LG PQRCVCL0Q Kurzanleitung

OWNER’S &

INSTALLATION MANUAL

SIMPLE WIRED REMOTE

CONTROLLER

Please read this manual carefully before operating

your set and retain it for future reference.

P/NO : MFL62862002 www.lg.com

Models : PQRCVCL0Q

PQRCVCL0QW

ENGLISH ITALIANO ESPAÑOL FRANCAIS DEUTSCH

PORTUGUESE

êìëëäàâ üáõä

2Wired Remote Controller

Simple Wired Remote Controller Ownerʼs & Installation Manual

TABLE OF CONTENTS

nSafety Precautions..................................................................3

nPart Description ......................................................................4

Simple Wired Remote Controller...............................................................4

nInstallation Instruction........................................................5~6

Group control..............................................................................................7

Installer setting – How to enter installer setting mode ...........................8

Installer setting – Test Run Mode .............................................................9

Installer setting – Setting Address of Central Control ..........................10

Installer setting – E.S.P ............................................................................11

Installer setting – Thermistor .................................................................12

Installer setting – Ceiling Height Selection ............................................13

Installer setting – Static Pressure Setting .............................................14

Installer setting – Remote Controller Master/Slave Setup....................15

Installer setting – Celsius/Fahrenheit .....................................................16

nOwners instruction ...............................................................17

Standard Operation – Cooling Mode ......................................................17

Standard Operation – Heating Mode.......................................................18

Standard Operation – Auto Operation Mode..........................................19

Standard Operation – Dehumidification Mode.......................................20

Standard Operation – Fan Mode .............................................................21

Function Setting – Fan Speed Selection ................................................22

Function Setting – Room temperature check ........................................23

Function Setting – Child Lock .................................................................24

Function Setting – Auto Swing................................................................25

Function Setting – Vane Angle Control ..................................................26

Different mode drive.................................................................................27

Checkups before reporting breakdown..................................................28

Safety Precaution

Ownerʼs & Installation Manual 3

ENGLISH

Be sure to request to the

service center or installation

specialty store when

installing products.

• It will cause fire or electric shock

or explosion or injury.

Request to the service center

or installation specialty store

when reinstalling the

installed product.

• It will cause fire or electric shock

or explosion or injury.

Do not disassemble, fix, and

modify products randomly.

• It will cause fire or electric shock.

Do not place flammable

stuffs close to the product.

• It will cause fire.

Do not allow water to run

into the product.

• It will cause electric shock or

breakdown.

Do not give the shock to the

product.

• It will cause breakdown when

giving the shock to the product.

nInstallation

Safety Precaution

• The installation requires expert skills, and it should be installed by the service center or other shops specialized

in the installation and recognized by our company.

• For all the problems arising after installation by someone who has no relevant qualifications, our company will

not provide free service.

• The following safety cautions are provided to prevent unexpected dangers or losses.

: If the user does not follow the mandatory items, it may result in serious injury or death.

: If the user does not follow the mandatory items, it may cause personal injury or property

damage.

: Warning and Caution are to call the userʼs attention to the possible danger. Read and follow

them carefully in order to prevent a safety accident.

: Warning and Caution are indicated in this guide and the product itself to help protect the users

from danger.

WARNING

CAUTION

WARNING

nIn-use

Request to the service center or installation

specialty store when the product becomes wet.

• It will cause fire or electric shock.

Do not give the shock using sharp and

pointed objects.

• It will cause breakdown by damaging parts.

nIn-use

CAUTION

Do not clean using the

powerful detergent like

solvent but use soft cloths.

• It will cause fire or product

deformation.

Do not press the screen

using powerful pressure or

select two buttons.

• It will cause product breakdown or

malfunction.

Do not touch or pull the lead

wire with wet hands.

• It will cause product breakdown or

electric shock.

4Wired Remote Controller

Part Description

Accessory

Connecting Cable (1EA) Fixing Screw (2EA) Owner / Installation Manual

Simple Wired Remote Controller

Each function will be shown on the display panel for three seconds or so when the power is applied at first.

TEMP

FAN

SPEED

OPER

MODE

1. Operation Display Panel

2. Temperature Control Button

3. Fan Speed Button

4. On/Off Button

5. Operation Mode select Button

Ownerʼs & Installation Manual 5

ENGLISH

Installation instruction

1. Please fix tightly using provided screw after placing remote controller setup board

on the place where you like to setup.

- Please set it up not to bend because poor setup could take place if setup board bends.

Please set up remote controller board fit to the reclamation box if there is a reclamation box.

2. Can set up Wired remote controller cable into three directions.

- Setup direction: the surface of wall reclamation, upper, right

- If setting up remote controller cable into upper and right side, please set up after removing remote controller

cable guide groove.

Remove guide groove with long nose.

①

Reclamation to the surface of the wall

②

Upper part guide groove

③

Right part guide groove

Installation instruction

Installation instruction

6Wired Remote Controller

Wall

Side

Wall

Side

Wall

Side

Wall

Side

5. Please fix remote controller upper part into

the setup board attached to the surface of the

wall, as the picture below, and then, connect

with setup board by pressing lower part.

- Please connect not to make a gap at the remote controller

and setup boardʼs upper and lower, right and left part.

When separating remote controller from

setup board, as the picture below, after

inserting into the lower separating hole using

screw driver and then, spinning clockwise,

remote controller is separated.

- There are two separating holes. Please individually

separate one at a time.

- Please be careful not to damage the inside

components when separating.

3. Please connect indoor unit and remote controller using connection cable.

4. Please use extension cable if the distance between wired remote controller and

indoor unit is more than 10m.

Please check if connector is normally connected.

Connecting cable

Indoor

Unit side

TEMP

FAN

SPEED

OPER

MODE

When installing the wired remote controller, do not bury it in the wall.

(It can cause damage in the temperature sensor.)

Do not install the cable to be 50m or above.

(It can cause communication error.)

• When installing the extension cable, check the connecting direction of the connector of the remote controller

side and the product side for correct installation.

• If you install the extension cable in the opposite direction, the connector will not be connected.

• Specification of extension cable: 2547 1007 22# 2 core 3 shield 5 or above.

CAUTION

Ownerʼs & Installation Manual 7

ENGLISH

Installation instruction

GND

12V

Signal wire

TEMP

FAN

SPEED

OPER

MODE

GND

12V

B Y R B Y R

MASTER SLAVE

Signal wire GND

12V

Signal wire

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

Group control

1. When installing more than 2

units of air conditioner to one

wired remote controller, please

connect as the right figure.

• If it is not event communication

indoor unit, set the unit as slave.

• Check for event communication

through the product manual.

2. When installing more than 2 wired

remote controllers to one air

conditioner, please connect as the

right picture.

• When installing more than 2 units of wired

remote controller to one air conditioner, set

one wired remote controller as master and

the others all as slaves, as shown in the

right picture.

• You cannot control the group as shown in

the right for some products.

•

Refer to the product manual for more detail.

When controlling multiple indoor units with event communication function with one remote

controller, you must change the master/slave setting from the indoor unit.

Indoor units, the master/slave configuration of the product after completion of indoor unit power

ʻOFFʼ and then ʻONʼ the power after 1 minutes elapsed sign up.

- For ceiling type cassette and duct product group, change the switch setting of the indoor PCB.

- For wall-mount type and stand type product, change the master/slave setting with the wireless

remote controller. (Refer to wireless remote controller manual for detail)

hWhen installing 2 remote controllers to one indoor unit with event communication function, set

the master/slave of the remote controller. (Refer to remote controller master/slave selection)

When controlling the group, some functions excluding basic operation setting, fan level

Min/Mid/Max, remote controller lock setting and time setting may be limited.

<When simultaneously connecting

2 sets of wired remote controller>

• When controlling in groups, set the master/slaver of the remote controller. Refer to

Installer setting section on how to set master/slave for more detail.

2345678 1

2345678

#3 switch OFF: Master

(Factory default setting)

#3 switch ON: Slave

8Wired Remote Controller

1) General air-conditioner product

jSome contents may not be displayed depending on the product function

Installation instruction

Installer setting mode is to set the detail function of the remote controller.

If the installer setting mode is not set correctly, it can cause problems to the product, user injury or property

damage. This must be set by an certificated installer, and any installation or change that is carried out by a

non-certificated person should be responsible for the results. In this case, free service cannot be provided.

CAUTION

Installer Setting -How to enter installer setting mode

TEMP

FAN

SPEED

OPER

MODE

Function Code

Value

If you want to set installer setting mode, Press

the Temperature up button and the oper mode

button same time for five seconds.

When you enter the setting mode

Initially. Function code is displayed

on the LCD screen.

No. Function Code Value

1 Test Run 01 01:Set

2 Address Setting 02 00~FF : Address

01:VeryLow 0 ~ 255

02:Low

3 E.S.P. Value 03 03:Med

04:High

05:Very High

01:Remo

4 Thermistor 04 02:Indoor

03:2TH

01:Med

02:Low

5 Ceiling Height 05 03:High

04:Very High

01:V-H

02:F-H

6 Static Pressure 06 03:V-L

04:F-L

7 Master Setting 07 00:Slave

01:Master

8Celsius 12 00:Celsius (Optimized only for U.S.A)

Fahrenheit Switching 01:Fahrenheit

Function Code ESP valueESP step

Ownerʼs & Installation Manual 9

Installation instruction

TEMP

FAN

SPEED

OPER

MODE

When pressing the button and

button simultaneously for more than 3

seconds, the system will be entered

into the installer setting mode.

- After entering into the installer setting

mode, select the test run mode code

value by pressing the button.

* Test run mode code value : 01

When pressing the button, the test

operation mode will be performed, and it

is displayed as shown in the left figure.

When pressing the button and

button simultaneously for more than 3

seconds after the setting has been

completed, the setting mode will be

released.

- If there isn’t any button input for more

than 25 seconds, the installer setting

mode will also be released.

When approx. 18 minutes are elapsed

after starting of the test oper-mode, the

system will be stopped automatically

and converted to the standby state.

- If any button is inputted during the test

run mode, the test run mode will be

forced to be relreased.

OPER

MODE

OPER

MODE

OPER

MODE

OPER

MODE

Installer Setting -Test Run Mode

After installing the product, you must run a Test Run mode.

For details related to this operation, refer to the product manual.

•What is the test run mode??

- This means the operation of the product under the cooling, strong wind, and Comp on state

without performing room temperature control in order to confirm the installed state during the

product installation.

ENGLISH

10 Wired Remote Controller

Installation instruction

* In the case when the lock is set up at the central controller, ʻHLʼ will be indicated on the display

window of the wired remote controller and the indoor unit will not be controlled by the remote

controller.

It's the function to use for connecting central control.

Please refer to central controller manual for the details

TEMP

FAN

SPEED

OPER

MODE

When pressing the button and

button simultaneously for more than 3

seconds, the system will be entered into the

installer setting mode.

After entering into the installer setting mode,

select the central control address setting

code value by pressing the button.

* Setting address of central control code

value : 02

When pressing the button, the system

will be set up with the address value which

has been established at present.

When pressing the button and

button simultaneously for more than 3

seconds after the setting has been

completed, the setting mode will be released.

- If there isn’t any button input for more than

25 seconds, the installer setting mode will

also be released.

Set up the group nember and indoor unit with

the temperature adjustment(▲,▼) buttons.

For example, when setting as

[ Group number=2 Indoor number=3 ]

it will be displayed as shown in the left figure.

OPER

MODE

OPER

MODE

TEMP

Group number

Indoor unit number

OPER

MODE

Installer Setting - Setting Address of Central Control

• If you connect the indoor unit to the central controller, you should set the network address

of the indoor unit so that the central controller could recognize it.

• The center-control address is composed of the group number and the indoor-unit number.

Note : The remote controller displays 'HL' if central controller has locked the remote controller .

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG Fernbedienung Handbücher

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung