Lifetime 1270 Bedienungsanleitung

Copy

INSTRUCTION #1025093

The product you just purchased could be FREE!

benets:

1. You automatically will be entered to win $200 in our monthly drawing!

2. In the unlikely event of a product recall or safety modication, we can

notify you immediately and directly.

3. You may choose to receive Preferred Customer Announcements and

promotions regarding new Lifetime products.

www.lifetime.com

**U.S. and Canada customers ONLY**

IF ASSISTANCE IS NEEDED,

DO NOT CONTACT THE STORE!!!

CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)

Call, or visit our Website for Saturday hours.

Save this instruction in the event that the manufacturer has to be contacted for

replacement parts.

MODEL #1270

WARNING

To ensure your safety, do not attempt to assemble

this system without reading and following all

instructions carefully. Identify and inventory the

parts using the Parts List. Failure to comply with

any of the warnings in these instructions may

result in serious personal injuries such as cuts,

broken bones, nerve damage, paralysis, brain

injury, or death. Failure to comply may also result

in property damage. Please heed all warnings

and cautions.

PROCOURT®

BASKETBALL SYSTEM

2/6/2007

**For customers outside the U.S. or Canada, please contact the store for assistance.**

Copy

Problem / Possible Cause

ASSEMBLY TROUBLESHOOTING

1. Identify your pole sections:

TOP: Crimped end with six holes down the

middle.

MIDDLE: Warning Sticker.

BOTTOM: A slot at the top of the pole, two

holes near the middle of the pole and four

holes at the bottom.

2. Slide the Top Pole inside the bottom of

the Middle Pole, crimped end rst, until

it extends out of the top of the Middle

Pole. There should be no hardware or parts

attached to either pole at this point.

2. My Top Pole will not slide through my

Middle Pole:

The pole sections are not completely round.

Align the holes in the side of the Top Pole with

the holes in the Middle Pole section before

sliding it through.

1. My Top and Middle Poles will not

assemble:

It is easy to confuse the pole sections. Refer

to the next column for hints on how to tell

them apart.

3. How do I fasten my poles together?

The Top and Middle Pole sections are

fastened together with a Carriage Bolt

through both poles. The Bottom and Middle

Pole sections are held together with a friction

weld and also with a pole joint Screw.

Follow the instructions for pole assembly

carefully. When the poles are seated together,

a friction weld is created between the Bottom

and Middle Pole sections. A pole joint Screw

will also be attached.

4. My Pole Braces will not attach:

The Pole Braces are designed to t snugly

to the Base and the Bottom Pole section for

stability.

The Pole Braces should be attached to the

Base rst, but the hardware should only be

nger tight at this point. Use gentle pressure

on the Pole Braces to align them with the holes

in the Bottom Pole. Then completely tighten

all Base hardware before proceeding.

5. How d o I b e n d my Backboar d

Brackets?

Although the Backboard Brackets are made

of steel, they are designed to bend with only

a small amount of force.

The Backboard Brackets should be fastened

nger tight to the Rim holes in the Backboard.

Grasp the tops of the Backboard Brackets and

bend them away from each other with steady

force.

Solution

Who Do I Call If I Have

Questions Or Problems?

1-800-225-3865

HOURS:

7:00 AM – 5:00 PM MST

MONDAY – FRIDAY

**A MINIMUM OF TWO ADULTS ARE

REQUIRED FOR ASSEMBLY**

PARTS LIST

ID Part # Description Qty

TP 1018558 Top Pole 1

MP 1018559 Middle Pole 1

BP 1018560 Bottom Pole 1

LB 1018713 Left Backboard Bracket 1

RB 1018711 Right Backboard Bracket 1

BB 1025145 Backboard 1

AA 510022 Wheel 2

AB B110001 1/2” x 15 3/4” Axle 1

AC 1002834 Base 1

FS16400 Warning Sticker (Applied) 1

AD 1018886 Rim 1

AE 1018850 Pole Brace 2

Main Hardware (1001200)

MA BS02000 1/4” x 3/4” Self-Drilling Screw 1

MB 300095 5/16” Cap Nut 1

MC 302014 5/16” Flat Washer 1

MD 302012 5/16” Zinc-Plated Nut 1

ME CH06899 Pole Locking Knob 1

MF 1000805 5/16” x 3 1/4” Carriage Bolt 2

Rim Hardware (HP18600)

RA 300027 5/16” x 1 3/4” Hex Bolt 2

RE BB01400 2” U-Bolt 1

RC 302090 5/16” Nylock Flange Nut 4

MC 302014 5/16” Flat Washer 4

RD DD00200 Net 1

Backboard Hardware (1002576)

PA BS00800 5/16” x 1” Screw (for plastic) 2

PB 300075 5/16” Flange Lock Nut 2

PC 302062 5/16” x 3 1/4” Hex Bolt 2

PD AM01500 Rim Support Channel 1

Base Hardware (1007262)

BA CF00199 1 1/4” Base Plug 2

BB 300097 5/16” Nylock Nut 2

BC 300030 5/16” x 1” Hex Bolt 2

MC 302014 5/16” Flat Washer 4

BE 500032 1/2” x 1/8” Spacer 2

BF BD00200 1/2” x 7” Axle 1

HA 1003221 1/4” T-Nut 1

HB 1003222 1/4” Hex Shoulder Screw 1

Tools and Materials Required for Assembly

(Not Included)

1. Adjustable Wrench

2. 319 lbs. of Sand/ Water Supply

3. 1/2” Wrenches (2)

4. Funnel

5. Phillips Screwdriver

6. Scrap Wood/Cardboard

7. 3/8” Socket Wrench

8. 7/16” Wrench

9. Pliers

BA MC

HARDWARE IS ACTUAL SIZE

MA BE

Before Beginning Assembly

A. Keep the hardware bags and their contents separate. If any

parts are missing, call our Customer Service Department.

B. TesttallBoltsbyinsertingthemintotheirrespectiveholes.

If necessary, carefully scrape away any excess powder coating

buildup from inside the holes. Do not scrape away all of the

powder coating. Bare metal may rust.

(Not actual size)

TP MP BP

PoleSectionIdentication

Identify the pole sections before beginning assembly. Failure to assemble the

pole sections correctly may result in severe personal injury or property damage

as described on Page Two.

ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY

CANNOT BE SEPARATED.

Top Pole:

Holes down

the middle

of the pole.

The Top Pole

is packaged

inside the

Middle Pole.

Middle Pole:

The Top Pole

is packaged

inside the

Middle Pole.

Warning

Sticker.

Bottom Pole:

A small slot at

the top of the

pole, a set of

holes near the

middle and

two sets of

holes near the

bottom.

SAFETY INSTRUCTIONS

Owner must ensure that all players know and follow these rules for safe operation of

the system.

To ensure safety, do not attempt to assemble this system without following the

instructions carefully. Check entire box and inside all packing material for parts and/

or additional instruction material. Before beginning assembly, read the instructions

and identify parts using the hardware identier and parts list in this document.

Proper and complete assembly, use and supervision are essential for proper

orientation and to reduce the risk of accident or injury. A high probability of serious

injury exists if this system is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR

PROPERTY DAMAGE AND WILL VOID WARRANTY.

• If using a ladder during assembly, use extreme caution.

• Two capable adults are recommended for this operation.

• Check base daily for leakage. Leaks will cause system to fall.

• Assemble the pole sections properly (if applicable). Failure to do so could cause

the pole sections to separate during play or transport.

• Minimum operational height is 7’6” (2.23m) to the rim.

Most injuries are caused by misuse and/or not following instructions. Use

caution when using this system.

Required For This Page:

MD (1)

(2)

(1)

1/2” Wrench

1Pull the plastic off the Top

Pole (TP) while it is still

inside the Middle Pole (MP).

Make sure the crimped side of

the Top Pole faces the same

direction as the Warning Sticker.

You may need to loosen the poles

before pulling the plastic out.

(1)

You may need to push the

Nut (MD) into the Knob (ME)

with a 5/16” Bolt.

Be sure to use the

Zinc Nut (MD).

WARNING

Do not overtighten the Cap

Nut. If the end of the Bolt

breaks through the plastic

cap, call our Customer Service

Department at the number on

Page Two. Exposed threads

on the end of the Bolt may

cause serious injuries such as

those listed on Page Two.

Pull the Top Pole

through the Middle Pole

far enough to clear the

holes near the bottom of

the Middle Pole.

1001200

Position the Top Pole

(TP) at its lowest

height setting.

1001200 (1)

Screwdriver

Required For This Page:

Align the slot in the Bottom Pole (BP) with the hole in the Middle

Pole (MP) and slide the Middle Pole over the Bottom Pole.

Do not jam the poles together until instructed.

Insert the 1/4” x 3/4”

Screw (MA) through the

small hole in the Middle

Pole and into the slot in

the Bottom Pole.

The Screw will spin

freely once installed.

**Make sure Steps 1 through 4 are complete before

starting this Step.**

The Top Pole cannot be inserted after the Middle

and Bottom Poles are joined.

Strike the poles rmly 5 to 6 times on a piece of

scrap wood or cardboard.

If the Middle Pole does not completely cover the

slot on the Bottom Pole after seating, DO NOT

COMPLETE ASSEMBLY.

Do not hit your feet with the pole sections, as

serious injury could occur.

The poles must be seated together!! Even if the pole

covers the slot before seating, you must strike them on the

wood ve to six times!! Failure to seat the poles correctly

could allow the poles to separate during use, which could

lead to serious personal injuries or property damage.

WARNING

**This Step Can Not be Reversed**

The attened end of the Pole Brace (AE)

attaches to the Base (AC). The angled end

attaches to the pole.

Only nger tighten the Nuts now.

Repeat for the other

Pole Brace.

Required For

This Page: MC

(4)

(2)

1007262

(2)

BE AA

(2)

Place the Base over the 1/2” x

15 3/4” Axle (AB) and step on the

Base so the Axle ts into the slots

in the bottom of the Base.

Rotate the Pole up so the 1/2” x 7” Axle (BF)

ts into the slots in the top of the Base.

Lay the pole on the ground with

the crimped side of the Top

Pole facing the ground.

HA HB

Completely tighten all Base and

Pole Brace hardware now.

Tip the system forward so

the pole is resting on the

ground. DO NOT stand

the system up until it is

lled with weight later in

the instructions.

1007262

Required For This Page:

7/16” Wrench

Pliers

(1)

Andere Handbücher für 1270

Inhaltsverzeichnis

Andere Lifetime Spielgeräte und Spielplatzausstattung Handbücher

Lifetime

Lifetime 90980 Bedienungsanleitung

Lifetime

Lifetime 91155 Bedienungsanleitung

Lifetime

Lifetime 90135 Bedienungsanleitung

Lifetime

Lifetime A-FRAME PLAYSET 90042 Bedienungsanleitung

Lifetime

Lifetime 90136 Bedienungsanleitung

Lifetime

Lifetime 90143 Bedienungsanleitung

Lifetime

Lifetime 90850 Bedienungsanleitung

Lifetime

Lifetime 101301 Bedienungsanleitung

Lifetime

Lifetime 90941 Bedienungsanleitung

Lifetime

Lifetime A-FRAME PLAYSET 90042 Bedienungsanleitung

Lifetime

Lifetime 90762 Bedienungsanleitung

Lifetime

Lifetime 90994 Bedienungsanleitung

Lifetime

Lifetime ACE FLYER TEETER-TOTTER Bedienungsanleitung

Lifetime

Lifetime 90951 Bedienungsanleitung

Lifetime

Lifetime 90797 Bedienungsanleitung

Lifetime

Lifetime 90240 Bedienungsanleitung

Lifetime

Lifetime 90188 Bedienungsanleitung

Lifetime

Lifetime BIG STUFF 91079 Bedienungsanleitung

Lifetime

Lifetime DOUBLE ADVENTURE 90971 Bedienungsanleitung

Lifetime

Lifetime A-FRAME PLAYSET 90042 Bedienungsanleitung

Lifetime

Lifetime ADVENTURE CASTLE 91090 Bedienungsanleitung

Lifetime

Lifetime A-FRAME PLAYSET 90042 Bedienungsanleitung

Lifetime

Lifetime DOUBLE SHOT 90056 Bedienungsanleitung

Lifetime

Lifetime 90065 Bedienungsanleitung

Beliebte Spielgeräte und Spielplatzausstattung Handbücher anderer Marken

FUNormous

FUNormous Disney Junior MICKEY MOUSE Bedienungsanleitung

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Bedienungsanleitung

PoolMaster

PoolMaster 72775 Bedienungsanleitung

Palmako

Palmako 4743142009857 Installationshandbuch

BOERPLAY

BOERPLAY PSTE000.019 Bedienungsanleitung

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Benutzerhandbuch

stilum

stilum Erika Bedienungsanleitung

Costway

Costway NP10816 Bedienungsanleitung

Trigano

Trigano VABI Bedienungsanleitung

Outward

Outward OUT116 Bedienungsanleitung

GALOPIN

GALOPIN ARC02 Bedienungsanleitung

stilum

stilum levis Technische Daten

Ledon

Ledon BASIC Bai LB012 Bedienungsanleitung

BOERPLAY

BOERPLAY PSTE115.002 Bedienungsanleitung

Europlay

Europlay S306 Programmierhandbuch

SportsPlay Equipment

SportsPlay Equipment 361-509H Bedienungsanleitung

Ledon

Ledon 302250 Bedienungsanleitung

Costway

Costway NP10441 Bedienungsanleitung