Liebert Series 300 Bedienungsanleitung

POWER PROTECTION

OPERATOR’S

MANUAL

Series 300

Three Phase

Uninterruptible

Power System

Load Bus

Synchronization

Option

WARNING

READ BEFORE

HANDLING

OR INSTALLING.

ONLY QUALIFIED

PERSONNEL

SHOULD HANDLE

THIS EQUIPMENT.

DISCONTINUED

PRODUCT

Series 300 Load Bus Synchronization

Table of Contents

Section 1 Introduction

1.0 System Description ................................................................................................ 1

Section 2 Theory of Operation

2.1 General Description................................................................................................ 2

2.2 Load Bus Sync Controller ..................................................................................... 2

2.3 Series 300 LBS Module Interface .......................................................................... 2

2.4 System Operation .................................................................................................. 3

Section 3 Operation

3.1 Operator Controls .................................................................................................. 4

3.2 Operator Procedures .............................................................................................. 5

DISCONTINUED

PROD UC T

Series 300 Load Bus Synchronization 1

SECTION 1 INTRODUCTION

1.0 SYSTEM DESCRIPTION

The Liebert Load Bus Sync™ (LBS) option keeps the output of two independent Uninterruptible

Power Systems (UPSs) in sync, even when the two UPSs are operating from two different power

sources. Any UPS will typically sync to its own bypass source. As long as both UPSs are tied to the

same input and bypass sources, they will automatically stay in sync. However, if the UPSs are

operating on batteries, or different backup generators, or asynchronous bypass sources, their outputs

will tend to drift out of sync.

Maintaining sync is critically important for installations with dual power distribution systems. These

sites typically feature Liebert Precision Power Centers (PPC) with Liebert Static Bus Transfer

Switches. Each PPC has dual inputs: it can receive power from either UPS, and switch seamlessly

between the two as long as the UPS outputs are held in close synchronization. This provides

redundancy down to the PPC level. It also permits one entire half of the distribution system (upstream

of the PPC) to be taken offline for maintenance or repairs.

The Load Bus Sync option consists of an LBS interface in each UPS module plus one LBS controller

enclosure installed between the UPSs.

Figure 1. LBS Controller Enclosure

DISCONTINUED

PROD UC T

Series 300 Load Bus Synchronization 2

SECTION 2 THEORY OF OPERATION

2.1 GENERAL DESCRIPTION

The Liebert Series 300 Load Bus Sync (LBS) option works by monitoring the sync reference signals of

two UPS modules, each equipped with a specially designed interface. The LBS remains dormant until

the outputs of the UPS modules drift more than a predetermined amount out of sync. In the event of an

out of sync condition, the LBS becomes active and brings the output of both UPS modules back in

sync, and then resumes the dormant state.

2.2 LOAD BUS SYNC CONTROLLER

The Series 300 LBS controller fits into a compact 20x24 inch enclosure. The front panel controls are

simple and fault tolerant. They enable the operator to do the following:

A. Select whether the controller will function automatically or be “Off.”

B. Select which UPS, (System 1 or System 2) will become the Designated Master System

(DMS). The other UPS module will become the Designated Slave System (DSS).

2.3 SERIES 300 LBS MODULE INTERFACE

In order for the LBS controller to send and receive signals from the Series 300 modules, each module

must have the proper interface installed. The Series 300 interface consists of two main components as

follows:

A. The LBS Interface Panel

B. The LBS Adapter PWA

The LBS Interface Panel has many configurations to accommodate the many input and output voltages

available on the Series 300 UPS. The LBS Adapter PWA has only one configuration, which is used with

all Series 300 LBS installations.

The LBS Interface Panel performs the following functions:

A. Receives and scales sync signals from the LBS Controller.

B. Receives signals from the LBS Controller to determine whether to use internal sync or

sync to the other UPS module.

C. Receives static switch disable signals from the LBS Controller.

D. Provides the LBS Controller with bypass voltage signals, output voltage signals and

bypass available signals.

E. Provides the LBS Controller with 120 VAC control power.

The LBS Adapter PWA performs the following functions:

A. Receives and shapes sync signals for the LBS Interface Panel and routes the sync signal

to the processor board.

B. Selects the sync source, either internal or from the other UPS based on signals that

originate with the LBS Controller and passed on through the LBS Interface Panel.

C. Disables the static switch on the slave UPS when the slave UPS is acquiring sync with the

master UPS.

DISCONTINUED

PROD UC T

Series 300 Load Bus Synchronization 3

D. Operates the flashing warning light on the front panel of the slave UPS indicating that the

Main Rotary Switch should not be operated while sync is being acquired with the master

UPS.

2.4 SYSTEM OPERATION

The Series 300 LBS option performs the following functions:

A. Continuously senses the phase relationship between the outputs of the two UPS modules

that make up the system.

B. If the two systems lose sync with each other for more than a predetermined period of time

(adjustable from 0.1 to 5 seconds) and the AUTO/OFF switch is set to the AUTO position

then the LBS will sync the Designated Slave System (DSS) to the Designated Master

System (DMS). The DMS and DSS are selected manually using the master system select

switch. If the DSS is on bypass and unable to sync to the DMS then the DMS will sync to

the output bus of the DSS. This reselection of the master system will be accomplished

automatically.

C. Continuously monitors the sync and the quality of the bypass input voltage to both

systems. Once the sync and voltage quality between to two systems have been restored

for 5 seconds, the LBS will become dormant and allow each system to operate

independently.

Note: Failure of any part of the LBS will not cause system failure. The worst case effect would be that

the two systems would not be able to synchronize to each other.

DISCONTINUED

PROD UC T

Series 300 Load Bus Synchronization 4

SECTION 3 OPERATION

3.1 OPERATOR CONTROLS

Operation of the LBS has deliberately been kept as simple possible. There are only three controls and

five indicator lights on the SERIES 300 LBS Controller enclosure. Each LBS equipped UPS module has

one indicator light mounted on the bezel below the front display panel. The indicators are:

A. LBS Enabled. Indicates that the LBS circuitry is in the Automatic Mode.

B. System Non-Sync. Indicates that the DSS is no longer in sync with the DMS. This alarm

will appear during the transition from internal bypass sync to DMS sync.

C. LBS Active. Indicates that the LBS circuitry has taken over the sync of the UPS. If the

System Non-Sync indicator is also on, it means that synchronization is in progress.

D. Load 1 Sync to Load 2. Indicates that the UPS critical bus is synchronized to the bypass

input of the DMS, in this case System 2. This indicator will turn on when the sync process

is complete.

E. Load 2 Sync to Load 1. Indicates that the UPS critical bus is synchronized to the bypass

input of the DMS, in this case System 1. This indicator will turn on when the sync process

is complete.

F.Warning LBS Active. This indicator is located on the bezel below the front display panel

on each UPS module. This indicator will be flashing when the DSS is acquiring sync with

the DMS. This is a warning, not to operate the Main Rotary Switch.

Standard LBS controls are:

A. Mode Select Switch. Provides manual selection of automatic operation or “OFF” modes.

In the automatic mode the LBS will be enabled. In the “OFF” mode, both UPS modules

will synchronize independently.

B. Master Select Switch. Provides manual selection of the DMS source. The LBS circuitry

will automatically switch DMS sources should the initially selected DMS lose bypass

input.

C. Lamp Test. Push this button to test the indicators lights on the LBS Controller. There is

no lamp test for the warning indicators on the UPS modules.

3.2 OPERATOR PROCEDURES

The only two operator controls are the Mode Select Switch and the Master Select Switch. The Mode

Select Switch can be left in the Automatic position all the time. The OFF position can be selected at

times when it is desirable to allow the UPS systems to synchronize independently.

The Master Select Switch allows the operator to chose which UPS bypass source will provide the

reference sync signal.

In normal operation, both System 1 and System 2 will be functioning and the LBS Mode Select Switch

will be in the Automatic position. The LBS enable indicator and one of the Load X Sync to Load Y

indicators will be illuminated. If the two UPS systems drift out of sync (while on battery for example),

the LBS Active and System Non Sync indicators will be illuminated. The Load X Sync to Load Y

DISCONTINUED

PROD UC T

Series 300 Load Bus Synchronization 5

indicator will be off during the synchronization process and turn back on when the process is

completed.

When the slave system is in the process of synchronizing to the master system, the Warning Indicator on

the slave system will be flashing on and off. This is to warn against operating the Main Rotary Switch.

SL-24536 (5/00)

DISCONTINUED

PROD UC T

Andere Handbücher für Series 300

Inhaltsverzeichnis

Andere Liebert UPS Handbücher

Liebert

Liebert UPStation GX Bedienungsanleitung

Liebert

Liebert GXT4 Bedienungsanleitung

Liebert

Liebert GXT3 Bedienungsanleitung

Liebert

Liebert PowerSure Personal Bedienungsanleitung

Liebert

Liebert 350-500 VA Bedienungsanleitung

Liebert

Liebert PB Series Bedienungsanleitung

Liebert

Liebert 50 and 60 Hz Bedienungsanleitung

Liebert

Liebert UPStation GXT 2U Bedienungsanleitung

Liebert

Liebert GXT2-10000RT208 Bedienungsanleitung

Liebert

Liebert SERIES 610 Bedienungsanleitung

Liebert

Liebert NXC 40kVA Bedienungsanleitung

Liebert

Liebert NXL Bedienungsanleitung

Liebert

Liebert GXT2-10000RT208 Bedienungsanleitung

Liebert

Liebert UPStation GXT 2U Bedienungsanleitung

Liebert

Liebert SERIES 610 Bedienungsanleitung

Liebert

Liebert 2700VA Bedienungsanleitung

Liebert

Liebert itON BX Bedienungsanleitung

Liebert

Liebert UPStation GXT 2U Bedienungsanleitung

Liebert

Liebert GXT2-6000RTL630 Bedienungsanleitung

Liebert

Liebert GXT3-5000RT230 Bedienungsanleitung

Liebert

Liebert UPS Bedienungsanleitung

Liebert

Liebert UPStation GXT700MT-120 Bedienungsanleitung

Liebert

Liebert 700-3000 VA Bedienungsanleitung

Liebert

Liebert UPSTATION GXT3X1-6000 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung