LG LRMDS3006 Series Bedienungsanleitung

11INSTALLATION

ENGLISH

INSTALLATION

Before Installing

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to

another location.

aUnpacking the Refrigerator

bChoosing the Proper Location

cDisassembling/Assembling

dConnecting the Water Line

eLeveling and Door Alignment

WARNING

• Connect to potable water supply only.

us_main.book.book Page 11 Friday, February 7, 2020 11:44 AM

12 INSTALLATION

Unpacking the Refrigerator

WARNING

• Use two or more people to move and install the

refrigerator. Failure to do so can result in back

injury or other injury.

• The refrigerator is heavy. Protect the floor when

moving the refrigerator for cleaning or service.

Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage could

occur.

• Keep flammable materials and vapors, such as

gasoline, away from the refrigerator. Failure to

do so can result in fire, explosion, or death.

NOTE

• Remove tape and any temporary labels from

your refrigerator before using. Do not remove

any warning labels, the model and serial number

label, or the Tech Sheet that is located under the

front of the refrigerator.

• To remove any remaining tape or glue, rub the

area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a

small amount of liquid dish soap over the

adhesive with your fingers. Wipe with warm

water and dry.

• Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the

surface of your refrigerator.

• Reinstall or adjust shelves as needed.

Refrigerator shelves are installed in the shipping

position. Reinstall shelves according to your

individual storage needs.

Choosing the Proper

Location

Water

Must be located where a water supply can be

connected for the automatic icemaker.

NOTE

• The water pressure must be 20 - 120 psi or 138 -

827 kPa or 1.4 - 8.4 kgf/cm2. If the refrigerator is

installed in an area with low water pressure

(below 20 psi or 138 kPa or 1.4 kgf/cm2), you can

install a booster pump to compensate for the

low pressure.

Electricity

Use an individual, grounded outlet:115 Volts, 60

Hz, AC, 15 Amps minimum.

WARNING

• Do not overload house wiring and cause a fire

hazard by plugging in multiple appliances in the

same outlet with the refrigerator.

• To reduce the risk of electric shock, do not install

the refrigerator in a wet or damp area.

Flooring

To avoid noise and vibration, the unit must be

installed and leveled on a solidly constructed floor.

If required, adjust the leveling legs to compensate

for the unevenness of the floor.

NOTE

• Installing on carpeting, soft tile surfaces, a

platform or weakly supported structure is not

recommended.

Ambient Temperature

Install this appliance in an area where the

temperature is between 55 °F (13 °C) and 110 °F

(43 °C).

If the temperature around the appliance is too low

or high, cooling ability may be adversely affected.

us_main.book.book Page 12 Friday, February 7, 2020 11:44 AM

13INSTALLATION

ENGLISH

Dimensions and Clearances

• Check the dimensions of the appliance and the installation path to ensure there is sufficient room to

move the refrigerator through doors or narrow openings.

• If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/

Assembling the Doors and Drawers in this manual.

• The installation location chosen for the refrigerator should allow space behind the unit for connections

and airflow and space in front to open the doors and drawers.

• Too small of a distance from adjacent items may result in lowered freezing capability and increased

electricity consumption charges. Allow at least 24 inches (610 mm) in front of the refrigerator to open the

doors, and at least 2 inches (50.8 mm) between the back of the refrigerator and the wall.

-Dimension/Clearance LRMDS3006* LRMDC2306*

LRMVS3006* LRMVC2306*

A Depth without Handle 35 2/3" (906 mm) 28 7/9" (731 mm)

B Width 35 3/4" (908 mm) 35 3/4" (908 mm)

C Height to Top of Case 69" (1753 mm) 69" (1753 mm)

D Height to Top of Hinge 70 1/4" (1785 mm) 70 1/4" (1785 mm)

E Back Clearance 2" (50 mm) 2" (50 mm)

F Depth without Door 31" (785 mm) 24" (610 mm)

G Depth with Handle 38 1/9" (968 mm) 31 2/9" (793 mm)

H Depth (Total with Freezer Drawer

Open)

59 3/8" (1508 mm) 47 3/4" (1213 mm)

I Depth (Total with Door Open 90°) 50" (1270 mm) 43 1/9" (1095 mm)

us_main.book.book Page 13 Friday, February 7, 2020 11:44 AM

14 INSTALLATION

Removing/Assembling

Handles

When moving the refrigerator through a narrow

opening, removing the doors is preferred.

The appearance of the handles may vary from

what is shown.

CAUTION

• When assembling or disassembling the

refrigerator handles, grasp the handle firmly to

avoid dropping it.

• Do not swing the handle into nearby people or

animals.

• Make sure that the bracket hole of the handle

fits properly into the stopper bolt of the door.

Assemble the set screws to fix the handle into

place.

• Make sure that there is not a gap between the

door and handle after assembling the handle.

• Tools Needed

- 3/32 in. Allen wrench

- 1/8 in. Allen wrench

- 1/4 in. Allen wrench

Removing Refrigerator Handles

1 Loosen the set screws awith a 3/32 in. Allen

wrench and remove the handle.

2 Loosen the mounting fasteners bthat

connect to the refrigerator door and handle

using a 1/4 in. Allen wrench, and remove the

mounting fasteners.

Assembling Refrigerator Handles

1 Assemble the mounting fasteners aat both

ends of the handle with a 1/4 in. Allen wrench.

2 Place the handle on the door by fitting the

handle footprints over the mounting

fasteners and tightening the set screws b

with a 3/32 in. Allen wrench.

Removing Freezer Drawer Handles

1 Loosen the set screws alocated on the lower

side of the handle with a 1/8 in. Allen wrench

and remove the handle.

2 Loosen the mounting fasteners bwith a 1/4

in. Allen wrench, and remove the mounting

fasteners.

Assembling Freezer Drawer

Handles

1 Assemble the mounting fasteners aat both

ends of the handle with a 1/4 in. Allen wrench.

2 Place the handle on the door by fitting the

handle footprints over the mounting

fasteners and tightening the set screws b

with a 1/8 in. Allen wrench.

us_main.book.book Page 14 Friday, February 7, 2020 11:44 AM

15INSTALLATION

ENGLISH

Removing/Assembling

Doors and Drawers

If the entrance door is too narrow for the

refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway.

WARNING

• Use two or more people to remove and install

the refrigerator doors and freezer drawer.

• Disconnect the electrical supply to the

refrigerator before installing.

• Do not put hands, feet or other objects into the

air vents or bottom of the refrigerator.

• Be careful when handling the hinge and stopper.

• Remove food and bins before detaching the

doors and drawer.

• Do not hold the handle when removing or

replacing the doors and drawer as the handle

may come off.

Tools Needed

3/32 in. Allen wrench

1/8 in. Allen wrench

1/4 in. Allen wrench

Removing the Hinge Cover

Remove the screws from the hinge cover at the top

of the refrigerator. Lift the hook (not visible),

located at the bottom of the front side of the cover

with a flat-head screwdriver.

Removing the Left Refrigerator

Door

1 The water supply is connected to the upper

right part of the rear surface of the

refrigerator. Remove the clip in the joint area.

Hold the water supply connection and gently

push the collet ato detach the water supply

line as shown.

NOTE

• Disassembling/Assembling the Water Lines

bCollet cTube dInsert line eClip

2 Pull out the water supply lines f. Disconnect

all the wire harnesses g. Unscrew the

ground wire h.

3 Rotate the hinge lever icounterclockwise.

Lift the top hinge jfree of the hinge lever

latch k.

CAUTION

• When lifting the hinge free of the latch, be

careful that the door does not fall forward.

us_main.book.book Page 15 Friday, February 7, 2020 11:44 AM

16 INSTALLATION

4 Lift the door from the middle hinge pin and

remove the door.

CAUTION

• Place the door, inside facing up, on a

nonscratching surface.

Removing the Right Refrigerator

Door

1 Detach all the wire harnesses a. Unscrew the

ground wire b.

NOTE

• The number of wire harnesses may vary

depending on the model.

• Ground wire is only available on some models.

2 Rotate the hinge lever cclockwise. Lift the

top hinge dfree of the hinge lever latch e.

CAUTION

• When lifting the hinge free of the latch, be

careful that the door does not fall forward.

3 Lift the door from the middle hinge pin and

remove the door.

CAUTION

• Place the door, inside facing up, on a

nonscratching surface.

Assembling the Right Refrigerator

Door

CAUTION

• Install the right-side door first.

1 Make sure that the plastic sleeve is inserted in

the bottom of the door. Lower the door onto

the middle hinge pin as shown in the figure.

2 Fit the hinge aover the hinge lever latch b

and slot it into place. Rotate the lever c

counterclockwise to secure the hinge.

us_main.book.book Page 16 Friday, February 7, 2020 11:44 AM

17INSTALLATION

ENGLISH

3 Connect all the wire harnesses dand the

ground screw e.

NOTE

• The number of wire harnesses may vary

depending on the model.

• Ground wire is only available on some models.

Assembling the Left Refrigerator

Door

CAUTION

• Install the left refrigerator door after the right

door is installed.

1 Make sure that the plastic sleeve is inserted in

the bottom of the door. Install the refrigerator

door onto the middle hinge.

2 Fit the hinge aover the hinge lever latch b

and slot it into place. Rotate the lever c

clockwise and fasten the hinge.

3 Connect all the wire harnesses and the

ground wire.

4 Push the water supply lines into the hole on

the top case and pull them through the

backplate.

5 Hold the water supply connection and gently

push in the collet dto connect the water

supply lines as shown. Insert the tube at least

5/8 inch (15 mm) into the connector. Insert

the clip on the joint to fasten the tubes in

place.

NOTE

• Disassembling/Assembling the Water Lines

eCollet fTube gInsert line hClip

us_main.book.book Page 17 Friday, February 7, 2020 11:44 AM

18 INSTALLATION

NOTE

• Gently press the collet and insert the tube until

only one line shows on the tube.

Removing the Full Convert Drawer

1 Pull the drawer open to full extension.

Remove the basket from the rails.

2 Hold both sides of the door and remove it

from the rails.

Assembling the Full Convert

Drawer

1 Grasp the door on each side and lower it into

place on the rails.

2 Pull the drawer open to full extension. Lower

the basket onto the rails.

Removing the Freezer Drawer

WARNING

• Use two or more people to remove and install

the refrigerator doors and freezer drawer.

• Be careful of sharp hinges on both sides of the

drawer.

• When you lay the drawer down, be careful not to

damage the floor.

• Do not sit or stand on the freezer drawer.

• To prevent accidents, keep children and pets

away from the drawer. Do not leave the drawer

open. If the Durabase®storage bin is removed

from the freezer drawer, there is sufficient space

for a small child or pet to crawl inside.

1 Pull the drawer open to full extension.

2 Gently lift and pull out the ice bin.

3 Lift the front of the drawer up, then pull it

straight out.

us_main.book.book Page 18 Friday, February 7, 2020 11:44 AM

19INSTALLATION

ENGLISH

4 Remove the Durabase basket from the rails.

Remove the screws from the rails at both

ends.

5 Grip both sides of the drawer and pull it up to

remove it from the rails.

CAUTION

• Do not hold the handle when removing or

replacing the drawer. The handle may come off,

causing personal injury.

6 Hold both rails and push them in

simultaneously.

Assembling the Freezer Drawer

1 Pull out both rails simultaneously, until they

are fully extended.

2 Grasp the drawer on each side and hook the

drawer supports into the rail tabs located on

both sides.

CAUTION

• Do not hold the handle when removing or

replacing the drawer. The handle may come off,

causing personal injury.

3 Lower the door into its final position and

insert the screws in the rails on both sides.

us_main.book.book Page 19 Friday, February 7, 2020 11:44 AM

20 INSTALLATION

4 Insert the drawer into the frame, and push

the drawer back until it clicks into place.

5 Replace the ice bin in the drawer. Insert the

Durabase basket in the rail assembly.

Assembling the Hinge Cover

Position the hinge cover in its place. Insert and

tighten the cover screws.

Connecting the Water Line

Before Beginning

This water line installation is not covered by the

refrigerator warranty. Follow these instructions

carefully to minimize the risk of expensive water

damage.

If necessary, call a qualified plumber to correct

water hammer before installing the water supply

line to the refrigerator. Water banging in the

pipes, or water hammer in residential plumbing

can cause damage to refrigerator parts and lead to

water leakage or flooding.

• Turn the icemaker OFF if the refrigerator will be

used before the water line is connected.

• Do not install the icemaker tubing in areas

where the ambient temperatures fall below

freezing.

WARNING

• Connect to potable water supply only.

CAUTION

• To prevent burns and product damage, only

connect the refrigerator water line to a cold

water supply.

• Wear eye protection during installation to

prevent injury.

Water Pressure

You will need a cold water supply.

Water Pressure

•models with water filter:

- 20 - 120 psi (138 - 827 kPa)

•where reverse osmosis water filtration

system is connected to a cold water supply:

- 40 - 60 psi minimum to reverse osmosis

system (2.8 kgf/cm2- 4.2 kgf/cm2, or less than

2 - 3 seconds to fill a cup of 7 oz capacity)

If the water pressure from the reverse osmosis

system is less than 20 psi or 138 kPa or 1.4 kgf/cm2

(takes more than 4 seconds to fill a cup of 7 oz or

198 cc capacity):

• Check to see if the sediment filter in the reverse

osmosis system is blocked. Replace the filter if

necessary.

• Allow the storage tank on the reverse osmosis

system to refill after heavy usage.

us_main.book.book Page 20 Friday, February 7, 2020 11:44 AM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG Kühlschrank Handbücher

LG GR-S462QVC Bedienungsanleitung

LG LRFD22850ST Bedienungsanleitung

LG LRSC 26945TT, LRSC 26944TT, LRSC 26930TT, LRSC 26922TT, LRSC 26920TT, LRSC 26911TT, LRSC 26910TT, LRSC 26944SW, LRSC 26930SW,... Bedienungsanleitung

LG GN-U262 Bedienungsanleitung

LG LSC26905 Series Bedienungsanleitung

LG GR-L207QRFA Bedienungsanleitung

LG LMXS30786S Bedienungsanleitung

LG LSFXC2496S Bedienungsanleitung

LG SXS Series Bedienungsanleitung

LG WG1804R Bedienungsanleitung

LG LTC24380SB Montageanleitung

LG GL-200KMLG Bedienungsanleitung

LG GC-379BVA Bedienungsanleitung

LG GR-M4924CPN Bedienungsanleitung

LG LFC23760ST - Bottom Freezer Refrigerator Bedienungsanleitung

LG LFC25770ST - 25.0 cu. ft. Refrigerator Bedienungsanleitung

LG LFC257**** Bedienungsanleitung

LG GC-B379BLCK Bedienungsanleitung

LG GR-Q29FTQKL Bedienungsanleitung

LG GL-B195OCOQ Bedienungsanleitung

LG LFX25975SB Bedienungsanleitung

LG LBNC10551V Bedienungsanleitung

LG LFC25765SB Bedienungsanleitung

LG LRFVS2503 Series Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung