Light Emotion HALFBALL Bedienerhandbuch

www.lightemotion.com.au

HALFBALL

Rotating LED DMX Half Ball with 5 x 3W RGBWA LEDs.

User’s instruction manual

This manual contains important information about the safe installation and use of this product

Please read this instruction manual carefully before installing or operating

Please keep these instructions in a safe place for future reference

V1.00

Contents

1. Safety Instructions 2

2. Installation 3

3. Features 3

4. Menu Operation 4

5. DMX Channel Allocation and functions tables 4

6. DMX Control Connection 5

7. DMX Address Setting 5

8. DMX Terminator 6

9. Cleaning and Maintenance 6

10. Technical Data 7

11. Warranty 7

Introduction

Thank you for the purchase of your HALFBALL LED DMX rotating lighting effect by Light

Emotion. We are confident you will be satisfied with your purchase and enjoy many years of

use from this Professional Light Emotion product. Please read these instructions carefully to

ensure the product is well look after and used correctly to avoid any potential problems.

Please note that as part of our ongoing commitment to continuous improvement and product

development, the specifications in this manual are subject to change without notice. Whilst

every care has been taken in the preparation of this manual we reserve the right to change

specifications in the course of product improvement.

What is in the box:

- 1 x HALFBALL Lighting Effect

- 1 x Power Cable (may be attached)

- This user manual

1. Safety Instructions:

Please read these instructions carefully. It includes important information about the installation

usage and maintenance of this product.

- Please keep this User Manual for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

- Always make sure that you are connecting to the proper voltage and that the line voltage you

are connecting to is not higher than that stated on the sticker of the fixture.

- This product is intended for indoor use only. To prevent risk of fire or shock, do not expose

fixture to rain or moisture.

- Make sure there are no flammable materials close to the unit while operating.

- The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surface. Be sure that no ventilation slots are blocked.

- Always disconnect from power source before servicing.

- Secure fixture to stands, trussing and the like using a safety chain.

- Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than

this.

- In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center.

- Make sure power cord is never crimped or damaged.

- Never disconnect power cord by pulling or tugging on the cord.

- Never carry the fixture directly from the cord. Carry by holding the base of the unit, and only

move when unit is upright.

- Avoid direct eye exposure to the light source while it is on.

2. Installation:

Caution: For safe mounting of this product, please read the following carefully.

- Use a suitable clamp to attach to lighting stand, trussing or bar, together with safety chain.

- When mounting the product, do not stand directly underneath the product

- Always use a safety chain when mounting the product on stands, trussing or bars. Make sure

the breaking strain rating of the chain is at least 10 times the weight of the product.

- Make sure there is adequate ventilation around the product.

- This product is designed to be mounted either upright or upside down. It cannot be used in a

side orientation – for example: the product cannot be used with the base mounted on the wall

in a perpendicular orientation. This will cause severe damage to the motor and drive shaft and

will cause the product to fail.

- Never look directly into the LED light sources of the product.

- For indoor use only – do not use outdoors.

- To avoid electrical shock, keep away from rain and moisture.

- Keep out of reach of children.

3. Features

This product is designed as an LED lighting effect and is only intended to be used as an LED

lighting effect for entertainment and display applications. Due to our ongoing commitment to

constantly reviewing and improving products, features and specifications are subject to change

without prior notice.

- LEDs: 5 x 3W RGBWA LED with average 50000 hours lifespan

- Lenses: 55

- Beam angle: 1 degree

- Control: DMX, Sound Activation, Stand Alone, Master/Slave

- DMX Channels: 2 or 5 channel control mode

- 3 pin XLR male and female DMX sockets

- Endless pan rotation

- Electronic strobing from 1-25 fps

- Built in programs and on-board control of features

- Weight: 2.9kg

- Packed Dimensions 272x272x254mm

4. Menu Operation

The 4 digit display menu features four buttons – Menu, up, down and enter. Pressing the

MENU button will access the features listed in the below table.

5. DMX Channel Allocation and functions table

5 channel DMX mode

MENU UP/DOWN Default Data Function

1 Addr 1-512 1 DMX Address setting

2 ChNd 5 Ch 5 Ch 5CH DMX mode

2 Ch 2CH DMX mode

3 ShNd

Sh 0 Sh 0 Show 0

Sh 1 Show 1

Sh 2 Show 2

4 SPEE 0-100 90 Show 0 - Show 2 speed setting

5 SoUn ON ON Sound on

，

Show 0 – Show 2 sound

OFF Sound off

，

Show speed controlled by SPEE

6 SoSE 0-100 90 Sound sensitivity

7 Ver V10 Software version

Channel Value function

CH1 Mode option

0-9

No function

10-89 Show 0

90-169 Show 1

170-255 Show 2

CH2 Speed and sound 0-249 Show 0,Show 1,Show 2 from slow to fast

250-255 Show 0, Show 1, Show 2 by sound

CH3 LED colour option

0-9

No function

10-198 Every 6 values as one colour program – 31 in total

199-225 Colour change single colour from slow to fast

226-255 Colour change multi colour from slow to fast

CH4 LED strobe

0-9

No function

10-244 LED strobe from slow to fast

245-255 LED strobe by sound

CH5

Rotation control

0-9

No function

10-127 Clockwise rotation from slow to fast

128-255 Anti-clockwise rotation from slow to fast

2 channel DMX mode

Channel Value Function

CH1 Mode option

0-9

No function

10-89 Show 0

90-169 Show 1

170-255 Show 2

CH2 Speed and sound 0-249 Show 0, Show 1, Show 2 speed from slow to fast

250-255 Show 0, Show 1, Show 2 by sound

6. DMX-512 Control Connection

Using a 3 pin XLR cable, you can connect the product to a DMX controller and then to

other fixtures with 3 pin XLR inputs and outputs. When not using DMX, multiple

fixtures can be connected together and operate under master/slave control. The signal

cable should have two core with shielded cable, the signal connectors are XLR input

and output connectors. Please refer to the below diagram:

7. DMX Address Setting

When being used in conjunction with a DMX controller, each fixture must be set a specific

starting address. When receiving signal, fixture will receive channel control signals of this

address from the DMX controller.

For simplicity, the user can use the same address for multiple fixtures but this will result in

each fixture providing exactly the same output and fixtures with the same DMX address cannot

be individually controlled.

To control each fixture individually via DMX, each fixture must have its own unique DMX

address. This fixture can operate in either 2 or 5 channel DMX mode. If running in 5 channel

DMX mode, then each DMX address for each fixture must be at least 5 channels apart.

So for example – assuming the first fixture is DMX channel 1, the second fixture would need

to be on channel 6, then the 3

channel 11 and so on. Some DMX controllers may group

fixtures in lots of 16 channels – so in that case, fixture 1 on channel 1, fixture 2 on channel 17,

3 on 33, and so on. Refer to your DMX controllers’ instruction manual on how best to manage

your DMX channel allocation.

Address 01 Address 06 Address 11

8. DMX-512 connection with DMX terminator

A DMX terminator helps to reduce ‘noise’ on the DMX chain, and makes the light respond to

control more accurately. It should be plugged in to the last fixture in any chain. For Terminator

connections please see below:

9. Cleaning and maintenance

From time to time it is recommended the product is cleaned to ensure maximum light output

and performance. Use a wet cloth to clean the housing as well as the lenses and base. Glass

cleaner is also suitable but alcohol based cleaners and solvents cannot be used as they will

cause damage to the product.

When used in a fixed long term installation such as a venue or club, the unit should be

periodically taken down from the installation and professionally cleaned. Dust build-up within

the unit can cause damage and ultimately failure of components.

DMX-controller

DMX512 120 Ohms

10. Technical Data

Input Voltage: AC100-240V 50/60Hz

LED: 5 x 3W RGBWA LED rated lifespan 50,000 hours

Power Consumption: 20w

Max ambient temp: 40

DMX connection: 3 pin XLR in and out

Net Weight: 2.9Kg

Packed Dimensions: 272x272x254mm

11. Warranty

This product is warranted for 2 years from your purchase date. We are confident that this

product will give many years of trouble-free operation but should an unlikely problem arise,

warranty claims must be via the original place of purchase, together with the original purchase

receipt. Please keep both your original purchase receipt and this instruction manual together

and in a safe place for future reference. Should the product be sold within the warranty period,

be sure to pass on both to the new purchaser so they are able to claim warranty should they

need to. We recommend you register your warranty online at www.industrygear.com.au.

Purchased from:_________________________________________

Contact Details:_________________________________________

Date Purchased:_________________________________________

Invoice/Receipt Number:__________________________________

Exclusively imported by LSW Imports and Distribution

PO Box 887, Kingsgrove, NSW, 2208

[email protected]

www.lightemotion.com.au

1800 643 111 (within Australia)

+612 9718 4900 (outside of Australia)

Inhaltsverzeichnis

Andere Light Emotion DJ-Equipment Handbücher

Light Emotion

Light Emotion LE60 Bedienerhandbuch

Light Emotion

Light Emotion COB150RGBW Bedienerhandbuch

Light Emotion

Light Emotion MOONSTAR4 Bedienerhandbuch

Light Emotion

Light Emotion P64LEDLITEWW Bedienerhandbuch

Light Emotion

Light Emotion BRUTE Bedienerhandbuch

Light Emotion

Light Emotion RAZORTRI Bedienungsanleitung

Light Emotion

Light Emotion DERBY4 Bedienerhandbuch

Light Emotion

Light Emotion LE90 Bedienungsanleitung

Light Emotion

Light Emotion P64100RGB Bedienerhandbuch

Light Emotion

Light Emotion Firefly Series Bedienungsanleitung

Light Emotion

Light Emotion P64LEDLITE Bedienerhandbuch

Light Emotion

Light Emotion MUSHROOMLED Bedienerhandbuch

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung