LG WM3455HS Bedienungsanleitung

PARTS AND FEATURES

DETERGENT DISPENSER DRAWER

This three-compartment drawer provides separate

dispensers for prewash and main wash detergent,

and liquid fabric softener.

CONTROL PANEL WITH LED DISPLAY

Simple electronic controls are user-friendly.

The LED display indicates cycle options and

cycle time during operation.

LARGE-CAPACITY STAINLESS STEEL DRUM

The large capacity stainless steel drum offers

extreme durability and is tilted to improve

efficiency and allow easier access for large items.

NOTE: No matter how large the article, there

must still be room for the clothes to tumble.

DIRECT-DRIVE MOTOR

Direct-drive motor eliminates the belt and pulleys

found on most washers to provide improved

performance and reliability while increasing

energy efficiency.

DRAIN ACCESS PANEL

Provides access to the drain line and drain

pump filter.

EASY-ACCESS DOOR

Extra-large door locks during operation and

features a delay to prevent the door from being

opened until the washer interior has cooled and

the water level has lowered.

LEVELING FEET

Four leveling feet (two in the front and two in

the back) adjust to improve washer stability on

uneven floors.

Rear of Washer

Included Accessories

Hot and Cold

Water Hoses

Wrench

(for removing shipping

bolts and adjusting

leveling feet)

Tie Strap

(for securing

drain hose)

Elbow Bracket

(for securing drain

hose)

Non-skid pads Caps (4)

(for covering

shipping bolt holes)

SPECIAL FEATURES

INSTALLATION INSTRUCTIONS

CHOOSE THE PROPER LOCATION

CLEARANCES

Allow at least 19.8 in. (50.3 cm) in front of the

washer to open the door.

To ensure sufficient clearance for water lines and

airflow, allow minimum clearances of at least

1 in. (2.5 cm) at the sides and 4 in. (10 cm)

behind the unit. Be sure to allow for wall, door,

or floor moldings that may increase the required

clearances.

• Do not remove ground prong. Do not use

an adapter or extension cord. Plug into a

grounded 3-prong outlet. Failure to follow this

warning can cause serious injury, ﬁre, electrical

shock, or death.

Power Outlet

• The power outlet must be within 60 in. (1.5 m) of

either side of the washer.

• The appliance and outlet must be positioned so

that the plug is easily accessible.

• Do not overload the outlet with more than one

appliance.

• The outlet must be grounded in accordance with

current wiring codes and regulations.

• Time-delay fuse or circuit breaker is

recommended.

NOTE: It is the personal responsibility and

obligation of the product owner to have a

proper outlet installed by a qualified electrician.

wWARNING

• Washer is heavy! Two or more people

are required when moving and unpacking

the washer. Failure to do so can result in back

or other injury.

• Store and install the washer where it will not

be exposed to temperatures below freezing

or exposed to outdoor weather conditions.

Failure to follow this warning can cause serious

injury, ﬁre, electrical shock, or death.

• Properly ground washer to conform with all

governing codes and ordinances. Failure to

follow this warning can cause serious injury, ﬁre,

electrical shock, or death.

• To reduce the risk of electric shock, do not

install the washer in humid spaces. Failure to

follow this warning can cause serious injury, ﬁre,

electrical shock, or death.

21.6" (54.86 cm)

25.2" (64 cm)

45" (114.3 cm)

33.5" (85.09 cm)

3.5" (8.89 cm) 24" (60.96 cm) 1" (2.5 cm)1" (2.5 cm)

INSTALLATION INSTRUCTIONS

FLOORING

NOTE: Please note that the floor must be strong

and rigid enough to support the weight of the

washer when fully loaded, without flexing or

bouncing. If your floor has too much flex in it,

you may need to reinforce it to make it more

rigid. A floor that is adequate for a top-loading

washer may not be rigid enough for a front-

loading washer due to the difference in the spin

speed and direction. If the floor is not solid, your

washer may vibrate and you may hear and feel

the vibration throughout your house.

• To minimize noise and vibration, the washer

MUST be installed on a solidly constructed ﬂoor.

See the NOTE at right.

• Allowable slope under the entire washer is

1° maximum.

• Carpeting and soft tile surfaces are not

recommended.

• Never install the washer on a platform or weakly

supported structure. Use only an approved

accessory pedestal as described below.

NOTE: Before installing the

washer, make sure the floor is

clean, dry and free of dust, dirt,

water and oils so the washer feet

can not slide easily. Leveling

feet that can move or slide on the floor can

contribute to excess vibration and noise due to

poor contact with the floor.

INSTALLATION INSTRUCTIONS

If you must lay the washer down to remove the

base packaging materials, always lay it carefully

on its side. Do NOT lay the washer on its front

or back.

IMPORTANT: To prevent internal damage

during transport, the washer is equipped with

4 shipping bolts and plastic retainers. These

bolts and retainers MUST be removed before

operating the washer.

• Failure to remove shipping bolts and retainers

may cause severe vibration and noise, which can

lead to permanent damage to the washer. The

cord is secured to the back of the washer with

a shipping bolt to help prevent operation with

shipping bolts in place.

Remove the retainers by turning them slightly

while pulling. Rotate and press the hole caps

into the shipping bolt holes.

Starting with the bottom 2 shipping bolts,

use the included wrench to remove the

4 shipping bolts by turning them

counterclockwise.

NOTE: Save the bolts and retainers for

future use. To prevent damage to internal

components, the shipping bolts and

retainers must be installed when

transporting the washer.

Cap

Carton Base

UNPACKING

INSTALLATION INSTRUCTIONS

CONNECTING THE WATER LINES

Insert a rubber seal into the threaded

ﬁttings on each hose.

Rubber Seal

Water Hose

(to tap)

Rubber Seal

Water Hose

(to water inlet

on washer)

3Attach the hot water line to the hot water

tap. Attach the cold water line to the cold

water tap.

Tighten the ﬁttings securely. Open the water

taps fully to check for leaks.

Water Tap

NOTE: Do not cross-thread the hose ﬁttings.

Attach the hot water line to the red hot water

inlet on the back of the washer. Attach the

cold water line to the blue cold water inlet on

the back of the washer. Tighten the fittings

securely.

• IMPORTANT: Use new hoses when installing

the washer. Do NOT reuse old hoses.

• IMPORTANT: Use ONLY the inlet hoses

provided by LG with this laundry product.

Aftermarket hoses are not guaranteed to ﬁt or

function correctly. Other hoses may not tighten

correctly and could cause leaks. Subsequent

damage to product or property will not be

covered under the terms of LG's warranty.

• Water supply pressure must be between 14.5

PSI and 116 PSI (100~800 kPa). If the water

supply pressure is more than 116 PSI,

a pressure reducing valve must be installed.

• Periodically check the hose for cracks, leaks,

and wear, and replace the hose if necessary.

• Make sure that the water lines are not stretched,

pinched, crushed, or kinked.

• The washer should never be installed or stored

in a location subject to freezing temperatures.

Damage to the water lines and internal

mechanisms of the washer can result. If the

washer was exposed to freezing temperatures

prior to installation, allow it to stand at room

temperature for several hours before use.

Cold Hot(option)

Hot water tap

Cold

water

tap

INSTALLATION INSTRUCTIONS

CONNECTING THE DRAIN LINE

Stand

Pipe

Tie Strap

Clip the end of the hose into the elbow bracket.

Insert the end of the drain hose into a standpipe.

Use tie strap to secure the drain hose in place.

NOTE: Total height of the hose end should not

exceed 96 in. (244.8 cm) from the bottom of the

washer.

Option 1: Standpipe

Elbow

Bracket

Drain

Hose

Clip the end of the hose into the elbow bracket.

Hang the end of the drain hose over the side of

the laundry tub. Use tie strap to secure the drain

hose in place.

NOTE: Total height of the hose end should not

exceed 96 in. (244.8 cm) from the bottom of the

washer.

Laundry

Tub

Option 2: Laundry Tub

Elbow

Bracket

Tie

Strap

Drain

Hose

• The drain hose should always be properly

secured. Failure to properly secure the drain

hose can result in ﬂooding and property

damage.

• Do not install the end of the drain hose higher

than 96 in. (244.8 cm) above the bottom of the

washer.

• The drain must be installed in accordance with

any applicable local codes and regulations.

• Make sure that the water lines are not stretched,

pinched, crushed, or kinked.

NOTE: If the drain hose is extended more than 4

inches beyond the end of the end of the elbow

bracket, mold, or microorganisms could spread to

the inside of the washer.

No more than

4 inches

Elbow Bracket

INSTALLATION INSTRUCTIONS

LEVELING THE WASHER

Position the washer in the final location, taking

special care to not pinch, strain, or crush the

water and drain lines. Place a level across the

top of the washer.

Leveling Feet

Leveling

Feet

The drum of your new washer spins at very high

speeds, up to 1,300 RPM. To minimize vibration,

noise, and unwanted movement, the floor must be

a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as

necessary to level the washer. Extending the

leveling feet more than necessary can cause

the washer to vibrate.

Loosen the locknuts on all 4 leveling feet

until you can turn the feet with the included

wrench. Turn clockwise to raise the washer

or counterclockwise to lower it.

Raise Lower

• All four leveling feet must rest solidly on the

ﬂoor. Rock the washer gently from corner to

corner to make sure that the washer does

not rock.

3Once the washer is level from side to side and

front to back, tighten all locknuts securely.

Make sure that all 4 leveling feet are in firm

contact with the floor.

NOTE: To make sure that the washer is

properly level, run the washer with a test load:

place approximately 6 pounds of laundry

in the machine. Then, press POWER, press

RINSE+SPIN, and then press the START/

PAUSE button. (See the following sections for

additional information on cycle selection and

operation.)

Verify that the washer does not rock or vibrate

excessively during the spin cycle.

If the washer vibrates or shakes, adjust

the leveling feet until the washer is stable and

retest.

Tighten all 4

locknuts securely

INSTALLATION OF NON-SKID PADS (OPTIONAL)

Some floor surfaces are too slippery to prevent

the washer from moving on the floor during

heavily unbalanced loads. While it is normal for

an occasional load to be out of balance, excess

noise and vibration can result from the washer

moving out of position. If these conditions are

encountered, follow the instructions below for

installation of the non-skid pads. These pads

will help prevent the washer from moving during

heavy out of balance conditions thereby reducing

noise and vibration.

[Place the pads under both front feet.

This side up

Stick adhesive side to floor

Remove backing

• Non-skid pads

Andere Handbücher für WM3455HS

Inhaltsverzeichnis

Andere LG Waschmaschine Handbücher

LG WT18WV6 Bedienungsanleitung

LG SB-19108WD Bedienungsanleitung

LG F1443KDS2 Bedienungsanleitung

LG TS12CM Bedienungsanleitung

LG F14U2TCN0 Bedienungsanleitung

LG WP-1250R Bedienungsanleitung

LG T1349TEFT0 Bedienungsanleitung

LG F4WV909P2 Series Bedienungsanleitung

LG F1252RD7 Bedienungsanleitung

LG WFS1658EKD Bedienungsanleitung

LG WD-12320BDK Bedienungsanleitung

LG F4V5 YP Series Bedienungsanleitung

LG SteamWasher WM2550HWCA Bedienungsanleitung

LG SteamWasher WM3550HVCA Bedienungsanleitung

LG F10F6RDS27 Bedienungsanleitung

LG T7001TDDLC Bedienungsanleitung

LG F1 F6RDS2 Series Bedienungsanleitung

LG WF-T507 Bedienungsanleitung

LG WD-10151SUP Bedienungsanleitung

LG WFS2018EKD Bedienungsanleitung

LG F4T2VYM1S Bedienungsanleitung

LG Studio WashTower SWW 50 3 Series Bedienungsanleitung

LG WXL-1014 Series Bedienungsanleitung

LG WFS1918EKD Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung

Samsung

Samsung WF16J9800K Series Bedienungsanleitung

Whirlpool

Whirlpool FRONT-LOADINGAUTOMATIC WASHER Bedienungsanleitung