LG LRSPC2041T Bedienungsanleitung

WARNINGS AND PRECAUTIONS FOR SAFETY

Please observe the following safety precautions in order to

use safely and correctly the refdgarator and to prevent

accident and danger dudng repair.

1. Be care of an electdc shock. Disconnect power cord

from wall ot_let and wait for more then three minutes

before replacing PWB parts. Shut off the power

whenever replacing and repairing electric components.

2. When connecting power cord, please wait for more than

five minutes after power cord was disconnected from the

wall outlet.

3. Please check if the power plug is pressed down by the

refrigerator against the wall. If the power plug was

damaged, it may cause fire or electdc shock.

4. If the wall outlet is over loaded, it may cause fire. Please

use its own individual electrioal outlet for the refrigerator.

5. Please make sure the outlet is propedy earthed,

particularly in wet or damp area.

6. Use standard electrical components when replacing

them.

7. Make sure the hook is correctly engaged.

Remove dust and foreign materials from the housing

and connecting parts.

8. Do not fray, damage, machine, heavily bend, pull out,

or twist the power cord.

9. Please check the evidence of moisture intrusion in the

electrical components. Replace the parts or mask it

with insulation tapes if moisture intrusion was

confirmed.

10. Do not touch the ioemaker with hands or tools to

confirm the operation of geared motor.

11. Do not let the customers repair, disassemble, and

reconstruct the refrigerator for themselves. It may

cause accident, electric shock, or fire.

12. DO not store flammable materials such as ether,

benzene, alcohol, chemicals, gas, or medicine in the

refrigerator.

13. Do not put flower vase, cup, cosmetics, chemicals,

etc., or container with futl of water on the top of the

refrigerator.

14. Do not put glass bottles with full of water into the

freezer. The contents shell freeze and break the glass

bottles.

15. When you scrap the refrigerator, please disconnect the

door gasket first and scrap it where children are not

accessible.

-3-

PARTS IDENTIFICATION

3. Ref No. : GR-L247ER, GR-L207ER

Ice

DispenserBurton

Cover Hinge

,_r--

Cover PWB

nt-t

> Water Tube

Freezer Refdgerator

Compartment Compartment

Automatic

ice maker

Lamp-

Shelf

holder (optional)

Box

Sheff<

(Steel,

T/Glass)

Drawer_

or Sheff

(optional)

Shelf

Door rack

Lower Covet Conversion Switch

(MeatsNegetables) Humidity Switch

drawer/Meat drawer

-14-

HOW TO INSTALL REFRIGERATOR

1. How to Adjust Door Height of Refrigerator

• Makethe refrigerator levelfirst. (If the refrigerator isnot installed onthefiat floor, the height offreezer and refdgerator

door may not be the same.)

1. If the height of freezer door is lower than that of

refrigerator compartment :

2. If the height of freezer door is higher than that of

refrigerator compartment :

/ I

t Screw t

\_ )Driver s/

Insert a ddver O into the groove 0of adjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

Insert a driver 0into the groove 0of adjuslJng screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

-18-

HOW TO INSTALL REFRIGERATOR

2. How to Install Water Pipe

•Before Installation

1. The icemaker requires the water pressure of 1.5 -

8.5kgf/cm 2. (It is acceptable if city water fills a cup of

180o:; with water for 3 seconds)

2 Install booster pump where the city water pressure is

below 1.5kgf/cm 2for normal operation of water and ice

dispenser.

3. The total length of water pipe shall be less than 12m. Do

not bend the pipe at right angle. If the length is more

than 12m, there will be troubles on water supply due to

water pressure drop,

4. Please install water pipe where there is no heat around,

2-1. When connecting directly to the water tap,

•Please confirm the following installation parts.

Valve Feed Rubber, Packing Connector. Pipe

O Co_nn_tor, Pipe Tape, Te_flon

iClass.

Conve-

rtible

Water

Valve

Water

Conn-

ector

Shape and Spec,

Connector, (MECH) Pipe

Nomenclature

Valve Feed

PINg Remarks

5221JA3001A Common Use

4932JA3003A

6631JA3004A

6631JA3004B

3920JA3001B

6631JA3004C

6631JA3004D

3920JA3001A

No Holes

4932JA3003C

6631JA3004E

6631JA3004F

392gJA3001C

Connector,(MECH)Pipe

ConversionConnector(3/4")

BalanceConector(3/4")

Pecking(e24x3t)

4932JA3003B

ConversionConnector(W25)

BalanceConectoor(W25)

Packing(_23x3t)

Connector,(MECH)Pipe

ConversionConnector0N28)

BalanceConector(W28)

Packing(e26x3L)

Connector,(MECH)Pipe

ConversionConnector(1/2")

BalanceConector(l/Z')

Packing(_l9x3t)

No Holes

4932JA3003D

6631JA3004G No Holes

6631JA3004H

3920JA3001D

-19-

HOW TO INSTALL REFRIGERATOR

1. Connection of Pipe Connector A and B.

1) Turn off main valve of water pipe.

2) Disconnect water tap from piping by loosening nuts.

3) Connect pipe connector A and B to piping after sealing

the pipe connector with sealing tapes.

4) Connect feed valve to pipe connector A.

5) If there is only one tap water pipe, connect pipe

connector A only and install feed pipe.

Caution : • Feed pipe should be connected to cold water

line. If it is connected to hot water line, trouble

may occur.

• Please check rubber packing when connecting

feed pipe.

Pipe Connector B -Feed

Valve

How to wind

Sealing Tapes.

Single Lever Type Faucet

(general) GenemlType

Feed

Valve

Two Hands Type Faucet

Feed

Valve

Single LeverType Faucet(one

hole, techtypeand hand spra_

Valve

2. Water Supply

1) After the installation of feed water, plug the refrigerator

to the earthered wall outlet, press the water dispenser

button for 2 -3minutes, and confirm that the water

comes out.

2) Check leakage at connecting part, then arrange water

tube and locate the refrigerator at its regular place if

there is no leaking.

Water Tube

-20 -

HOW TO INSTALL REFRIGERATOR

3. When customer uses bottled waten

*If customer wants to use bottled water, extra pump should be installed as shown below.

1. The pump system should not be on the floor (it may cause noise and vibration). Securely fasten the inlet and outlet

nuts of pump.

2. If there is any leakage alter installation, cut the water tube at right angle and reassemble.

3. When put the water tube end into the bottle, leave a clearance between bottle bottom and water tube end.

4 Check water coming out and any leakage.

Caution : •If feed tube is more than 4m, less water wifi come out due to pressure drops.

• Use standard feed tube to prevent leaking.

p t "_

•Outtemal Filter

1. Filter Fixation

1) Connect feed tube to the filter outlet and water valve connecting tube.

2) Fix the filter at proper piece around the sink where it is easy to replace the filter and to receive the cleaning water.

Please consider the length of tube shall be less than 12m when locating filter.

3) When fixing the filter, use fixing plate and cable depending on the surrounding conditions.

Inlet

2. Filter Cleaning

1) Connect feed tube to the inlet of feed valve and filter.

2) Clean the main valve and feed valve with water for at

least one mince until clean water comes out.

- 21 -

HotWater

Cold Water

FilterInlet

Filter_

Water

HOW TO INSTALL REFRIGERATOR

•install Water Filter (Applicable to some models only)

•Before Installing water filter

1. Before installing the filter, take out the top shelf of the

refrigerator after tilting it to the direction (C)) and lifting it

to the direction ((_)) and move it to the lower part.

2. Remove the lamp cover by pressing the protrusion

under the cover and pulling the cover to the front, lUide line

and the fastening indication line

Control box

•Installing water filter

1. Initial installation of water filter

Remove the filter substitute cap by turning it

counterclockwise ((_)) by 90 degrees and pulling it down.

Note : Keep it safe to use it later when you do not use the

filter.

Remove the red cap from the filter and attach the

sticker, Insert the upper part of the filter ((_)) after

aligning with the guideline marked on the control box,

and fasten it by turning it clockwise by 90 degrees.

Note : Check that the guideline and the fastening

indication line are aligned.

,,,,°,°

2. Replacement of water filter

While holding the lower part of the filter, turn it

countemlockwise ((_)) by 90 degrees and pull it down.

Note : Check that the guideline and the loosening

indication line are aligned.

and the looseningindicationline

•After installing water filter

Reassemble the lamp cover and the top shelf of the

refrigerator. To place the top shelf of the refrigerator, raise

the front part of the shelf abit so that the hook of the shelf

is fit into the groove.

In order to clean the water fi]ter system, drain water for

about 3 min.

Note :Then open the door of the refrigerator and check for

water droppings on the shelf under the filter.

-22 -

HOW TO INSTALL REFRIGERATOR

3. How to Control the Amount of V_ater Supplied to lcemaker.

3-1. Confirm the amount of water supplied to the icemaker.

1.Pull out the ice bank in the upper part of the freezer compartment.

Caution : • Do not put hands or tools into the chute to confirm

the operation of geared motor.

it may damage refrigerator or hurt hands.)

•Check the operation of motor with its operation

noise.

2. Apply electricity after connecting water pipe.

1) Press test switch under the icemaker for two seconds as shown below.

2) The bell dngs(ding~dong) and ice tray rotates and water comes out from the icemaker water tube.

3) The water shall be supplied two or three times into the tray. The amount of water supplied for each time is smell.

Put a water container under the ice tray and press test switch.

4) When ice tray rotates, the water in it will spill. Collect the spilt water and throw away into the sink.

5) When ice tray has finished rotation, water comes out from the water tube. Confirm the amounts of water in the ice tray.

(refer to fig. The optimum amount of water is 110cc)

Confirm the amount

_/__ /_ Icemaker

..................... Test Switch :O]

IToomooh "-. :

_=_.-_'...o;_-- Optimum level%'._ /

",_ IIToolittie .. "•.. I..

*It isacceptable if the adjusted level of water is a bit smaller than optimum level,

- 23 -

HOW TO INSTALL REFRIGERATOR

3-2. Control the amount of water supplied to the

icemaker.

Caution : -Please unplug the power cord from the wall

outlet and wait for more than three minutes

before disconnecting PWB cover as 310V is

applied in the control panel.

1. Disconnect PWB cover from the upper part of the

refrigerator.

(+) Driver

2. Adjust the amount of water supplied by using DiP

switch.

•Water Supplying Time Control Option

SWITCH NO Water Suppling

S/W1 IS/W2 S/W3 Time

OFF I 0FF 'oFF ' 6._Sec......

ON I OFF OFF 5.5 Sec.

OFF i ON OFF

ON I ON OFF

OFF ] OFF ON

i....

ON OFF ON

oFF.....5, ON

ON ..... oN ON

6 Sec.

7 Sec.

7.5 Sec.

8 Sec.

9Sac

i10 Sec.

1) The water supplying time is set at five seconds when the

refrigerator is delivered.

2) The amount of water supplied depends on the setting

time and water pressure (city water pressure).

3) If ice cube is too small, increase the water supplying

time, This happens when too small water is supplied into

the ice tray.

4) If ice cube sticks together, decrease the water supplying

time. This happens when too much water is supplied

into the ice tray,

Caution : When adjusting the amount of water supplied,

adjust step by step. Otherwise the water may

spill over.

Switch ON

Switch OFF

3. When adjustment of control switch for the amount of

water supplied is complete, check the level of water in

the ice tray.

Confirm the amount

- 24 -

MICOM FUNCTION

1. Monitor Panel

1-1, GR-P247, GR-P207, GR-L247, GR-L207 1-2. GR-C247, GR-C207, GR-B247, GR-B207

Function Monitor

t"t

,[\

/\'_

Freezer cornpertruant Refdgerator cornparWenl

temperature contzc4Button lemperatore control Button

Dispenser se_ectio_ b:Jtt0_

2. Description of Function

2-1. Funnction of Temperature Selection

Division Power Initially On 1st Press 2nd Press 3th Press 4th Press

Change of

Indication Lamp

•_= =_-':.-=- ....... == • =

_--_--I _--u=-- i I--K_-- i i--u_-- i i--t--I

@@ @@

Temperature Medium Medium Max Max Min

Control

Freezer -19 °C -22 °C -23 °C

Control (-18 °C) (-20.5 °C) (-22 °C) -15 °C

<-19 °C> <-20.5 =C> <-22 °C> <-15,5 °C>

Refrigeration 6 °C

Control 3 °C 1.5 °C 0°C (7 °C)

<2 °C> <1 °C> <0 °C> <4.5 °C>

* The ¢mtx_a tire can vary.:!:3 _Cdependingon the load condition. *( ) : 127V/6011z,110~ I15vi60llz, 115v/60Hz Rating ONLY.

*< >:TAIBEI

Medium Min

-17 °C

<-18 *C>

4.5 *C

<3 °C>

1. When power is initially applied or reapplied after power cut, =Medium" is automatically selected.

2. When the temperature selection switch in the freezer and refrigerator compartments is pressed, the light is on in the

following sequence:

"Medium" --, "Medium Max" --, "Max" _ "Min" --, "Medium Min" _ "Medium"

3. The temperature setting condition of freezer and refrigerator compartments shall not be indicate in the standard model

(GR-P247, GR-P207, GR-L247, GR-L207, GR-C247, GR-C207, GR-B247, GR-B207) when refrigerator or home bar

door is closed.

-25-

Dieses Handbuch passt für folgende Modelle

Andere LG Kühlschrank Handbücher

LG LFC25770 Series Bedienungsanleitung

LG GR-B802GVCC Bedienungsanleitung

LG GR-262SQ Bedienungsanleitung

LG GL Series Bedienungsanleitung

LG LFXC22596S Bedienungsanleitung

LG GR-L219STSL Bedienungsanleitung

LG G B352C Series Bedienungsanleitung

LG GF-B530BL Bedienungsanleitung

LG LRSXS2706 Series Bedienungsanleitung

LG LFCC22426S.ASTCNA0 Bedienungsanleitung

LG GR-B333WLRU Bedienungsanleitung

LG SxS LRSPC2661T Bedienungsanleitung

LG LDN20718 Series Bedienungsanleitung

LG GR-B802GSP Bedienungsanleitung

LG GN-B392YLC Bedienungsanleitung

LG GR-M899 Series Bedienungsanleitung

LG GR-T622 Bedienungsanleitung

LG LRFDS3006 Series Bedienungsanleitung

LG GR-M782GSHC Bedienungsanleitung

LG LSC26905SB Bedienungsanleitung

LG GR-M6780DID Bedienungsanleitung

LG GR482SF Bedienungsanleitung

LG GCX-267PHS Bedienungsanleitung

LG LTC24380SB Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung