LG LSC27910 Series Bedienungsanleitung

REFRIGERATOR

REFRIGERADOR

LSC27910**

Owner´s Manual

24 HOURS A DAY, 7 DAYS A WEEK FOR LG CUSTOMER SERVICE

para el servicio LG (Atención al Cliente) 24 horas al día, 7 días a la semana

website: http://us.lge.com

1-800-243-0000

Entry

Important Safety Instruction

Identification of Parts

Where to Install

Door Removal

Door Replacement

Water Pipe Installation

Water Connection Instruction Guide

Operation Instruction Guide

Height Adjustment

Starting

Adjusting the Temperatures and functions

(Dispenser/Automatic Icemaker)

Shelf

Location of Foods

Storing Foods

How to Dismantle Parts

General Information

Cleaning

Troubleshooting

Table of Contents

Introduction

Installation

Operation

Suggestion on

Food Storage

Care and

Maintenance

Introduction

this guide as a permanent record of your purchase. Staple your receipt here.

Date of purchase :

Dealer

Dealer address

Dealer phone no.

Model no.

Serial no.

Important safety

Instructions

WARNING

CAUTION

You can be killed or seriously injured if you don’t follow instructions.

Indicates an imminently hazardous situation which, if not avoided,

may result in minor or moderate injury, or product damage only.

All safety messages will identify the hazard, tell you how to reduce the chance of injury

and tell you what can happed if the instructions are not followed.

DANGER You will be killed or seriously injured if you don’t follow instructions.

This guide contains many important safety messages. Always read and obey

SAFETY MESSAGES

To reduce the risk of fire, electric shock or injury to persons when using your

product, basic safety precautions should be followed, including the

following. Read all instructions before using this appliance:

NEVER unplug your refrigerator by pulling on the power cord. Always grip the

plug firmly and pull it straight out from the outlet.

Repair or replace inmediately all electric service cords that have become frayed

or otherwise damaged. Do not use a cord that shows cracks or abrasion damage

along its length or at either the plug or connector end.

When moving your refrigerator away from the wall, be careful not to roll over or

damage it in any way.

Do not crush or damage the water line.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance.

Do not allow children to climb, stand, or hang on the refrigerator doors or

shelves in refrigerator. They could damage the refrigerator and seriously injure

themshelves.

Keep fingers out of “pinch point” areas; clearances between the doors and

cabinet are necessarily small. Be careful when you open the doors when children

Unplug your refrigerator before cleaning or making any repairs.

NOTE: We strongly recommend that any servicing be performed by a qualified

individual.

Entry

The model and serial numbers are found on the inner case or back of refrigerator

compartment of this unit. These numbers are unique to this unit and not

available to others. You should record requested information here and retain

are in the area.

If you are getting rid of your old refrigerator, please follow

the instructions at right to help prevent accidents.

Introduction

IMPORTANT: Please read carefully

TO CONNECT ELECTRICITY

GROUNDING

REQUIREMENTS

Shock Hazard

Electrical

FOR PERSONAL SAFETY, this appliance must be

properly grounded. Have the wall outlet and the

circuit checked by a qualified electrician to make sure

the outlet is properly grounded.

Ensure proper

ground exists

before use.

3-prong

grounding

plug

3-prong

grounding type

wall receptacle

WARNING

RECOMMENDED GROUNDING METHOD

The refrigerator should always be plugged into its own individual properly

grounded electrical outlet rated for 115 Volts, 60 Hz, AC only and fused at 15 or 20

amperes. This provides the best performance and also prevents overloading house

wiring circuits which could cause a fire hazard from overheated wires. It is

recommended that a separate circuit serving only this appliance be provided.

Use a receptacle which cannot be turned off with a switch or pull chain. Do not use

an extension cord.

Where a standard two-prong wall outlet is encountered, it is your personal

responsibility and obligation to have it replaced with a properly grounded three-

prong wall outlet.

Do not, under any circumstances, cut or remove the third (ground) prong from the

power cord.

NOTE: Before performing any type of installation, cleaning, or removing a light

bulb, turn the control (Thermostat, Refrigerator Control or Freezer Control,

depending on the model) to OFF and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the refrigerator to the electrical

source and reset the control (Thermostat, Refrigerator Control or Freezer Control,

depending on the model) to the desired setting.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly

recommend against the use of an extension cord. However, if you still elect to use

an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States), 3-wire grounding type appliance extension cord having a groundind type

plug and outlet, and that the electrical rating of the cord be 15 amperes (minimum)

and 120 volts.

Use of an extension cord will increase the clearance needed for the back of the

refrigerator.

If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualified person in order to avoid any hazard.

Introduction

Freezer

Compartment Refrigerator

Compartment

Dairy Corner

Water Filter

Lamp 1 or 2

Door Rack

Lamp

Automatic

Icemaker

Shelf (steel)

Door Rack

Drawer

Door Rack

Lower Cover

Shelf

Snack Drawer

Vegetable Drawer

Door Rack

IdentiﬁcationofParts

•

If you nd some parts missing from your unit,

they may be parts only used in other models.

Where to install

Unstable installation may cause vibration and

noise. If the oor to install the refrigerator on

is not even, make the refrigerator level by

rotating the height adjusting screw. Carpet

or oor covering on which a refrigerator is

installed may be discolored by heat from the

bottom of the refrigerator.

If our refrigerator causes this kind of

damage, there is something wrong with it.

Customers will not stand for this.

Strong

and even ﬂoor

A proper

distance from

adjacent items

Please keep the refrigerator at a proper

distance from other things. Too small a

distance from adjacent items may result in

lowered freezing capability and increased

electricity consumption charges .

1”(2.54 cm )

Installation

Where water

supply can be

easily connected

in a dry place

Where it is free

from heat

Select a place where a water supply can be

easily connected between the automatic ice

maker and dispenser.

Installing the refrigerator in a wet or damp

area may cause rust and may be an electrical

hazard.

If this refrigerator is installed where the

ambient temperature is high, the freezing

capacity is deteriorated and the cost of

electricity used increases.

•

Install the refrigerator at a place where the ambient temperature is 5˚C ~ 43˚C

(41˚F~110˚F).

Ambient temperature outside this range may cause product malfunction. Also, the

tube between the dispenser and automatic ice maker may freeze.

NOTE

Bottom Pad

Tools Required

Door removal

Failure to do so could result in death or serious injury.

If your entrance door is too narrow for the

refrigerator to pass through, remove the

refrigerator door and pass the refrigerator laterally.

Electric Shock Hazard

Disconnect electrical supply to refrigerator before installing.

Remove the lower cover by lifting upward, and

then pull up the water feed tube while pressing

area



shown in the figure to the right.

Remove Lower

Cover and

Water Feed Tube

Warning

Remove the

Freezer

Compartment

Door

Remove the

Refrigerator

Door

Installation

1) Remove the hinge cover by loosening the

screws. Disconnect all connections except

the ground line.

2) Remove the keeper by rotating it counter

clockwise



and then lifting the upper

hinge up

.

3) Remove the freezer compartment door by

lifting it upward. This time, the door should

be lifted enough for the water feed tube to

be completely pulled out.

1) Loosen the hinge cover screws and remove

the cover. Remove connection wire.

2) Remove keeper by rotating it clockwise



and then remove the upper hinge by lifting

it up



3) Remove the refrigerator compartment door

by lifting it up.

•

If a tube end is deformed or abraded, trim the part away.

Disconnecting the tube under the door causes about 1.5 litters water to flow out. Please

put a large container at end of tube to prevent water from draining on to the floor.

NOTE

•

When removing the upper hinge, be careful that the door does not fall forward .

NOTE

•

After removing the door, take it into the kitchen where you are installing the

refrigerator. Lay it down on a blanket and be careful to avoid damaging the water

feed tube.

NOTE

Lower Cover

Lower hinge

Lower Hinge

Keeper

Water Feed Tube

Connection

Wires

Connection

Wires

Hinge

Cover

Upper Hinge

Keeper Upper Hinge

Earth Line

Feed water tube installation

Push the refrigerator sideways through the

entrance door as shown in the right picture.

Automatic icemaker operation needs water pressure of 21.3~121psi(lb/inch2) (That

is, a 7oz. paper cup will be ﬁlled within 3 sec.).

to purchase a separate pressure pump for normal automatic icemaking and cool

water feed.

Keep the total length of the water feed tube within 40 feet and be careful not to

bend or kink the tube. If the tube is longer than 40 feet, the icemaker and water

dispenser will not operate properly.

Install the water feed tube at a place free from heat.

Connect to potable water supply only.

Refer to instructions with water ﬁlter kit for installation.

Mount the doors in the reverse order of

removal after the refrigerator is brought to

the installation area.

Move the

Refrigerator

Before

Installation

Warning

Installation

Water Connection Instruction Guide

Read all directions carefully before you begin.

Connecting

the Refrigerator

to a Water Source

•

If operating the refrigerator before installing the water connection, turn icemaker

to the OFF position to prevent operation without water.

•

All installations must be in accordance with local plumbing code requirements.

•

Use copper tubing and check for leaks.

•

Install copper tubing only in areas where temperatures will remain above freezing.

•

It may take up to 24 hours for your icemaker to begin producing ice.

