LG SxS LRSPC2661T Bedienungsanleitung

WARNINGS AND PRECAUTIONS FOR SAFETY

Please observe the following safety precautions in order to

use safely and correctly the refrigerator and to prevent

accident and danger during repair.

1. Be care of an electric shock. Disconnect power cord

from wall outlet and wait for more than three minutes

before replacing PWB parts. Shut off the power

whenever replacing and repairing electde components.

2. When connecting power cord, please wait for more than

five minutes after power cord was disconnected from the

wall outlet.

3. Please check if the power plug is pressed down by the

refrigerator against the wall tf the power plug was

damaged, it may cause fire or electric shock.

4. ff the wall outlet is over loaded, it may cause fire. Please

use its own individual electrical outlet for the refrigerator.

5. Please make sure theoutletispropedy earthed,

particularlyin wet or damp area.

6, Use standard electrical components when replacing

them.

7. Make sure the hook is correctly engaged.

Remove dust and foreign matedals from the housing

and connecting parts.

8. Do notfray. damage, machine, heavily bend, pullout,

or twist the power cord.

Please check the evidence of moisture intrusion in the

electrical components. Replace the parts or mask it

with insulation tapes if moisture intrusion was

confirmed.

10. Do not touch the icomaker with hands or tools to

confirm the operation of geared motor.

11. Do not let the customers repair, disassemble, and

reconst_ct the refdgerator for themselves. It may

cause accident, electTic shock, or fire.

12. Do not store flammable materials such as ether,

benzene, alcohol, chemicals, gas, or medicine in the

refrigerator.

13. Do not put flower vase, cup, cosmetics, chemicals,

etc., or container with full of water on the top of the

refrigerator.

14. Do not put glass bottles with full of water into the

freezer. The contents shall freeze and break the glass

bottles.

15. When you scrap the refrigerator, please disconnect the

door gasket first and scrap it where children are not

accessible.

-3-

SPECIFICATIONS

ITEMS

DIMENSIONS (ram)

NET WEIGHT (kg)

COOLING SYSTEM

TEMPERATURE CONTROL

DEFROSTING SYSTEM

SPECIFICATIONS

960(W)x915(D)×1795(H)

169

Fan Cooling

MicomControl

FullAutomatic

Heater Defrost

Cyclo-Pentane

P,T.C,Starting Type

Fin Tube Type

Wire Condenser

R134a (210g)

FREOL @15G (330 cc)

1_0.83

MOLECULAR SIEVE XH-7

ITEMS

FIRST DEFROST

DEFROST CYCLE

DEFROSTING DEVICE

INSULATION

COMPRESSOR

EVAPORATOR

CONDENSER

REFRIGERANT

LUBRICATING OIL

DRIER

CAPILLARY TUBE

ANTI SWEAT HEATER

ANTI-FREEZING HEATER

FREEZER LAMP

REFRIGERATOR LOWER LAMP

REFRIGERATOR UPPER LAMP

DISPENSER LAMP

1072

SPECIFICATIONS

5-6 Hours

13- 15 Hours

Heater, Sheeth-AL

Heater, Sheatb-ML

Heater, Drain

DispenserDuct Door Heater

DispenserHeater

Frame LCD Heater

Chilled Room DuctHeater

Damper Heater

Tube Inject Heater

60W (1 EA)

30W (2 EA)

i15W(1 EA)

-4-

PARTS IDENTIFICATION

Manag

Reset S/W Cover PWB

Frame

Display

Lamp

Ice &Water

Dispenser

Button

RemoteControl

Receiver

Camera

Banklce

Control Box, R

Dairy Corner

Cover, Lamp-R(U)

Cantilever Shelf

Cover,

Shelf-F

Supporter

Basket

Cover Lower

Adjust Screw

(left)

Egg Box

Snack Comer

Slide Out

Cantilever Shelf

Cover

Guide Bottle

Cover, Lamp-R(L)

FruiUVegetable

Drawer

Bottle

AdjustScrew

(right)

Vegetable/Chilled Drawer

Convertible Switch

*Optional Part

.5-

HOW TO INSTALL REFRIGERATOR

1. How to Adjust Door Height of Refrigerator

•Make the refrigerator level first. (ff the refrigerator is not installed on the fiat floor, the height of freezer and refrigerator

door may not be the same.)

