LG LRSPC2331NI Bedienungsanleitung

PARTS IDENTIFICATION

3. Ref No. : GR-L247ER, GR-L207ER

Frame Displa

I¢

Dispenser Button

Cover Hinge Cover PWB

I'-'=

Water Tube

Freezer Refrigerator

Compartment Compartment

Shelf

ice maker

Lam (optional)

I Box

Shelf.

(Steel,

T/Glass)

Drawer -

or Shelf

(optional)

Guide bottle

Shelf

Door rack

LowerCover Conversion Switch

(MeatsNegetables) Humidity Switch

drawer/Meat drawer

-14-

HOW TO INSTALL REFRIGERATOR

!. How to Adjust Door Height of Refrigerator

• Make the refrigerator level first. (If the refrigerator isnot installed onthe flatfloor, the height of freezer and refrigerator

door may not be the same.)

1. If the height of freezer dOOr is lower than that of

refrigerator compartment : 2. If the height of freezer door is higher than that of

refrigerator compartment :

Insert addver _ into the groove _ of adjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

Insert adriver _into the groove _ of adjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

-18-

HOW TO INSTALL REFRIGERATOR

2. How to Install Water Pipe

•Before Installation

1. The icemaker requires the water pressure of 1.5 -

8.5kgf/cm 2. (It is acceptable if city water fills a cup of

180cc with water for 3 seconds)

2. Install booster pump where the city water pressure is

below 1.5kgf/cm2 for normal operation of water and ice

dispenser.

3. The total length of water pipe shall be less than 12m. Do

not bend the pipe at right angle. If the length is more

than 12m, there will be troubles on water sepply due to

water pressure drop.

4. Please install water pipe where there is no heat around.

2-1. When connecting directly to the water tap.

•Please confirm the following installation parts.

Valve Feed Rubber, Packing Connector. Pipe

(_ Co_nnector, Pipe Tape, Teflon

Class.

Conve-

rtible

iWater

Valve

Water

Conn-

ector

Shape and Spec.

Connector, (MECH) Pipe

Nomenclature

Valve Feed

PINe Remarks

5221JA3001A Common Use

NoHoles

4932JA3003A

6631JA3004A

6631JA3004B

3920JA3001B

6631JA3004C No Holes

6631JA3004D

3920JA3001A

4932JA3003C

6631JA3004E No Holes

6631JA3004F

3920JA3001C

No Holes

Connector,(MECH)Pipe

ConversionConnector(3/4")

BalanceCon_%lor(3/4")

Packing(e24x3t)

4932JA3003B

ConversionConnectorON25)

BalanceConectoor(W25)

Packing(o23x3t)

Connector,(MECH)Pipe

ConversionConnector(W28)

BalanceConector(W28)

Pesking(o26x3t)

Connector,(MECH)Pipe

conversion Connector(l/2")

BalanceConector(1/Z')

Pesking(e19x3t)

4932JA3003D

6631JA3004G

6631JA3004H

3920JA3001D

-19-

HOW TO INSTALL REFRIGERATOR

1. Connection of Pipe Connector A and B.

1) Turn off main valve of water pipe.

2) Disconnect water lap from piping by loosening nuts.

3) Connect pipe connector Aand B to piping after sealing

the pipe connector with sealing tapes.

4) Connect feed valve to pipe connector A.

5) If there is only one tap water pipe, connect pipe

connector Aonly and install feed pipe.

Caution : • Feed pipe should be connected to cold water

line. If it is connected to hot water line, trouble

may occur.

•Please check rubber packing when connecting

feed pipe.

Pipe Connector B Feed

How to wind

Sealing Tapes.

Single Lever Type Faucet

(general)

Two Hands Type Faucet

Feed

Valve

General Type

Single Lever Type Faucet (one

hole, tech type and hand spray)

Feed

Valve

2. Water Supply

1) After the installation of feed water, plug the refrigerator

to the earthered wall outlet, press the water dispenser

button for 2 -3 minutes, and confirm that the water

comes out.

2) Check leakage at connecting part, then arrange water

tube and locate the refhgerater at its regular place if

there is no leaking.

WaterTube

-- Water Tube

- 20 -

HOW TO INSTALL REFRIGERATOR

3, When customer uses bottled water,

*If customer wants to use bottled water, extra pump should be installed as shown below.

1. The pump system should not be on the floor (it may cause noise and vibration). Securety fasten the inlet and outlet

nuts of pump.

2. If there is any leakage alter installation, cut the water tube at right angle and reassemble.

3. When put the water tube end into the bottle, leave a clearance between bottle bottom and water tube end.

4 Check water coming out and any leakage.

Caution : • If feed tube is more than 4m, less water will come out due to pressure drops.

•Use standard feed tube to prevent leaking.

f" N

• Outternal Filter

t. Filter Fixation

1) Connect feed tube to the filter outlet and water valve connecting tube,

2) Fix the filter at proper place around the sink where it is easy to replace the filter and to receive the cleaning water,

Please consider the length of tube shall be less than 12m when locating filter.

3) When fixing the filter, use fixing plate and cable depending on the surrounding conditions.

FixingCable_

FixingPlate FixingPlate

• "J

2. Filter Cleaning

t) Connect feed tube to the inlet of feed valve end filter.

2) Clean the main valve and feed valve with water for at

least one minute until clean water comes out.

-21 -

Hot Water

Cold Water

Filter Inlet

Filter_

Water

HOW TO INSTALL REFRIGERATOR

•Install Water Filter (Applicable to some models only)

•Before Installing water filter

1. Before installing the filter, take out the top shelf of the

refrigerator after tilting it to the direction (O) and liRing it

to the direction ((_)) and move it to the lower part.

2. Remove the lamp cover by pressing the protrusion

under the cover and pulling the cover to the front.

Control box

guideline

and the fastening indication line

Control box

•Installing water filter

t. Initial installation of water filter

Remove the filter substitute cap by turning it

counterclockwise (O) by 90 degrees and pulling itdown.

Note : Keep it safe to use it later when you do not use the

filter.

Remove the red cap from the filter and attach the

sticker. Insert the upper part of the filter (_)) after

aligning with the guideline marked on the control box,

and fasten it by turning it clockwise by 90 degrees.

Note : Check that the guideline and the fastening

indication line are aligned.

2. Replacement of water filter

While holding the lower part of the filter, turn it

countemlockwise (O) by 90 degrees and pull itdown.

Note : Check that the guideline and the loosening

indication line are aligned.

and the loosening indication line

•After installing water filter

Reassemble the lamp cover and the top shelf of the

refrigerator. To place the top shelf of the refrigerator, raise

the front part of the shelf abit so that the hook of the shelf

is fit into the groove,

In order to clean the water filter system, drain water for

about 3 min.

Note : Then open the door of the refrigerator and check for

water droppings on the shelf under the filter.

-22 -

HOW TO INSTALL REFRIGERATOR

3. How to Control the Amount of Water Supplied to Icemaker.

3-1. Confirm the amount of water supplied to the icemaker.

1, Pull out the ice bank in the upper part of the freezer compartment,

Caution : * Do not put hands or tools into the chute to confirm

the operation of geared motor.

it may damage refrigerator or hurt hands.)

•Check the operation of motor with its operation

noise,

2. Apply electricity after connecting water pipe.

1) Press test switch under the icemaker for two seconds as shown below.

2) The bell rings(ding-dong) and ice tray rotates and water comes out from the icernaker water tube.

3) The water shall be supplied two or three times into the tray, The amount of water supplied for each time is small,

Put a water container under the ice tray and press test switch.

4) When ice tray rotates, the water in it will spill. Collect the spilt water and throw away intothe sink.

5) When ice tray has finished rotation, water comes out from the water tube. Confirm the amounts of water in the ice tray.

(refer to fig. The optimum amount of water is 110ec)

*It is acceptable if the adjusted level of water is a bit smaller than optimum level.

- 23 -

HOW TO INSTALL REFRIGERATOR

3-2o Control the amount of water supplied to the

icemaker.

Caution : • Please unplug the power cord from the wall

outlet and wait for more than three minutes

before disconnecting PWB cover as 310V is

applied in the control panel

1. Disconnect PWB cover from the upper part of the

refrigerator.

(+) Driver

2. Adjust the amount of water supplied by using DIP

switch.

• Water Supplying Time Control C ,tion

SWITCH NO Water Suppling

S/W1 S/W2 S/W3 Time

OFF OFF OFF 6.5 Sec.

ON OFF OFF 5.5 Sac,

OFF ON OFF 6 Sec.

ON ON OFF 7 Sec.

OFF OFF ON 7.5 Sec.

ON OFF ON 8 Sec.

OFF ON ON 9 Sac.

ON ON ON 10 Sec.

1) The water supplying time is set at five seconds when the

refrigerator is delivered.

2) The amount of water supplied depends on the setting

time and water pressure (city water pressure).

3) If ice cube is too small, increase the water supplying

time. This happens when too small water is supplied into

the ice tray.

4) If ice cube sticks together, decrease the water supplying

time. This happens when too much water is supplied

into the ice tray.

Caution : When adjusting the amount of water supplied,

adjust step by step. Otherwise the water may

spill over.

3. When adjustment of control switch for the amount of

water supplied is complete, check the level of water in

the ice tray.

Confirm the amount

of water

"-.\_'_I_ OpSmum level)

• s S

-24 -

MICOM FUNCTION

l. Monitor Panel

1-1. GR-P247, GR-P207, GR-L247, GR-L207 1-2. GR-C247, GR-C207, GR-B247, GR-B207

Function Monitor

tt'l

======

Freezer compartment Refngerator compartment Dispenser se_ec_cabuttO:l

temperature control Button temperatsre control Button

2. Description of Function

2-1. Funnction of Temperature Selection

Division

Changeof

IndicationLamp

Power Initially On 1st Press 2nd Press 3th Press 4th Press

........ .... '== , ._ . _ _ _. _ I _ == _'-- ._ __ __

--, ...... .__ __,__

i m m i i*qm. i m * mm t _ _ i_ _ i

m--. __,rap

@@ @@ @@

Temperature

Control Medium Medium Max Max Min Medium Min

Freezer -19 °C -22 °C -23 °C

Control (-18 °C) (-20.5 °C) (-22 °C) -15 °C -17 °C

<-19 °C> <-20.5 °C> <-22 °C> <-16.5 =C> <-18 °C>

Refrigeration 6 "C

Control 3 °C 1,5 °C 0=C (7 °C) 4.5 =C

<2 °C> <1 °C> <0 °C> <4,5 °C> <3 °C>

* The tenqmrature can val_yt-3°C depending on the toadcondition. *( "1: 127Vi60|lz, 110_115V,"60[lz. 115Vi60Hz RatingONLY.

*< >:TAIBEI

1. When power is initially applied or reapplied after power cut, "Medium" is automatically selected.

2. When the temperature selection switch in the freezer and refrigerator compartments is pressed, the light is on in the

following sequence:

"Medium" -* "Medium Max" -* "Max" --, "Min" --, "Medium Min" -, "Medium"

3. The temperature setting condition of freezer and refrigerator compartments shall not be indicate in the standard model

(GR-P247, GR-P207, GR-L247, GR-L207, GR-C247, GR-C207, GR-B247, GR-B207) when refrigerator or home bar

door is closed,

-25 -

MICOM FUNCTION

2-2. Automatic ice maker

-The automatic ice maker can automatically make 8 pieces of ice cube at atime, 80 pieces a day. But these quantities may

be varied according to various conditions including how many times the refdgerator door opens and closes.

•Ice making stops when the ice storage bin is full.

• if you don't want to use automatic ice-maker, change the ice-maker switch to ON-OFF.

If you want to use automatic ice-maker again, change the switch to OFF-ON.

NOTE : It is normal that a noise is produced when ice made is dropped into the ice storage bin.

2-3. When ice maker does not operate smoothly

Ice is lumped together

•When ice is lumped together, take the ice lumps out of the ice storage bin, break them into small pieces, and then place

them into the ice storage bin again.

-When the ice maker produces too small or lumped together ice, the amount of water supplied to the ice maker need to

adjusted. Contact the service center.

:,_If ice is not used frequently, it may lump together.

Power failure

•Ice may drop into the freezer compartment. Take the ice storage bin out and discard all the ice then dry it and place it

back. After the machine is powered again, crushed ice will be automatically selected.

The unit is newly installed

• It takes about 12 hours for a newly installed rethgerator to make ice in the freezer compartment.

- 26 -

Dieses Handbuch passt für folgende Modelle

Andere LG Kühlschrank Handbücher

LG LFC21776 Series Bedienungsanleitung

LG LSMX211ST Bedienungsanleitung

LG GC-151SNA Bedienungsanleitung

LG LSC27914SB Bedienungsanleitung

LG GR-M352RLC Bedienungsanleitung

LG LSC27910SW/01 Bedienungsanleitung

LG LB Series Bedienungsanleitung

LG LS25HVLVLV Bedienungsanleitung

LG LSC26905 Series Bedienungsanleitung

LG GR-B197GVQ Bedienungsanleitung

LG LMX25964SS Benutzerhandbuch

LG LFXS26596 series Bedienungsanleitung

LG SXS Refrigerator Bedienungsanleitung

LG GR-W600GS Bedienungsanleitung

LG G 201 Series Bedienungsanleitung

LG GN-D702HLAM Bedienungsanleitung

LG LMX25986SB Bedienungsanleitung

LG GWB207FBQA Bedienungsanleitung

LG GSJ960MCCZ Bedienungsanleitung

LG GC-B459SMUM Bedienungsanleitung

LG LMX25988SB Bedienungsanleitung

LG GT28WPP Bedienungsanleitung

LG LFC20770SB Bedienungsanleitung

LG LFX28968 Series Handbuch

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung