LG LRSPC2301BS Bedienungsanleitung

WARNINGS AND PRECAUTIONS FOR SAFETY

Please observe the following safety precautions in order to

use safely and correctly the refrigerator and to prevent

accident and danger during repair.

1. Be care of an electric shock, Disconnect power cord

from wall outlet and wait for more than three minutes

before replacing PWB parts. Shut off the power

whenever replacing and repairing electric components.

2. When connecting power cord, please wait for more than

five minutes after power cord was disconnected from the

wall outlet.

3. Please check if the power plug is pressed down by the

refrigerator against the wall. If the power plug was

damaged, it may cause fire or electric shock.

4. If the wall outlet is over loaded, it may cause fire, Please

use its own individual electrical outlet for the refrigerator.

5. Please make sure the outlet is properly earthed,

particularly in wet or damp area.

6. Use standard electrical components when replacing

them.

7. Make sure the hook is correctly engaged,

Remove dust and foreign materials from the housing

and connecting parts.

Do not fray, damage, machine, heavily bend, pull out,

or twist the power cord.

Please check the evidence of moisture intrusion in the

electrical components. Replace the parts or mask it

with insulation tapes if moisture intrusion was

confirmed.

10. Do not touch the icemaker with hands or tools to

confirm the operation of geared motor.

11. Do not let the customers repair, disassemble, and

reconstruct the refrigerator for themselves. It may

cause accident, electric shock, or fire.

12. Do not store flammable materials such as ether,

benzene, alcohol, chemicals, gas, or medicine in the

refrigerator.

13. Do not put flower vase, cup, cosmetics, chemicals,

etc,, or container with full of water on the top of the

refrigerator.

14. Do not put glass bottles with full of water into the

freezer, The contents shall freeze and break the glass

bottles.

15. When you scrap the refrigerator, please disconnect the

door gasket first and scrap it where children are not

accessible.

-3-

PARTS IDENTIFICATION

3. Ref No. : GR-L247ER, GR-L207ER

Frame Display

Dispenser Lamp

Dispenser Button

Cover Hinge Cover PWB

Door rack

ice maker

Shelf

(Steel,

TIGlass)

Drawer

or Shelf

(optional)

Freezer

Compartment Refrigerator

Compartment f Milk product corner

Shelf

J Door rack

(optional)

Box

drawer

Shelf

rack

Lower Cover Conversion Switch

(MeatsNegetables) Humidity Switch

drawer/Meat drawer

-14-

HOW TO INSTALL REFRIGERATOR

1. How to Adjust Door Height of Refrigerator

•Make the refrigerator levelfirst. (If the refrigerator is notinstalled on the flat floor, the height of freezer and refrigerator

door may not be the same.)

1. If the height of freezer door is lower than that of

refrigerator compartment : 2. If the height of freezer door is higher than that of

refrigerator compartment :

Height

Difference' Height

Difference

Insert a driver 0 into the groove Oof adjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

Insert a driver 0 into the groove O of adjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

-18-

HOW TO INSTALL REFRIGERATOR

2. How to Install Water Pipe

•Before Installation

1. The icemaker requires the water pressure of 1.5

8.5kgf/cm 2. (It is acceptable if city water fills acup of

180cc with water for 3 seconds)

2. Install booster pump where the city water pressure is

below 1,5kgf/cm 2for normal operation of water and ice

dispenser.

3. The total length of water pipe shall be less than 12m, Do

not bend the pipe at right angle. If the length is more

than 12m, there will be troubles on water supply due to

water pressure drop.

4. Please install water pipe where there is no heat around.

2-1. When connecting directly to the water tap.

•Please confirm the following installation parts,

Valve Feed Rubber, Packing Connector, Pipe

Connector, Pipe Tape, Teflon

Class,

Conve-

rtible

Water

Valve

Water

Conn-

ector

Shape and Spec.

Connector, (MECH) Pipe

Nomenclature

Valve Feed

Connector,(MECH)Pipe

ConversionConnector(3/4")

BalanceCenector(3/4")

Packing(e24x3t)

4932JA3003B

ConversionConnector(W25)

BalanceConectoor(W25)

Packing(e23x3t)

P/No

5221JA3001A

4932JA3003A

6631JA3004A

6631JA3004B

3920JA3001B

6631JA3004C

6631JA3004D

3920JA3001A

Remarks

Common Use

NoHoles

Connector,(MECH)Pipe 4932JA3003C

ConversionConnector(W28) 6631JA3004E NoHoles

BalanceConector(W28) 6631JA3004F

Packing(e26x3t) 3920JA3001C

NoHoles

Connector,(MECH)Pipe

ConversionConnector(I/2")

BalanceConector(1/2")

Packing(e19x3t)

4932JA3003D

6631JA3004G

6631JA3004H

3920JA3001D

-19-

HOW TO INSTALL REFRIGERATOR

1. Connection of Pipe Connector A and B.

1) Turn off main valve of water pipe.

2) Disconnect water tap from piping by loosening nuts,

3) Connect pipe connector A and B to piping after sealing

the pipe connector with sealing tapes.

4) Connect feed valve to pipe connector A.

5) If there is only one tap water pipe, connect pipe

connector A only and install feed pipe.

Caution :•Feed pipe should be connected to cold water

line. If it is connected to hot water line, trouble

may occur,

• Please check rubber packing when connecting

feed pipe.

Pipe Connector B

\\ \Valve

How to wind

Sealing Tapes.

Single Lever Type Faucet

(general)

Two Hands Type Faucet

Feed

Valve

General Type

Single Lever Type Faucet (one

hole, tech type and hand spray)

Feed

Valve

2. Water Supply

1) After the installation of feed water, plug the refrigerator

to the earthered wall outlet, press the water dispenser

button for 2 - 3 minutes, and confirm that the water

comes out,

2) Check leakage at connecting part, then arrange water

tube and locate the refrigerator at its regular place if

there is no leaking.

Water Tube

Nut

- 20 -

HOW TO INSTALL REFRIGERATOR

3. When customer uses bottled water.

*If customer wants to use bottled water, extra pump should be installed as shown below.

1. The pump system should not be on the floor (it may cause noise and vibration). Securely fasten the inlet and outlet

nuts of pump.

2. If there is any leakage after installation, cut the water tube at right angle and reassemble.

3, When put the water tube end into the bottle, leave a clearance between bottle bottom and water tube end.

4 Check water coming out and any leakage.

Caution :• If feed tube is more than 4m, less water will come out due to pressure drops.

• Use standard feed tube to prevent leaking.

•Outternal Filter

1, Filter Fixation

1) Connect feed tube to the filter outlet and water valve connecting tube.

2) Fix the filter at proper place around the sink where it is easy to replace the filter and to receive the cleaning water.

Please consider the length of tube shall be less than 12m when locating filter.

3) When fixing the filter, use fixing plate and cable depending on the surrounding conditions.

Water Tube

Nut

Inlet

FixingPlate

2. Filter Cleaning

1) Connect feed tube to the inlet of feed valve and filter.

2) Clean the main valve and feed valve with water for at

least one minute until clean water comes out. Filter Inlet,\

Hot Water

Cold Water

Feed Valve

Water

-21 -

HOW TO INSTALL REFRIGERATOR

•Install Water Filter (Applicable to some models only)

•Before Installing water filter

1. Before installing the filter, take out the top shelf of the

refrigerator after tilting it to the direction (Q) and lifting it

to the direction (@) and move it to the lower part,

2. Remove the lamp cover by pressing the protrusion

under the cover and pulling the cover to the front.

IIl IIJ

•Installing water filter

1. Initial installation of water filter

Remove the filter substitute cap by turning it

counterclockwise ((D) by 90 degrees and pulling it down.

Note : Keep it safe to use it later when you do not use the

filter.

Remove the red cap from the filter and attach the

sticker. Insert the upper part of the filter ((!)) after

aligning with the guideline marked on the control box,

and fasten it by turning it clockwise by 90 degrees.

Note : Check that the guideline and the fastening

indication line are aligned.

Substitute

Separation_ _

of red cap____ _Aidchkes'i°n

2. Replacement of water filter

While holding the lower part of the filter, turn it

counterclockwise ((D) by 90 degrees and pull it down.

Note : Check that the guideline and the loosening

indication line are aligned.

Control box

Aligning with the guide line

and the fastening indication line

[11 q Contro,box

_'J_ Aligni_lgwith the guide line

and the loosening indication line

•After installing water filter

Reassemble the lamp cover and the top shelf of the

refrigerator. To place the top shelf of the refrigerator, raise

the front part of the shelf a bit so that the hook of the shelf

is fit into the groove.

In order to clean the water filter system, drain water for

about 3 min.

Note : Then open the door of the refrigerator and check for

water droppings on the shelf under the filter.

- 22 -

HOW TO INSTALL REFRIGERATOR

3. How to Control the Amount of Water Supplied to lcemaker.

3-1. Confirm the amount of water supplied to the icemaker.

1, Pull out the ice bank in the upper part of the freezer compartment.

Caution : • Do not put hands or tools into the chute to confirm

the operation of geared motor.

it may damage refrigerator or hurt hands.)

• Check the operation of motor with its operation

noise.

2. Apply electricity after connecting water pipe.

1) Press test switch under the icemaker for two seconds as shown below.

2) The bell rings(ding-dong) and ice tray rotates and water comes out from the icemaker water tube.

3) The water shall be supplied two or three times into the tray. The amount of water supplied for each time is small.

Put a water container under the ice tray and press test switch.

4) When ice tray rotates, the water in it will spill. Collect the spilt water and throw away into the sink.

5) When ice tray has finished rotation, water comes out from the water tube. Confirm the amounts of water in the ice tray.

(refer to fig. The optimum amount of water is 110cc)

Confirm the amount

of water

Too much -.

_-" -- Optimum level )

-.. -- _oo _lL_e ,,

Test Switch

ice maker

*it is acceptable if the adjusted level of water is a bit smaller than optimum level.

- 23 -

HOW TO INSTALL REFRIGERATOR

3-2. Control the amount of water supplied to the

icemaker.

Caution : • Please unplug the power cord from the wall

outlet and wait for more than three minutes

before disconnecting PWB cover as 310V is

applied in the control panel.

1. Disconnect PWB cover from the upper part of the

refrigerator.

(+) Driver

2. Adjust the amount of water supplied by using DIP

switch.

Caution :When adjusting the amount of water supplied,

adjust step by step. Otherwise the water may

spill over.

Switch ON

Switch OFF

3. When adjustment of control switch for the amount of

water supplied is complete, check the level of water in

the ice tray.

Confirm the amount

of water

•Water Supplying Time Control Option

SWITCH NO Water Suppling

StWl S/W2 S/W3 Time

OFF OFF OFF 6.5 Sec.

ON OFF OFF 5.5 Sec.

OFF ON OFF 6 Sec.

ON ON OFF 7 Sec.

OFF OFF ON 7.5 Sec.

ON OFF ON 8 Sec.

OFF ON ON 9 Sec.

ON ON ON 10 Sec.

"--~ _ Optimum level

1) The water supplying time is set at five seconds when the

refrigerator is delivered.

2) The amount of water supplied depends on the setting

time and water pressure (city water pressure).

3) If ice cube is too small, increase the water supplying

time. This happens when too small water is supplied into

the ice tray.

4) If ice cube sticks together, decrease the water supplying

time. This happens when too much water is supplied

into the ice tray.

- 24 -

MICOM FUNCTION

1. Monitor Panel

1-1. GR-P247, GR-P207, GR-L247, GR-L207 1-2. GR-C247, GR-C207, GR-B247, GR-B207

Function Monitor

®® ®..

/\ \_\

Freezer compartment Refrigerator compartment

temperature control Button temperature control Button

ax 5

Dispenser selection button

Q3 2 1 Min 1 2 3 45 Max

Q Q Q D D D D D

2. Description of Function

2-1. Funnction of Temperature Selection

Division

Change of

Indication Lamp

Power Initially On 1st Press 2nd Press 3th Press 4th Press

Temperature Medium Medium Max Max Min Medium Min

Control

Freezer -19 °C -22 °C -23 °C

Control (-18 °C) (-20.5 °C) (-22 °C) -15 °C -17 °C

<-19 °C> <-20.5 °C> <-22 °C> <-16.5 °C> <-18 °C>

Refrigeration 6 °C

Control 3 °C 1.5 °C O°C (7 °C) 4.5 °C

<2 °C> <1 °C> <O°C> <4.5 °C> <3 °C>

* The temperature call valy _3 °( depending on tile load condition. *( ) : 127V/60Hz, t t0~115V/60Hz, 115V/60HzRating ONLY.

*< >: TAIBEI

1. When power is initially applied or reapplied after power cut, "Medium" is automatically selected.

2. When the temperature selection switch in the freezer and refrigerator compartments is pressed, the light is on in the

following sequence:

"Medium" ,"Medium Max" , "Max" .'"Min" , "Medium Min" , "Medium"

3. The temperature setting condition of freezer and refrigerator compartments shall not be indicate in the standard model

(GRIP247, GRIP207, GR_L247, GR-L207, GR-C247, GR_C207, GR-B247, GR-B207) when refrigerator or home bar

door is closed.

- 25-

Dieses Handbuch passt für folgende Modelle

Andere LG Kühlschrank Handbücher

LG MFL67229857 Bedienungsanleitung

LG GM5148AERV Bedienungsanleitung

LG Refrigerator-freezer Bedienungsanleitung

LG GN-U232S Bedienungsanleitung

LG LDC22370 Series Bedienungsanleitung

LG GR-L207WVS Bedienungsanleitung

LG LMXS27626 Series Bedienungsanleitung

LG LSC23924 Series Bedienungsanleitung

LG LFCS25663 series Bedienungsanleitung

LG LRMXC2206 Series Bedienungsanleitung

LG LRSC 26910SW Bedienungsanleitung

LG REFRIGERATOR Bedienungsanleitung

LG GR-A702HLHU Bedienungsanleitung

LG LRBNC1104S.ASTCNA0 Bedienungsanleitung

LG GR-389SVQF Bedienungsanleitung

LG LSC27921 Series Bedienungsanleitung

LG GP-5D906BSL Bedienungsanleitung

LG GNM-732HWL Bedienungsanleitung

LG GR-379GTCA Bedienungsanleitung

LG LSC26905 Series Bedienungsanleitung

LG GC-051SW Bedienungsanleitung

LG GN-U291SC Bedienungsanleitung

LG GR-M352YVQ Bedienungsanleitung

LG lfxs24623 series Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung