterior of the enclosure to meet with the IP65 standard.
Use a dust filter to prevent dust .(At air inlet and outlet )
Filter should be used for filtering out bugs, dust and water.
For preventing from rust of lead frame in circuit board,
operates the Heater if relative humidity is high.
*Air curtain :
Air flow circulation system between
the front panel and the enclosure. 6
1-3. Do not disassemble Handle, Fan or Side bracket (Mandatory)
Do not disassemble the parts such as Handle, Fan or Side bracket
for preventing of product safety & function problem
Handle
Side bracket
Fan
*47WX50MF
47WX50MF
72WX70MF (No Handle, Side bracket)
Fan
1
2
[ Rear side ]
7
1-4. Check Screw hole depth to avoid LCD panel damage(Mandatory)
You must use the side screw holes when mounting the panel
The Side screw holes are M4.0 Tap , Torque 4~5Kgf.cm, pitch 0.7mm
The Screw hole depth of the panel is: 9.0mm (Max)
If a screw is longer than 9.0mm, it may cause damage to the LCD panel
It is advisable to only use spring washer-type screws.
Side Hole
47WX50MF
47WX50MF
▪Example : Spring washer type
8
You must use the side screw holes when mounting the panel
The Side screw holes are M6.0 Tap ,Torque 4~5Kgf
(Top and bottom sides: 5 holes for each, left and right sides: 3holes for each)
The Screw hole depth of the panel is:16.0mm(Max)
If a screw is longer than 16.0mm, it may cause damage to the LCD panel
47WX50MF
Side screw hole of panel
72WX70MF
72WX70MF
9
1-5. Please install a cooling system when exposed to direct
sun light (Mandatory)
NOTE
•To prevent sunlight, consider to attach a UV film on the glass
•For Example-Using a canopy may prevent the enclosure temperature increasing
due to direct sunlight.
Example
10
Andere Handbücher für 26TS30MF
1
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere LG Monitor Handbücher
LG
LG Flatron L1722P Bedienungsanleitung
LG
LG N1642M Bedienungsanleitung
LG
LG 43UN700P-B.AEK Bedienungsanleitung
LG
LG 32VS10MN Bedienungsanleitung
LG
LG L1730PSUPM Bedienungsanleitung
LG
LG L2000CM Bedienungsanleitung
LG
LG UltraGear 25GR75FG-B.AEUQ Bedienungsanleitung
LG
LG Flatron W1943C Bedienungsanleitung
LG
LG 27UL550P-W Bedienungsanleitung
LG
LG UltraGear 27GL83A Bedienungsanleitung
LG
LG 27HJ712C Bedienungsanleitung
LG
LG 24MP88HM Bedienungsanleitung
LG
LG L1930SQ Bedienungsanleitung
LG
LG E2341V Bedienungsanleitung
LG
LG M1510S Bedienungsanleitung
LG
LG M4224CG Bedienungsanleitung
LG
LG E2242V Bedienungsanleitung
LG
LG MT-60PZ90V Bedienungsanleitung
LG
LG 27UP850 Bedienungsanleitung
LG
LG FLATRON L1550S-SN Bedienungsanleitung
