LG MFL67652408 Bedienungsanleitung
Owner's Manual
Laser Display install guide
Please read the safety information carefully before using the product.
www.lg.com
P/NO : MFL67652408(1302-REV00)
2Safety Precautions
Safety Precautions
Please take note of the safety instructions to prevent any potential accident or misuse
of the product.
Safety precautions are given in two forms, i.e. Warning and Caution as detailed be-
low.
WARNING: Failure to follow the instructions may cause serious injury and even
death.
CAUTION: Failure to follow the instructions may cause minor injury or damage to
the product.
Read the owner's manual carefully and keep it to hand.
CAUTION
Follow the instructions in the manual
to install the product.
- Otherwise, it may cause serious
injury or damage to the product.
When installing the product or ad-
justing the height of the product, two
or more people are needed.
- If you do it by yourself, you may
drop the product causing personal
injury or damage to the product.
When installing the product, check
whether the wall is strong enough to
hold the product and use the an-
chors and screws provided.
- Otherwise, they may not bear the
weight of the product causing safety
issues.
Installation
WARNING
The product should be installed by a
qualified professional specified by the
retail store.
- The product installation by a non-
qualified personnel is dangerous
and may cause personal injury.
The product should be installed
where its weight can be supported.
- Otherwise, the product may fall and
cause personal injury.
When moving or replacing the prod-
uct after installation, contact a quali-
fied installer specified by the retail
store.
- If an unqualified person moves and
installs the product, this may cause
safety issues as this task requires
the special technique.
Do not hang on the product or apply
shock to the product.
- The product may fall and cause
injury.
3
Safety Precautions
When drilling the holes in the wall,
make sure you use a drill and a drill
bit with the specified size of diameter.
Ensure that you also follow the in-
structions regarding the depth of the
holes.
- Otherwise, the product may be
installed improperly causing safety
issues.
Do not clean the product with wet
towels, and do not use a heater or
humidifier underneath the product.
- Moisture permeating into the
product, steam or heat may result in
fire, electric shock or damage to the
product.
Keep the product away from sprin-
klers, sensors, high-tension wires
and power sources. Do not install the
product in a location where vibrations
or shock impacts are likely to occur.
Wear working gloves when installing
the product. Do not use bare hands.
- Otherwise, it may cause personal
injury.
4PREPARATION
PREPARATION
Accessories
Check the accessories provided with the product.
The picture may be different from the actual product.
Accessories are subject to change without prior notice in order to improve the perfor-
mance of the product. New accessories may be added or old ones may be removed.
Preparations
Ø8 mm drill bit for concrete, leveler, tapeline, driver, tape
Ez Bracket Fixed component Connection rods,
2EA
Rubber
packings, 6EA
Fixing nuts, 2EA Guide pins, 2EA Adjustable
wrench (3 mm) Spanner
Plate Screw 1EA
(M5 x 12 mm)
5
INSTALLATION
INSTALLATION
How to fix anchors and screws
CAUTION
Check the wall materials and the thickness of finishing materials.
You can use the anchors and bolts provided with the Laser Display set for walls
made from concrete, lightweight concrete, soft fieldstone, hard fieldstone, brick
or cellular blocks.
When installing it on a wall not specified in this manual, make sure each fixing
point withstands an uplifting load of 70 kgf (686 N) and a shearing load of 100
kgf (980 N) or more.
(Attach a plate such as plywood to strengthen the wall before installation.)
a. At each anchor position, use a 8 mm drill bit to make a hole with a depth of
80 mm - 100 mm.
b. Clean the holes.
c. Insert the anchors provided into each hole.
(Use a hammer when inserting the anchor.)
d. Fix a part in place by aligning it with the screw hole.
Tighten the screw with a torque 45 kgf/cm - 60 kgf/cm or higher.
ab
c
d
Anchor
Fixing ring and space steel
Drilling hole Cleaning hole
Inserting anchor
Screw for fixing ring and
space steel
Screw for fixing ring and space steel
6INSTALLATION
Installation Procedure (Stand Type)
1 Install the guide pins at the bottom of the set.
2 Connect the connection rod to the Ez bracket main unit and place it on a table,
without the fixed components, at the center of the screen.
NOTE
Do not assemble the fixed components to the unit yet.
7
INSTALLATION
3
If the Ez bracket does not stay level, attach a rubber to the bottom of the bracket to
make it level.
(If you cannot make it level using a rubber, remove or add a plate. To add a plate,
make sure to use screws that came with the product.)
NOTE
If you cannot make it level by attaching a rubber, remove or add a plate. (To add a
plate, make sure to use screws that came with the product.)
4
Place the Laser Display onto the Ez bracket by aligning the guide pins and the holes
on the adjustable bracket.
8INSTALLATION
5 Attach 390 mm of guide tapes to the top of the table referring the sides of Laser
Display so that the tapes are vertically upward.
390 mm Guide tape
390 mm
Up
Down
Paper screen
Adjustable bracket
Table
Center line
NOTE
The figure above illustrates the fixed components which are not fixed yet.
6 Attach the paper screen above the tape. Refer to the guide tape to keep it level.
(The paper screen helps to easily install the adjustable bracket and bore holes in the wall.)
7 Place the Ez bracket with the Laser Display installed close to the wall.
8 Turn on the power on the Laser Display.
9
INSTALLATION
9 Adjust the Ez bracket by following the Laser Display screen adjustment steps to
make the size of the projection screen equal to that of the paper screen. Position
the projection screen, aligning it with the black line of the paper screen.
(If there is a gap larger than 10 mm between the projection screen and the paper
screen, mark the screen position on the paper screen and make holes in four
places.)
CAUTION
When adjusting the screen with the paper screen, do not move the Ez bracket to
the left or right.
If it is necessary to move the bracket, detach the paper screen first. If you make
too many left/right adjustments, further adjustments may be not be possible due
to lack of marginal space when actually attaching and using the screen.
10 mm
Paper screen
Projection screen
10 INSTALLATION
10 Place guide tape on both sides of the paper screen in parallel with it. Position the
tape about 40 mm above the paper screen.
The tape is used as a reference guide to help easy screen installation.
Up
Down
Ф 8
40 mm
Tape
11 Make holes using an 8 mm drill at specified positions and detach the paper screen.
12 Insert the anchors into the four holes.
13 Fix rings into the two upper holes and space steels to the two lower holes using
8 mm bolts.
Attach three magnets to the space steels fixed at the bottom.
3 magnets
Space steel
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere LG Monitor Handbücher
LG
LG Flatron LM505J Bedienungsanleitung
LG
LG FLATRON L1952H Installations- und Betriebshandbuch
LG
LG M2901SCBN Bedienungsanleitung
LG
LG 22MK600M Bedienungsanleitung
LG
LG Flatron W2343S Bedienungsanleitung
LG
LG L1915S - - 19" LCD Monitor Bedienungsanleitung
LG
LG 27BK750Y-B.AHK Bedienungsanleitung
LG
LG 34UC89G Bedienungsanleitung
LG
LG W2271TC Bedienungsanleitung
LG
LG Flatron L1710S(K) Series Bedienungsanleitung
LG
LG UltraGear 27GL650F-B Bedienungsanleitung
LG
LG 23ET83V Bedienungsanleitung
LG
LG L224WS Bedienungsanleitung
LG
LG 49UH5C Bedienungsanleitung
LG
LG FLATRON L1717S Bedienungsanleitung
LG
LG UltraGear 32GN50T Bedienungsanleitung
LG
LG 34WP88CN Bedienungsanleitung
LG
LG UltraGear 27GQ50F Bedienungsanleitung
LG
LG UltraGear 27GL63T Bedienungsanleitung
LG
LG 216SC Bedienungsanleitung