IMPORTANT

Standard screwdriver

7/16-inch and 1/2-inch open-end wrenches or two adjustable wrenches

1/4-inch nut driver

1/4-inch drill bit

Hand drill or electric drill (properly grounded)

Tools Required

NOTE

In order to perform the water connection you will need to buy: a 1/4-inch saddle-type

shut off valve, a union, and copper tubing. Before purchasing, make sure the saddle-type

valve complies with your local plumbing codes. Do not use a piercing-type or 3/16-inch

saddle valve which reduces water flow and clogs more easily.

Screwdriver

Adjustable wrenches

Electric drill

NOTE:

Check the direction of the lever hinge.

Correct Incorrect

If water pressure does not reach the rated 21.3psi(lb/inc ) or below, it is necessaryh

Door replacement

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn on the nearest faucet to relieve the pressure on the

line. It may help to open an outside faucet to allow the water to drain from the line in

the house.

3. Find a 1/2-inch to 1-1/4-inch vertical COLD water pipe near the refrigerator.

Connect

the Tubing to

Water Line

•

Horizontal pipe will work, but the following precaution must be taken: Drill on the top of the pipe

not the bottom. This will help keep water away from the drill. This also keeps normal sediment

from collecting in the valve.

NOTE

4. To determine the length of copper tubing you will need, measure from the connection

on the lower left rear of the refrigerator to the water pipe. Add 7 feet (2.1m) to allow

for moving refrigerator for cleaning. Use 1/4-inch O.D. (outside diameter) copper

tubing. Be sure both ends of copper tubing are cut square.

5. Using a drill, drill a 1/4-inch hole in the cold water pipe you have selected.

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly

in the 1/4-inch drilled hole in the water pipe and that the washer is under the pipe

clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so

washer makes a watertight seal. Do not overtighten or you may crush the cooper

tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect

copper tubing.

7. Slip compression sleeve and compression nut on copper tubing as shown. Insert end

of tubing into outlet end squarely as far as it will go. Screw compression nut onto

outlet end with adjustable wrench. Do not over tighten.

8. Place the free end of the tubing into a container or zinc, and turn ON main water

supply and flush out tubing until water is clear. Turn OFF shutoff valve on the water

pipe. Coil the copper tubing as shown below.

Cold Water Pipe

Pipe Clamp

Coil of Polyethylene or

Copper Tubing

Compression Nut

Compression Sleeve

Shut Off Valve

Packing Nut

Installation

Coil of Polyethylene or

1/4" Cooper Tubing

Tubing Clamp

1/4"

Compression

Nut

Ferrule

(sleeve)

Refrigerator Connection

Operation Instruction Guide

Before making the connection to the refrigerator, be sure the refrigerator

power cord is not plugged into the wall outlet.

• If your refrigerator does not

have a water filter, we

recommend installing one. If

your water supply has sand or

particles that could clog the

screen of the refrigerator’s

water valve. Install the filter in

the water line near the

refrigerator.

1. Remove the plastic flexible

cap from the water valve.

2. Place the compression nut and

ferrule (sleeve) onto the end of

the tubing as shown.

3. Insert the end of the copper tubing into the connection as far as possible. While

holding the tubing, tighten the fitting.

Connect the Tubing

to the Refrigerator

Andere Handbücher für LSC27910 Series

Inhaltsverzeichnis

Andere LG Kühlschrank Handbücher

LG LSC21943 Bedienungsanleitung

LG GRL1960TQA Bedienungsanleitung

LG GR-J387CVBL Bedienungsanleitung

LG GM-589 Series Bedienungsanleitung

LG GR-5D725SL Bedienungsanleitung

LG GR-J910SDID Bedienungsanleitung

LG G C702S Series Bedienungsanleitung

LG LFC25776ST Benutzerhandbuch

LG GC-X257CQES Bedienungsanleitung

LG LFXS26973D Bedienungsanleitung

LG REFRIGERATOR Bedienungsanleitung

LG GR-R491JCA Bedienungsanleitung

LG Refrigerator-freezer Bedienungsanleitung

LG GR-R463JCA Bedienungsanleitung

LG GSLV31MCXM Bedienungsanleitung

LG GR-M31FWCHL Bedienungsanleitung

LG LBC20514TT - Titanium 19.7 cu. ft. Bottom Freezer Refrigerator... Bedienungsanleitung

LG GF-AD910SL Bedienungsanleitung

LG LFX25991ST Benutzerhandbuch

LG LRBN2051 Series Bedienungsanleitung

LG GR-M352RLC Bedienungsanleitung

LG LMX25964SS Benutzerhandbuch

LG LFX23961SW /01 Bedienungsanleitung

LG GR-V292RLC Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung