LG D2242P Bedienungsanleitung
www.lg.com
OWNER’S MANUAL
CINEMA 3D MONITOR
D2242P
D2542P
Please read this manual carefully before operating
your set and retain it for future reference.
CINEMA 3D MONITOR MODEL
ENGLISH
2
ENG
ENGLISH
TABLE OF CONTENTS
CONTENTS
3ASSEMBLING AND PREPARING
3 Unpacking
4 Parts and buttons
6 Setting up the Monitor set
6 - Attaching the Stand Base
6 - Detaching the Stand Base and Body
7 - Mounting on a table
8 - Mounting on a wall
10 USING THE MONITOR SET
10 Connecting to a PC
10 - D-SUB connection
10 - DVI-D connection
10 - HDMI connection
12 CUSTOMIZING SETTINGS
12 Accessing The Main Menus
13 Customizing Settings
13 - Menu Settings
14 - 3D Settings(Only 3D mode)
14 - Volume Settings (Only supported in
HDMI)
15 - SUPER ENERGY SAVING Settings
16 TROUBLESHOOTING
18 TROUBLESHOOTING WHEN
USING 3D MODE
19 SPECIFICATIONS
21 Preset Modes (Resolution)
21 HDMI 3D TIMING
21 Indicator
22 PRECAUTIONS TO TAKE
WHEN VIEWING 3D IMAGES
23 PROPER POSTURE
23 Proper posture for using the Monitor set.
23 Precautions to take when viewing 3D im-
ages
3
ENG
ENGLISH
ASSEMBLING AND PREPARING
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
yDo not use any unapproved accessories to ensure the safety and product life span.
yAny damages or injuries by using unapproved accessories are not covered by the warranty.
yThe accessories supplied with your product may vary depending on the model.
yProduct specifications or contents in this manual may be changed without prior notice due to upgrade
of product functions.
yUser should use shielded signal interface cables (RGB cable / DVI-D cable) with ferrite cores to
maintain standard compliance for the product.
CAUTION
NOTE
Stand Base
Stand Body
Power Cord
CD(Owner's Manual) /
Card
TriDef 3D software Program CD /
Quick Installation Guide
D-SUB Cable
(This signal cable may be attached
to this product before shipping out.)
DVI-D Cable
(This cable is not included in all
countries.)
3D Glasses
(Normal type)
3D Glasses
(Clip-on type)
4
ENG
ENGLISH
ASSEMBLING AND PREPARING
Parts and buttons
HDMID-SUB
AC-IN/
䔜㹷彺⅌ DVI-D
Power Indicator
yLighting On: Turned on
yLighting Off: Turned off
Connection panel (See p.10)
Button (See p.12)
(Power Button)
5
ENG
ENGLISH
ASSEMBLING AND PREPARING
Button Description
MENU Accesses the main menus.(See p.13)
OSD LOCKED/
UNLOCKED
This function allows you to lock the current control settings, so
that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message "OSD
UNLOCKED" should appear.
SUPER ENERGY
SAVING Button
Use this button to enter SUPER ENERGY SAVING menu.For
more information.(See p.15)
3D 3D display settings.(See p.14)
AUTO When adjusting your display settings, always press the AUTO button on the MONITOR
SETUP OSD. (Only supported in Analog Mode)
The best display mode 1920 x 1080 (D2242P/D2542P)
VOLUME (Only HDMI mode) Adjust the volume of the Monitor set.(See p.14)
INPUT You can choose the input signal.
yWhen two input signals are at least are connected, you can select the input signal
(D-SUB/DVI/HDMI) you want.
yWhen only one signal is connected, it is automatically detected. The default setting is
D-SUB.
EXIT Exit the OSD(On Screen Display).
(Power Button) Turns the power on or off.
Power Indicator The power indicator stays blue if the display is running
properly (On Mode). If the display is in Sleep Mode, the power
indicator blinks blue.
6
ENG
ENGLISH
ASSEMBLING AND PREPARING
Setting up the Monitor set
Attaching the Stand Base
1Place the Monitor set with the screen side
down on a flat and cushioned surface.
Lay a foam mat or soft protective cloth
on the surface to protect the screen from
damage.
yThis illustration depicts the general model of
connection. Your monitor may differ from the
items shown in the picture.
yDo not carry the product upside down holding
only the stand base. The product may fall
and get damaged or injure your foot.
CAUTION
CAUTION
Detaching the Stand Base and Body
1Place the Monitor set with the screen side
down on a flat and cushioned surface.
2Pull out the Stand Base and Stand Body from
the Monitor set.
3Attach the Stand Base and then tighten the
screw to the right with a Coin.
2Assemble the Stand Body into the product in
the correct direction as shown in the picture.
Make sure you push it until you hear it “click”.
3Turn the screw to the left with a Coin, and then
pull out the Stand Base from the Stand Body.
Stand Body
Stand Base
Hinge Body
7
ENG
ENGLISH
ASSEMBLING AND PREPARING
Mounting on a table
1Lift and tilt the Monitor set into its upright
position on a table.
Leave a 10 cm (minimum) space from the wall
for proper ventilation.
2Connect the Power Cord to a wall outlet.
3Press (Power) button on the front switch
panel to turn the power on.
10 cm
10 cm
10 cm
10 cm
When you adjust the angle, do not hold the
bottom of the Monitor set frame as shown on
the following illustration, as may injure your
fingers.
Do not touch or press the screen when
adjusting the angle of the monitor.
WARNING
Unplug the power cord before moving the
Monitor to another location. Otherwise electric
shock may occur.
Tilt from +15 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.
CAUTION
NOTE
Front Rear
15- 5
8
ENG
ENGLISH
ASSEMBLING AND PREPARING
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
Please use VESA standard as below.
y784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
y787.4 mm (31.0 inch) and above
* Please use VESA standard wall mount pad
and screws.
10 cm
10 cm
10 cm
10 cm
Using the Kensington security system
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit
http://www.kensington.com
.
Connect the Kensington security system cable
between the Monitor set and a table.
The Kensington security system is optional.
You can obtain it from most electronics stores.
NOTE
9
ENG
ENGLISH
ASSEMBLING AND PREPARING
yDisconnect the power cord first, and then
move or install the Monitor set. Otherwise
electric shock may occur.
yIf you install the Monitor set on a ceiling or
slanted wall, it may fall and result in severe
injury.
yUse only an authorized LG wall mount
and contact the local dealer or qualified
personnel.
yDo not over tighten the screws as this may
cause damage to the Monitor set and void
your warranty.
yUse only screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
yUse the screws that are listed on the VESA
standard screw specifications.
yThe wall mount kit will include an installation
manual and necessary parts.
yThe wall mount bracket is optional. You can
obtain additional accessories from your local
dealer.
yThe length of screws may differ depending
on the wall mount. Be sure to use the proper
length.
yFor more information, refer to the
instructions supplied with the wall mount.
CAUTION
NOTE
Model D2242P D2542P
VESA (A x B) 75 x 75 100 x 200
Standard screw M4 M4
Number of screws 4 4
Wall mount bracket
(optional)
RW120 RW120
10
ENG
ENGLISH
USING THE MONITOR SET
USING THE MONITOR SET
Connecting to a PC
yYour Monitor set supports Plug & Play*.
*Plug & Play: A PC recognizes a connected
device that users connect to a PC and turn
on, without device configuration or user
intervention.
D-SUB connection
Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set
with the supplied D-sub 15 pin signal cable as
shown in the following illustrations.
yMac adapter
For Apple Macintosh use, a separate plug
adapter is needed to change the 15 pin
high density (3 row) D-SUB VGA connector
on the supplied cable to a 15 pin 2 row
connector.
yWhen using a D-Sub signal input cable
connector for Macintosh
yIf you use HDMI PC, it can cause compatibility
problem.
NOTE
NOTE
H
D
MI
D-SUB
DVI
-D
RGB OUT
H
D
MI
D
-
S
U
B
DVI OUT
DVI-D
HDMI
D
-
S
U
B
HDMI OUT
DVI
-D
HDMI OUT
DVI-D connection
Transmits a digital video signal from your PC to
the Monitor set. Connect the PC and the Monitor
set with a DVI cable as shown in the following
illustrations.
HDMI connection
Transmits the digital video and audio signals from
your PC or A/V to the Monitor set. Connect the PC
or A/V and the Monitor set with the HDMI cable as
shown in the following illustrations.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere LG Monitor Handbücher
LG
LG 32UN550 Bedienungsanleitung
LG
LG 34WL500 Bedienungsanleitung
LG
LG W2242PK Bedienungsanleitung
LG
LG 27QP88DP Bedienungsanleitung
LG
LG M1910SB Bedienungsanleitung
LG
LG N1941W-PF - - 18.5" LCD Monitor Bedienungsanleitung
LG
LG L1755T Bedienungsanleitung
LG
LG 27MP60GP Bedienungsanleitung
LG
LG L1752H Bedienungsanleitung
LG
LG MU-50PZ90V Bedienungsanleitung
LG
LG Flatron L1770HQ Bedienungsanleitung
LG
LG 55EW5PG Bedienungsanleitung
LG
LG 35WN65C Bedienungsanleitung
LG
LG 22MP48D Bedienungsanleitung
LG
LG 22M45VQ Bedienungsanleitung
LG
LG L1960TR Bedienungsanleitung
LG
LG L1942PE Bedienungsanleitung
LG
LG UltraGear 27GQ40W Bedienungsanleitung
LG
LG 34WN750-B.AAU Bedienungsanleitung
LG
LG L17MM Bedienungsanleitung
