Light Emotion P64LEDC Bedienungsanleitung
1 of 4 pages
WWW.LIGHTEMOTION.COM.AU
P64LEDC
Controller for the P64LED and P64PLED
This manual contains important information about the safe installation and use of this product
Please read this instruction manual carefully before installing or operating
Please keep these instructions in a safe place for future reference
2 of 4 pages
Congratulations on the purchase of your P64LEDC by Light Emotion. LED Controller Panel can control the led
par can, led strobe and make colorful and dynamic light scenery effects.
CONTENTS
SECTION Page
WHAT IS INCLUDED, SAFETY INSTRUCTION 2
OPERATION 3
SPECIFICATIONS 4
Please note that as part of out ongoing commitment to continuous improvement and product
development, the specifications in this manual are subject to change without notice. Whilst every care has
been taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement.
WHAT IS INCLUDED:
CAUTION: Do not use sharp objects whilst unpacking this product
•1x P64LEDC
•1x12V DC power supply
•1xWarranty Card & User Manual
Please note: Some of the items above may be fitted to the product by the manufacturer.
SAFETY INSTRUCTIONS:
Please read these instructions carefully. It includes important information about the installation usage
and maintenance of this product.
•Please keep this User Manual for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage and that the line voltage you are
connecting to is not higher than that stated on the rear panel of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not expose
fixture to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surface. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to replace
with same fuse source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than this.
3 of 4 pages
•In the event of serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center.
•Never connect the device to dimmer pack.
•Make sure power cord is never crimped or damaged.
•Never disconnect power cord by pulling or tugging on the cord.
•Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.
•Avoid direct eye exposure to the light source while it is on.
OPERATION:
Sketch picture:
4 of 4 pages
1. Select color mode:
Press “COLOR SELECT” button, the LED indicator D2 is on, and then you can press: RED，
ORANGE，YELLOW，GREEN，CYAN，BLUE，PURPLE，MAGENTA，WHITE to choose your
preferable color. You can also press R, G, B to choose Red, green, or blue.
2. Select built-in programs mode:
Press “PROG SELECT” button, the LED indicator D3 is on, then you can select the built-in programs
via “PROG SELECT” slider, change the running speed (under static color, this function is invalid) via
“SPEED” slider and the frequency of flash (under sound activated to adjust the sound sensitivity) via
“flash/sensitivity” slider.
3. Auto run mode:
Press “AUTO” button, the LED indicator D4 is on. Now you can change the running speed via
“SPEED” slider and the frequency of flash via “FLASH/SENSITIVITY” slider. But you can not use
“PROG SELECT” slider in this mode.
4. SOUNDACTIVE mode:
Press “SOUND ACTIVE” button, the LED indicator D5 is on. Then you can change the sound active
sensitivity via “FLASH/SENSITIVITY” slider. You can not use “PROG SELECT” slider and
“SPEED” slider in this mode.
5. Any time when press “HOLD”:
Press the “HOLD” button to lock the current operation, the LED indicator D2 will be on to show you
in the HOLD mode.
Under “HOLD” condition and turn off power, then turn on power again, the controller keep the
current scene.
6. Any time (not in HOLD mode) when press “BLACK OUT”:
Press “BLACK OUT” button to black out, the LED indicator D6 will be on to show you in the
BLACK OUT mode.
SPECIFICATION:
•Power In: 9-12V 300mA
•Power consumption: 3.6 W
•Size: 22X14X3.6cm
•Weight: 1kgs
LIGHT EMOTION LEDC CONTROLLER
WAREHOUSE SOUND SYSTEMS PTY ;LTD
PO BOX 130 FITZROY
PH: 94174866 EMAIL: INFO@WAREHOUSESOUND COM
Inhaltsverzeichnis
Andere Light Emotion Controller Handbücher
