Lifetime 72005 Kurzanleitung

10/1/2006

VISIT THE LIFETIME WEB SITE:

WWW.LIFETIME.COM

COMPETITION SERIES POWERLIFT®

BASKETBALL SYSTEM

MODEL #72005

ASSEMBLY INSTRUCTIONS

AND OWNER’S MANUAL

WARNING

Failure to comply with any of the warnings in

these instructions may result in serious personal

injuries such as cuts, broken bones, nerve damage,

paralysis, brain injury, or death. Failure to comply

may also result in property damage. Please heed

all warnings and cautions. To ensure your safety, do

not attempt to assemble this system without reading

and following all instructions carefully. Identify and

inventory the parts using the Parts List.

**For U.S. and Canada Customers ONLY:**

IF ASSISTANCE IS NEEDED,

DO NOT CONTACT THE STORE!!!

CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)

Call, or visit our Website for Saturday hours.

**Customers outside the U.S. or Canada, please contact the store.**

Save this instruction in the event that the manufacturer has to be contacted for replacement parts.

INSTRUCTION #1019132

**A MINIMUM OF TWO ADULTS ARE

REQUIRED FOR ASSEMBLY**

Copy

PARTS LIST

HARDWARE IS ACTUAL SIZE

(Unless otherwise indicated)

(Not actual size)

(Not actual

size)

RA RB

RD RF

RI RJ LA

SAFETY INSTRUCTIONS

Most injuries are caused by misuse and/or not following instructions. Use

caution when using this system.

Owner must ensure that all players know and follow these rules for safe operation of

the system.

To ensure safety, do not attempt to assemble this system without following the

instructions carefully. Check entire box and inside all packing material for parts and/

or additional instruction material. Before beginning assembly, read the instructions

and identify parts using the hardware identier and parts list in this document.

Proper and complete assembly, use and supervision are essential for proper

orientation and to reduce the risk of accident or injury. A high probability of serious

injury exists if this system is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR

PROPERTY DAMAGE AND WILL VOID WARRANTY.

• If using a ladder during assembly, use extreme caution.

• Two capable adults are recommended for this operation.

• Check base daily for leakage. Leaks will cause system to fall.

• Assemble the pole sections properly. Failure to do so could cause the pole

sections to separate during play or transport.

• Minimum operational height is 7’6” (2.23m) to the rim.

ID Part # Description Qty

TP 1018842 Top Pole 1

MP 1018878 Middle Pole 1

BP 1018882 Bottom Pole 1

PA HA01800 Gas Spring 1

PB 825619 Rim 1

PC 1018938 Short Y-Arm 2

PD 1018939 Long Y-Arm 2

PF 1018837 Rear Lifter Arm 2

PG ZA10185 Bellows 1

PH 1018977 Backboard 1

PI 502027H Adjustment Handle 1

PJ 502049G Trigger 1

FS16400 Warning Sticker (Applied) 1

PK 604091 Height Sticker 1

PM CF01700 Pole Cap 1

PN DD00800 Net 1

PO 502056 Plastic Guard 1

PP CA00885 Zip Tie 2

PQ 1008630 Spring Bracket 1

PR 800165 Rim Cover Plate 1

PT Z090013 Clamp Plate 2

PU Z090014 Hold Down Base Bracket 2

PV ZA01800 Bracket Back Plate 2

AG 510022 Wheel 2

AH BD00100 1/2” x 8” Axle 2

AI 510035 Base Cap 1

AJ 510082 Base 1

AK ZA02600 U-Bolt Washer Plate 1

AP 1018883 Pole Brace 2

AR CH00199 Slide Collar 1

AS CH00399 Locking Knob 4

AT 510011 Base Plug 1

AU CA00299 Left Frame Pad 1

AV CA00399 Right Frame Pad 1

AW CA00999 Bottom Frame Pad 2

AX 1018699 Slide Collar Clamp 1

AY 1018587 Slide Collar Bracket 2

Rim Hardware (1001327)

RA BS01000 #7 x 3/8” Screw 4

RB 300104 3/8” Push Nut 2

RC 302009 5/16” x 1 1/4” Carriage Bolt 2

RD 300128 Jam Nut 2

RE 302084 4” U-Bolt 1

RF 302090 5/16” Nylock Flange Nut 4

RG 1001137 Compression Spring 2

RH 510038 3/8” x 5 1/2” Axle 1

RI 804018 Rim Pivot Bracket 1

RJ 804033 Spring Retainer Plate 1

Competition Lock Down Hardware (HH00400)

LA 300145 3/8” Zinc Nut 2

LC 300203 3/8” x 5.31” J-Bolt 2

LD 300204 3/8” x 3/4” Eye Bolt 2

LE 302204 Cement Anchor 2

ID Part # Description Qty

Main Hardware (HH00600B)

MA 300029 1/2” x 7 1/8” Hex Bolt 3

MB 300040 1/2” Nylon Washer 4

MC 300031 3/8” Flat Washer 2

MD 300043 Cotter Pin 1

ME 300055 1 1/2” Metal Pin 1

MF BB00500 1/2” x 1 3/4” Hex Bolt 4

MG 301008 1/2” Centerlock Nut 7

MH 301051 3/8” x 5” Hex Bolt 2

MI 300073 1/2” Flat Washer 8

MJ 302008 3/8” Centerlock Nut 2

ML 500008 1/2” x 1/5” Spacer 4

MN 500041 3/8” x 1/4” Spacer 2

MQ 500081 Grease Packet 1

MK 500114 Finish Plug Cap 4

MR 800264 .510 x 3.91 Spacer 2

MT 800328 3/4” x 4 1/5” Spacer 1

Slide Collar Hardware (1013432)

SA 300186 #10 x 1” Self-Drilling Screw 4

SB 502073 Slide Collar Stop 4

SC 300027 5/16” x 3/4” Hex Bolt 1

SD 300097 5/16” Nylock Nut 1

Pole Joint Hardware (HD9081)

JA 300017 #10 x 5/8” Self-Drilling Screw 2

Frame Pad Hardware (HH00700)

FA BS00100 #10 x 3/4” Self-Drilling Screw 10

Handle Hardware (1017923)

HA 302007 3/8” x 6 1/2” Hex Bolt 2

HB 300101 Release Pin 1

MJ 302008 3/8” Centerlock Nut 2

HD 300187 1/2” x 6 1/2” Hex Bolt 1

MG 301008 1/2” Centerlock Nut 1

PARTS LIST

(Not actual size)

MB MC MD

MI MJ ML MN

SA SB

JA FA

BEFORE BEGINNING ASSEMBLY

PARTS LIST

ID Part # Description Qty

Base Hardware (HH01800B)

BA 300073 1/2” Flat Washer 2

BD 300097 5/16” Nylock Nut 4

LA 300145 3/8” Zinc Nut 1

BF 300152 1/2” x 9” Hex Bolt 1

MG 301008 1/2” Centerlock Nut 1

BH 301050 3/8” x 1 1/2” Hex Bolt 2

MJ 302008 3/8” Centerlock Nut 2

MH 301051 3/8” x 5” Hex Bolt 1

BK 302071 5/16” x 3/4” Carriage Bolt 4

A. Identify and inventory all parts using the checklist boxes on the Parts

List. Keep the hardware bags and their contents separate. If any parts

are missing, call our Customer Service Department.

B. Test t all Bolts by inserting them into their respective holes. If

necessary, carefully scrape away any excess powder coating buildup

from inside the holes. Do not scrape away all of the powder coating.

Bare metal may rust. You may need to pound some bolts into place

with a hammer or mallet.

POLE SECTION IDENTIFICATION

Identify the pole sections before beginning assembly. Failure to assemble

the pole sections correctly may result in severe personal injury or property

damage as described on Page One.

ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY

CANNOT BE SEPARATED.

Note: Tapers and ares are exaggerated in the illustrations.

Top Pole:

Four holes at the

top of the pole, four

holes in the middle

and two holes at

the bottom.

Bottom Pole:

Slots at the top

of the pole and

two holes at the

bottom. Shortest

pole. Warning

Sticker.

Middle Pole:

Slots at the

top of the

pole.

TP MP

BA BD BH BK

Tools and Materials Required

for Assembly

(Not Included)

1. Adjustable Wrench

2. Hammer or Mallet

3. 1/2” Wrenches (2)

4. 9/16” Wrenches (2)

5. 3/4” Wrenches (2)

6. Scrap Wood or

Cardboard

7. Tape Measure

8. Electric Drill

9. Pliers

10. Funnel

11. 519 lbs. Sand or

Water supply

12. Phillips Screwdriver

13. Scissors or Wire

Cutters

14. Pencil or Marker

15. 1/2” Masonry Bit*

16. Hammer Drill*

*Optional for lockdown

feature

Required For This

Page:

HH00600B

9/16” Wrenches

(2)

Small

holes

Large

holes

The small notch in the Sticker

ts around the hole in the pole.

5” Mark

Make a mark 5

inches from the

slotted end of the

Middle Pole.

Strike the poles rmly on scrap

wood or cardboard ve to six

times.

Do not hit your feet with the pole,

as serious injury could occur.

The poles must be seated together. Even if they reach the 5-inch mark before seating, you must strike them on

the wood ve to six times! Failure to seat the poles correctly could allow the poles to separate during use, which

could lead to property damage or serious personal injuries such as those listed on Page One.

WARNING

If your pole sections

do not reach within

1/2 inch of the 5-inch

mark after seating,

DO NOT COMPLETE

ASSEMBLY. Call

our Customer

Service number for

assistance.

(2)

The instructions in the following steps must be followed exactly. Failure to properly orient the

pole sections will render the pole unusable. If the pole sections are assembled incorrectly,

you will have to purchase new ones from our Customer Service Department.

*The back of the Top Pole (TP) is the side with the Spring Bracket. FRONT

SIDE

BACK

SIDE

Spring

Bracket

5-inch

mark

Make a mark 5 inches

from the slotted end of the

Bottom Pole (BP).

Slide the Middle Pole over

the Bottom Pole. Strike

each end of the pole rmly

on wood or cardboard ve

to six times.

Both pole joints must be

within 1/2-inch of the 5-inch

mark. If either joint fails to

reach the mark, DO NOT

COMPLETE ASSEMBLY.

Call our Customer Service

number for assistance.

Slide the Top Pole

over the Middle Pole.

*The holes in the bottom of the Bottom Pole (BP) are toward the back of the pole. TP

Tighten the

Nuts securely.

Holes

BP TP

Pencil or Marker

Tape Measure

Warning

Sticker

Apply the Height Sticker (PK) so it

wraps around the opposite side of the

Pole as the Spring Bracket (PQ).

Make sure the Warning Sticker and the Spring Bracket are on opposite sides.

321

4 5

1”

INSTALLING THE POLE JOINT

SAFETY SCREWS:

Required For This Page:

HD9081

Lay the pole on the ground.

The pole joint safety Screws do not replace

proper pole seating--both are required.

Always wear safety glasses when

operating power tools.

Measure up one inch from the lower pole joint

on the side of the pole with the Spring Bracket

and begin inserting the Screw (JA). Once the

Screw has entered the pole, slow the drill down

to avoid stripping the Screw.

(2)

You must follow all instructions for pole joint safety

Screw attachment and pole seating. Failure to do

so could allow the poles to separate, resulting in

property damage or serious personal injuries such

as those listed on Page One.

WARNING

Repeat the process for the upper pole

joint with the remaining Self-Drilling

Screw (JA).

Lay the Base upside down.

HH01800B

You may need to strike the Axles (AH)

with a hammer or mallet to drive them

into the slots.

Turn the Base over so the

Wheels are on the bottom.

Complete for the other side of the Base.

1/2” Wrench

(4)

Rubber

Gasket

The Rubber Gasket should be

inside the Base Cap (AI). If there

is no Gasket, call the Customer

Service number on Page One.

Screw the Base Cap

onto the Base (AJ).

Completely tighten the Nuts.

Hammer/Mallet

Electric Drill

987

9/16” Wrenches

Required For This Page:

(1)

3/4” Wrenches

HH01800B

(1)

(Not

actual

length)

9”

(2)

The Spring Bracket

on the Top Pole

should face the

Base.

Rest the Base at on the ground and have one

person support the pole.

Snap the Slide Collar (AR) onto the Middle Pole

and insert the Pole Braces (AP) into the Collar.

Bend the Slide Collar Clamp

(AX) around the Slide Collar.

One person should

position the Pole at

an angle in the front

of the Base. A second

person should slide

one washer onto the

bolt, then push the bolt

through the rst hole in

the base and the rst

hole in the pole.

Slide the Bolt (MH) through the Locking Knob (AS),

Slide Collar Clamp (AX), Slide Collar and Pole Braces.

The rectangular cutout

in the Clamp (AX)

should t over the

“Bubble Level” on the

Slide Collar.

Move the pole the

rest of the way

into the base and

slide the bolt the

remainder of the

way through the

pole and the other

side of the base.

Push washer and nut

onto the bolt and tighten

the bolt until it is at the

top of the thread.

9/16” Wrenches

Required For This Page:

HH01800B

(1)

(2) (2)

Pliers

Scissors or Wire Cutters

BH MJ

Place the Knob (AS)

and Nut (LA) back onto

the bolt and tighten

completely.

Use another Bolt to tap the

3/8” Zinc Nut (LA) into the

Locking Knob (AS).

12 Place the Zinc Nut (LA) on the end

of the bolt and tighten in order to pull

the sides of the slide collar together.

Do not stand the system up until

the Base is lled with weight.

Zip Tie

(PP)

Larger

End

Use pliers to tighten

the Zip Ties (PP)

securely. Cut off the

ends of the Zip Ties.

Zip Tie

(PP)

Tighten each Nut only

until it is ush with the

end of the Bolt.

After the Pole Braces (AP) are attached

to the Base, loosen one of the Knobs on

the Slide Collar and adjust the pole until

it is upright. Tighten the Knobs securely.

Tip the system forward until the pole

rests on the ground.

The bottom of the Bellows (PG)

overlaps the Spring (PA) by 1”. The

top is 1/2” from the top of the Spring.

1413 Attach the pole braces (AP) to the

base on each side.

Remove the Zinc Nut (LA)

from the end of the bolt.

Required For This Page:

1017923

(2)

HH00600B

(2)

(1)*

*(Not actual size)

(1)

Pliers

Tighten the Nut until it

is ush with the Bolt.

MD ME

Use pliers to

bend the Cotter

Pin (MD) as

shown above.

The Release Pin (HB) should t into

the channels in the Trigger (PJ).

Tighten the Nut until it is

ush with the Bolt.

(1)*

(2)

1001327

Tighten the Nut until it is

ush with the Bolt.

PA PF

Line up the Rear Lifter Arms

(PF) with the Gas Spring (PA).

(1)

9/16” Wrenches

(1)

3/4” Wrenches

MG HB

171615

19 20 21

Required For

This Page:

1/2” Wrenches

1001327

(2)

(4)

(Not

actual

size)

(1)

(2)

The Push Nuts (RB)

should be convex

side out.

Lay the Backboard (PH) face

up with the Rim holes exposed

over the edge of a table.

Tighten the Jam Nuts (RD) onto

the U-Bolt as far as they will go.

RF RF

Tighten the Nylock

Flange Nuts (RF) down

as far as they will go.

Insert the U-Bolt (RE) through the U-

Bolt Washer Plate (AK) and the upper

holes in the back of the Backboard.

Screwdriver

242322

25 26 27 28

Inhaltsverzeichnis

Andere Lifetime Spielgeräte und Spielplatzausstattung Handbücher

Lifetime

Lifetime 90136 Bedienungsanleitung

Lifetime

Lifetime 90951 Bedienungsanleitung

Lifetime

Lifetime 1258 Bedienungsanleitung

Lifetime

Lifetime 90188 Bedienungsanleitung

Lifetime

Lifetime 90804 Bedienungsanleitung

Lifetime

Lifetime ADVENTURE CASTLE 91090 Bedienungsanleitung

Lifetime

Lifetime 90850 Bedienungsanleitung

Lifetime

Lifetime CLIMBING DOME Bedienungsanleitung

Lifetime

Lifetime 290633 Bedienungsanleitung

Lifetime

Lifetime A-FRAME PLAYSET 90042 Bedienungsanleitung

Lifetime

Lifetime 90762 Bedienungsanleitung

Lifetime

Lifetime ADVENTURE TOWER 90830 Bedienungsanleitung

Lifetime

Lifetime 91155 Bedienungsanleitung

Lifetime

Lifetime DOUBLE SHOT 90056 Bedienungsanleitung

Lifetime

Lifetime 90980 Bedienungsanleitung

Lifetime

Lifetime 90952 Bedienungsanleitung

Lifetime

Lifetime 90269 Bedienungsanleitung

Lifetime

Lifetime ADVENTURE TUNNEL Bedienungsanleitung

Lifetime

Lifetime 0040 Kurzanleitung

Lifetime

Lifetime 90941 Bedienungsanleitung

Lifetime

Lifetime 101301 Bedienungsanleitung

Lifetime

Lifetime A-FRAME PLAYSET 90042 Bedienungsanleitung

Lifetime

Lifetime 90135 Bedienungsanleitung

Lifetime

Lifetime 90065 Bedienungsanleitung

Beliebte Spielgeräte und Spielplatzausstattung Handbücher anderer Marken

FUNormous

FUNormous Disney Junior MICKEY MOUSE Bedienungsanleitung

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Bedienungsanleitung

PoolMaster

PoolMaster 72775 Bedienungsanleitung

Palmako

Palmako 4743142009857 Installationshandbuch

BOERPLAY

BOERPLAY PSTE000.019 Bedienungsanleitung

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Benutzerhandbuch

stilum

stilum Erika Bedienungsanleitung

Costway

Costway NP10816 Bedienungsanleitung

Trigano

Trigano VABI Bedienungsanleitung

Outward

Outward OUT116 Bedienungsanleitung

GALOPIN

GALOPIN ARC02 Bedienungsanleitung

stilum

stilum levis Technische Daten

Ledon

Ledon BASIC Bai LB012 Bedienungsanleitung

BOERPLAY

BOERPLAY PSTE115.002 Bedienungsanleitung

Europlay

Europlay S306 Programmierhandbuch

SportsPlay Equipment

SportsPlay Equipment 361-509H Bedienungsanleitung

Ledon

Ledon 302250 Bedienungsanleitung

Costway

Costway NP10441 Bedienungsanleitung