LG FLATRON LCD 568LM Bedienungsanleitung

2001 PCTEST LAB

ATTACHMENT J — USER’S MANUAL

P/NO : 3828TUL193T (S-0107) Printed in Korea

Please read this manual carefully before operating your set.

Retain it for future reference.

Record model number and serial number of the set.

See the label attached on the back cover and quote this

information to your dealer when you require service.

http://www.lge.com

Color Monitor

LCD 568LM

User’s Guide

Introduction

The Monitor has an active matrix TFT (Thin-Film Transistor) LCD (Liquid

Crystal Display).

This monitor is designed for use in small working areas or for those who need

more working space on the desk.

Features

The Monitor is a 15inch (15 inches viewable) intelligent micropro-cessor based

monitor.

Digitally controlled auto-scanning is done with the microprocessor for horizontal

scan frequencies between 31 and 61kHz, and vertical scan frequencies

between 56 and 75Hz.

The microprocessor-based digital controls allow you to adjust conveniently a

variety of image controls by using the OSD (On Screen Display).

The monitor is shipped with 14 factory pre-programmed video modes that are

permanently resident. In addition, there are 16 user-storable modes, for a total

of 30 memory modes.

Plug and play capability if supported by your system.

This monitor has DDC 2B function.*

Compliant with the following regulated specifications :*

EPA ENERGY STAR

Swedish TCO’99

ENGLISH

For detailed information, please refer to the Reference Guide provided .

Connecting the Monitor

To set up the monitor, ensure that the power is turned off to the monitor,

computer system, and other attached devices, then follow these steps:

Place the monitor in a convenient, well-ventilated location near your computer.

Power off both the monitor and Computer.

Slightly press and pull the latch on Stand cover.

Connect the end of monitor signal cable to the connector at the rear panel

of your monitor throught the slot and cable holder on Stand. Connect the other

end to the 15-pin connector on the rear panel of the computer and tighten the

screws. Be sure the signal cable aligns with the 15-pin connector.

Connect the end of monitor signal cable to the connector at the rear panel

of your monitor throught the slot and cable holder on Stand. Connect the other

end of the monitor signal cable to the rear panel of Macintosh computer

through a Macintosh adapter and then tighten screws.

Connect the plug from the AC adapter into the base of the monitor.

Connect one end of the AC power cord to the AC adapter and the other

end to a properly grounded AC outlet that is easily accessible and close to the

monitor.

After connecting cables, put stand cover correctly into the holes unders stand.

If securely connected, you can hear click sound from the latch.

Power ON the PC, then the monitor.

If you see the NO SIGNAL message, check the signal cable and connectors.

After using the system, power OFF the monitor, then the PC.

IBM PC

MACINTOSH

D-15P

Mac Adapter

24V

AUDIO

DCOUT

Power Cord

Signal Cable AC adapter

D-15P

Stand cover

Latch

*NOTE : If you see the “OUT OF

RANGE” message, check to make

sure your system is set to one of the

factory preset modes.(see page A9)

Connecting the Monitor

24V

AUDIO

DCOUT

Connection the Audio

Location and Function of Controls

Rear View

Front View

AUTO

VOL

MUTE MENU

SET

24V

AUDIO

DCOUT

D-Sub Signal Connector

Stand Cover

Power Button

Power Indicator

MENU Button

MUTE Button

Buttons

AUTO/SET Button

DC Power Connecter

12V

VESA wall mounting

Connected to another

object (stand type and

wall-mounted type

- optional)

Kensington Security Slot

Connected to a locking

cable that can be

purchased separately at

most computer stores

NOTE : This monitor accept a 75mm x 75mm VESA-compliant mounting interface pad.

Control Panel Function

Front Panel Controls

AUTO

VOL

MUTE MENU

SET

Use this button to enter and from the on

screen display (OSD).

Use this button to turn the audio on or off.

Use these buttons to choose or adjust items in

the on screen display.

MENU Button

MUTE Button

Buttons

This indicator lights up green when the

monitor operates normally. If the monitor is in

DPM (Energy Saving) mode (stand-by/

suspend/power off), this indicator color

changes to amber.

Power (DPMS)

Indicator

Use this button to turn the monitor on or off.Power Button

Use this button to enter a selection in the on

screen display.

* AUTO adjustment function

Touch the AUTO/SET button before using OSD menu.

This button is for the automatic adjustment of the screen

position, clock and phase.

Note: Some signal from some graphics boards may not function

properly. If the results are unsatisfactory, adjust your monitor’s

Position, Clock and Phase manually.

AUTO/SET

Button

Control Function

MUTE Button

MENU Button AUTO/SET Button

Power Button

Power (DPMS) Indicator

Buttons

PROCESSING

AUTO CONFIGURATION

MUTE

VOL

AUTO

SET

Making adjustments to the image size, position and operating parameters of

the monitor are quick and easy with the On Screen Display Control system. A

quick example is given below to familiarize you with the use of the controls.

Following section is an outline of the available adjustments and selections you

can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the MENU Button, then the main menu of the OSD appears.

To access a control, use the Buttons. When the icon you want

becomes highlighted, press the AUTO/SET Button.

Use the Buttons to adjust the item to the desired level.

Accept the changes by pressing the AUTO/SET Button.

Exit the OSD by Pressing the MENU Button.

On Screen Display (OSD) Control Adjustment

NOTE

Allow the monitor to stabilize for at least 30 minutes before making image adjustment.

On Screen Display(OSD) Selection and Adjustment

You were introduced to the procedure of selection and adjusting an item

using the OSD system. Listed below are the icons, icon names, and icon

descriptions of the items that are shown on the Menu.

OSD Adjust Description

100

BRIGHTNESS CONTRAST

9300K 6500K

COLOR

PRESET

RED

GREEN

BLUE

POSITION

Brightness

Used to adjust the brightness of the

screen.

Contrast

Adjust the display to the contrast

desired.

PRESET

RED

GREEN

BLUE

9300K/ 6500K

To appear the displays color

temperature.

•9300K:Slightly bluish white.

•6500K:Slightly reddish white.

To set your own color levels.

Vertical Positio

To move image up and down.

Horizontal Position

To move picture image left and right.

Inhaltsverzeichnis

Andere LG Monitor Handbücher

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

Sceptre

Sceptre D40 Bedienungsanleitung