1. If the height of freezer door is lower than that of

refrigerator compartment : 2. If the height of freezer door is higher than that of

refrigerator compartment :

Insert a driver B into the groove A of edjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

Insert a ddver B into the groove A of adjusting screw

and rotate driver in arrow direction (clockwise) until the

refrigerator becomes horizontal.

-6-

HOW TO INSTALL REFRIGERATOR

2. How to Install Water Pipe

•Before Installation

t. The icemaker requires the water pressure of 1.5 -

8.5kgf/cm 2.(It is acceptable if city water fills a cup of

180cc with water for 10 seconds)

2. Install booster pump where the city water pressure is

below 1.5kgf/cr_- for normal operation of water and ice

dispenser.

3. The total length of water pipe shall be less than 12rn. Do

not bend the pipe at right angle. If the length is more

than 12m. there will be troubles on water supply due to

water pressure drop.

4. Please install water pipe where there is no heat around.

5. Be sure that the filter does not sterilize.

6. The life span of water filter depends on the use

conditions. But the filter is generally replaced in every

six months. Install filter where replacement can be easily

performed,

2-1. When connecting directly to the water tap.

•Please confirm the following installation parts.

Valve Feed Rubber, Packing Connector, Pipe

Connector, Pipe Tape, Teflon

Class. Shape and Spec. Nomenclature PINo Remarks

Conve- _.[_"_ Valve Feed 5221JA3001A Common Use

rtible

Water

Valve

Water _ Q 4932JA3003A

Conn- _____ 6631JA3004A No Holes

ector 6631JA3004B

3920JA3001 B

Connector, (MECH)Pipe No Holes

Connector,(MECH)Pipe

ConversionConnector(3/4")

BalanceConector(3/4")

Packing(o24x3t)

Connector,(MECH) Pipe

ConversionCeenector(W25)

BalanceConectcor(W25)

Packing(a23x3t)

Connector,(MECH)Pipe

ConversionConnector(W28)

BalanceConector(W28)

Packing(e26x3t)

Connector,(MECH)Pipe

ConversionConnector(I/2")

BalanceConector(1/2")

Packing(ol9x3t)

4932JA3003B

6631JA3004C

6631JA3004D

3920JA3001A

4932JA3(X)3C

6631JA3004E No Holes

6631JA3004F

3920JA3001C

No Holes

4932JA3003D

6631JA3004G

6631JA3004H

3920JA3001D

-7-

HOW TO INSTALL REFRIGERATOR

2-2. Connection of Pipe Connector A and B.

1) Turn off main valve of water pipe.

2) Disconnect water tap from piping by loosening nuts.

3) Connect pipe connector A and B to piping alter sealing

the pipe connector with sealing tapes.

4) Connect feed valve to pipe connector A.

5) If there isonly one tap water pipe, connect pipe

connector A only and install feed pipe.

Caution : oFeed pipe should be connected to cold water

line. If it is connected to hot water line, trouble

may occur.

• Please check rubber packing when connecting

feed pipe.

Pipe Connector B Feed

How towind

SealingTapes.

Single Lever Type Faucet

(general)

Two Hands Type Faucet

Feed

Valve

Gene_lType

Feed

Valve

Single LeverTypeFaucet(one

hole, techtypeand hand spray)

Valve

2-3. Water Supply

1) After the installation of feed water, plug the refrigerator

to the earthered wall outlet, press the water dispenser

button for 2- 3 minutes, and confirm that the water

comes out.

2) Check leakage at connecting part, then arrange water

tube and locate the refrigerator at its regular place if

there is no leaking.

-8-

HOW TO INSTALL REFRIGERATOR

•Install Water Filter (Applicable to some models only)

•Before Installing water filter

1. Before installing the filter, take out the top shelf of the

refrigerator after tilting it to the direction (a) and lifting it

to the direction (b) and move it to the lower part.

2. Remove the lamp cover by pressing the protrusion

under the cover and pufiing the cover to the front.

•Installing water filter

1. Initial installation of water filter

Remove the filter substitute cap by turning it

counterclockwise (a) by 90 degrees and pulling it down.

Note : Keep it safe to use it later when you do not use the

filter.

Remove the red cap from the filter and attach the

sticker, Insert the upper part of the filter (a) after

aligning with the guideline marked on the control box,

and fasten it by turning it clockwise by 90 degrees.

Note : Check that the guideline and the fastening

indication line are aligned.

_ubstitute

_=_= Adhesion

_ _icker

2. Replacement of water filter

While holding the lower part of the filter, turn it

counterclockwise (a) by 90 degrees and pull it down.

Note : Check that the guideline and the loosening

indication line are aligned.

Control box

guide line

and the fastening indication line

O_i ;ontrolbox

"" " the guideline

andthe loosening indication line

•After installing water filter

Reassemble the lamp cover and the top shelf of the

refrigerator. To place the top sheff of the refrigerator, raise

the front part of the shelf a bit so that the hook ofthe shelf

is fit into the groove.

In order to clean the water filter system, drain water for

about 3 min.

Note : Then open the door of the refrigerator and check for

water droppings on the shelf under the filter.

-9-

HOW TO INSTALL REFRIGERATOR

3. How to Control the Amount of Water Supplied to icemaker.

3-1. Confirm the amount of water supplied to the icemaker.

t. Pullout the ice bank in the upper pert of the freezer compartment.

Caution : * Do not put hands or tools into the chute to

confirm the operation of geared motor.

it may damage refrigerator or hurt hands.)

•Check the operation of motor with its

operation noise.

2. Apply electricity after connecting water pipe.

1) Press test switch under the icemaker for two seconds as shown below.

2) The bell rings(ding-dong) and ice tray rotates and water comes out from the icemaker water tube.

3) The water shall be supplied two or three times into the tray. The amount of water supplied for each time is small

Put a water container under the ice tray and press test switch.

4) When ice tray rotates, the water in it will spill. Collect the spilt water and throw away into the sink.

5) When ice tray has finished rotation, water comes out from the water tube. Confirm the amounts of water in the ice tray.

(refer to fig. The optimum amount of water is 110cc)

Confirm the amount

of water

Test Switch

Ice maker

i '

*It is acceptableiftheadjusted levelof water isa bit smaller than optimumlevel.

-10-

HOW TO INSTALL REFRIGERATOR

3-2. Control the amount of water supplied to the

icemaker.

Caution : •Please unplugthe powercordfrom thewall

outletand waitfor more thanthree minutes

before disconnectingPWS coveras 310V is

appliedin thecontrolpanel,

1. Disconnect PWB cover from the upper part of the

refrigerator.

j(+) Driver

Caution : When adjusting the amount of water supplied,

adjust step by step. Otherwise the water may

spill over.

Switch ON

Switch OFF

PWB(PCB), Assembly

3. When adjustment of control switch for the amount of

water supplied is complete, check the level of water in

the ice tray.

2, Adjust theamountof water suppliedby usingDIP

switch.

Confirm the amount

of water

• Water Supplying Time Control Option

SWITCH NO Water Suppling

S/W1 SNV2 S/W3 Time

OFF OFF OFF 6Sec.

ON OFF OFF 4 Sec.

OFF ON OFF 4.5 Sec.

ON ON OFF 5 Sec.

OFF OFF ON 5.5 Sec.

ON OFF ON 7Sec.

OFF .... ON ON ..... 8Sec.

ON ON ON gSec.

Optimumle ,"

"'_b_ _o_ SS

1) The water supplying time is set at five seconds when the

refrigerator is delivered.

2) The amount of water supplied depends on the setting

time and water pressure (city water pressure).

3) If ice cube is too small, increase the water supplying

time. This happens when too small water issupplied into

the ice tray. (eg: change 5 to 5.5 seconds)

4) If ice cube sticks together, decrease the water supplying

time. This happens when too much water is supplied

into the ice tray. (eg: change 5 to 4.5 seconds)

-11 -

ICEMAKERANDDISPENSEROPERATIONPRINCIPLEANDREPAIRMETHOD

2°4. Ice Ejection Control Function

1. This is to eject ice from ice maker cube mould after ice making is completed.

2. if Hall IC signal is on within 3.6 seconds after ice ejection motor rotates in normal direction, it does not proceed ice

ejection but waits, If the ice bank is full ice ejection motor rotates in normal direction in every hour to check the condition

of ice bank. If the ice bank is not full, the water supply control starts after completion of ice ejection control. If the ice bank

is full, ice ejection motor rotates in reverse direction and sops under ice making or waiting conditions.

3. if ice bank isnot full, ice ejection starts. The cube mould tilts to the maximum and ice is separated from the mould and ice

checking lever raises.

4. Ice ejection motor stops for 1 second if Hall IC signal changes from OFF (low) to ON (high) after 3.6 seconds when ice

ejecSon motor rotates in normal direction. If there is no change in Hall IC signals within 1 minute after ice e}ection motor

operates, ice ejection motor stops as ice ejection motor or hall IC is out of order.

5. If ice ejection motor or Hall IC is abnormal, ice ejection motor rotates in normal direction to exercise initial operation. It

resets the ice maker if ice ejection motor or Halt IC is normal.

6. The mould stops for 1 second at maximum tilted conditions.

7. The mould returns to horizontal conditions as ice ejection motor rotates in reverse direction.

8. When the mould becomes horizontal, the cycle starts to repeat:

Water Supply ..* Ice Making *Ice Ejection .._Mould Returns to Horizontal

r Bank is

HALL IC

OUTPUT

SIGNALS

Bank is "_

HALL IC

OUTPUT

SIGNALS

IICECHECKING

Maximum tilting

point

o ' ' =-)'/'

• , r

ii i

i1_ IIi

, ,,

OFF

ICECHECKING LEVEL 30° i I

i p / I i t

.... L.... J__J.

t t t i i

-8' O" 10" 32' 41" 53" 68" 80'

Lock Ice making Ice Checking

(o_n_ i:,_nt)

2±1 sec =I

9:_3 sec

I I

160" 170'

IceEjection Lock

8+-3sac IL

-22 -

Andere Handbücher für SxS LRSPC2661T

Inhaltsverzeichnis

Andere LG Kühlschrank Handbücher

LG GR-V202RV Bedienungsanleitung

LG LRTPC2031T precautio Bedienungsanleitung

LG GM-B208STS Bedienungsanleitung

LG LRSC 26910SW Bedienungsanleitung

LG GC-B419WLQA Bedienungsanleitung

LG LBC20514TT - Titanium 19.7 cu. ft. Bottom Freezer Refrigerator... Bedienungsanleitung

LG LFX28968SW Bedienungsanleitung

LG LFXS26972 Series Bedienungsanleitung

LG gr-392 Bedienungsanleitung

LG GT57BP K Series Bedienungsanleitung

LG GL-22 Series Bedienungsanleitung

LG SXS Refrigerator Bedienungsanleitung

LG LRFC21755 Series Bedienungsanleitung

LG GR-B197GVQ Bedienungsanleitung

LG GW-B227YLQK Bedienungsanleitung

LG LFX25973SW.ASWCNA0 Bedienungsanleitung

LG LTC22350 Series Bedienungsanleitung

LG GC-269VL.APZPEAL Bedienungsanleitung

LG LFX25974 Series Bedienungsanleitung

LG LLFGC2706 Series Bedienungsanleitung

LG GN-V232RL Bedienungsanleitung

LG GR-B24FWSHL Bedienungsanleitung

LG MFL68029533 Bedienungsanleitung

LG GR-391SCA Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung